3.7m x 4.3m (12.1' x 14.1') grand gazebo with aluminum roof (63 pages)
Summary of Contents for Yardistry 1902316
Page 1
Predrill 1 - 5/16 x3 ,1/4 shank hex lag screw (5/16 flat washer) Show squaring unit should be 152¾ diagonally from post to post Revised 07-31-2020 3.658 m (12’) Yardistry – North America Toll Free Customer Support: 1.888.509.4382 3.658 m info@yardistrystructures.com (12’)
Wood is NOT flame retardant and will burn. Grills, fire pits and chimineas are a fire hazard if placed too close to a Yardistry structure. Consult user’s manual of the grill, fire pit or chiminea for safe distances from combustible materials.
Page 3
Limited Warranty Yardistry warrants that this product is free from defect in materials and workmanship for a period of one (1) year from the original date of purchase. In addition, for any product with lumber, all lumber is warranted for five (5) years against rot and decay. This warranty applies to the original owner and registrant and is non-transferable.
Instructions for Proper Maintenance Your Yardistry structure is designed and constructed of quality materials. As with all outdoor products it will weather and wear. To maximize the enjoyment, safety and life of your structure it is important that you, the owner, properly maintain it.
Assembly Tips Following are some helpful tips to make the assembly process smooth and efficient. PRE-ASSEMBLIES: (i.e. Post and Beam Assemblies, Roof Rafter Assembly, etc) • Work on a raised, solid and flat surface such as, a table or saw horse. •...
Page 6
Permanent Installation Examples Note: It is critically important you start with square, solid and level footings, concrete pad or deck to attach your Pavilion. We supply Post Mounts with this structure which gives you the flexibility to permanently install your structure to a pre-existing or new wood or concrete surface.
Page 7
Permanent Installation Examples cont. Concrete Patio [min. 3.353 m x 3.353 m (11’ x 11’)] with 15.24 cm (6”) clearance on all sides Anchoring Hardware not included Wood Deck [min. 3.353 m x 3.353 m (11’ x 11’)] with 15.24 cm (6”)clearance on all sides Anchoring Hardware not included Post Mount...
Part Identification ( Dimensions are approximate and are shown to assist in the identification of parts for assembly. Actual dimensions may be smaller or larger. 8pc. (913) - Trellis Joist A-1898.7mm (74-3/4") (Y50229-913) (Y70819-288) 1pc. Trellis Bracket (26 pk) 8pc. (914) - Trellis Joist B -1898.7mm (74-3/4") (Y50229-914) (Y70819-109) 10pc.
Page 9
Part Identification ( Dimensions are approximate and are shown to assist in the identification of parts for assembly. Actual dimensions may be smaller or larger. 8pc. 5/16 x 6" Hex Bolt (Y07718-360) 16pc. 5/16 x 5 1/4" Hex Bolt (Y07718-351) 24pc.
Page 10
Step 1: Inventory Parts - Read This Before Starting Assembly STOP STOP STOP STOP This is the time for you to inventory all your hardware, wood and accessories, referencing the parts identification sheets. This will assist you with your assembly. •...
Page 11
Step 2: Post Assemblies, Part 1 A: At the bottom of one (902) Pergola Post insert two 5/16” T-Nuts as shown in F2.2. Step 1 Post Mount to Post 2 - 5/16 x 1¼ Hex Bolt (5/16 flat, lock washer and t-nut) B: At the bottom of (902) Pergola Post place two Post Mounts tight to the bottom and inside faces as shown in 4 - #8x1½...
Page 12
Step 2: Post Assemblies, Part 2 Step 1 Post Mount to Post 2 - 5/16 x 1¼ Hex Bolt (5/16 flat, lock washer and t-nut) C: From the inside attach two #10 x 1-1/4” Pan Screws per mount These screws are installed at a slight angle. 4 - #8x1½...
Page 13
Step 2 Plinth to post 16 - #8x 1½ wood screw Step 2: Post Assemblies, Part 3 E: Place one (422) Plinth flush to the bottom and tight to the Post Mounts on each side of the (902) Pergola Post and attach with four #8 x 1-1/2”...
Page 14
Step 3: Attach Post Block Step 3 Post Block to post 2 - 5/16 x 6 Hex bolt (5/16 flat, lock washer and t-nut) A: In all four Post Assemblies, place one (920) Post Block inside the top of each (902) Pergola Post. Make sure holes in (920) Post Block align with holes in (902) Pergola Post then attach with two 5/16 x 6”...
Page 15
Step 4: Trellis Joist Assembly, Part 1 Step 4 Trellis Joist A and Trellis Joist B Assembly A: Interlock the cut-outs on two (913) Trellis Joist A and attach using four 5/16 x 1-1/2” Hex Bolts (with 5/16” lock 4 -5/16 x 1½ Hex Bolt (5/16 flat, lock washer and t-nut) washer, 5/16”...
Page 16
Step 5 Step 4: Trellis Joist Assembly, Part 2 Attach Splice to Trellis Joist A & B (center on the short side) 4 - #8 x 3 wood screw Predrill 2 - 5/16x3, ¼ shank hex lag screw (5/16 flat washer) D: On the short side of each Trellis Joist A Assembly and each Trellis Joist B Assembly centre one (918) Splice and attach with four #8 x 3”...
Page 17
8 - 5/16 x 4 hex bolt (5/16 flat, Lock washer and T-nut) 8 - #8 x 3 wood screw Step 5: Beam Assembly, Part 1 Step 6 A: At each end of one (921) Beam Middle connect one (905) Beam End using one (912) Connector Block as Attach Beam end to Beam Middle with connector Block.
Page 18
Step 5: Beam Assembly, Part 2 Step 6 Attach Beam end to Beam Middle with connector Block. (screw holes to the top of beam’s) 8 - 5/16 x 4 hex bolt (5/16 flat, Lock washer and T-nut) 8 - #8 x 3 wood screw C: Make sure (905) Beam Ends and (921) Beam Middles are tight together and flush on the top for each Beam Assembly then attach (921) Beam Middle and (905) Beam Ends to (912) Connector Blocks with four #8 x 3”...
Page 19
Step 6: Post and Beam Assembly A: Lay two Post Assemblies on a flat surface with the the bolt heads facing up. Place one Beam Assembly over (920) Post Blocks then attach with two 5/16 x 4” Hex Bolts (with 5/16” lock washer, 5/16” flat washer and 5/16” Step 7 Lay 2 post on flat surface and attach beam assembly and Gusset (make sure post are square to t-nut) per end.
Page 20
Step 7: Attach Trellis Joist A Assemblies Step 8 Stand up both Post to beam assemblies attach Trellis A Assembly to post (over hang Beam assembly 13”) 4 - 5/16 x 5¼ hex bolt (5/16 flat, lock washer and T-nuts) per side A: Stand both Post and Beam Assemblies then place four Trellis Joist A Assemblies on Beam Assemblies, two at each end, tight to each side of (920) Post Blocks.
Page 21
Step 9 Step 8: Attach Long Gussets, Part 1 Square Post to Trellis A and attach Long Gusset 2- 5/16 x 5 ¼ (5/16 flat, lock washer and T-nut) Predrill 1 - 5/16 x3 ,1/4 shank hex lag screw (5/16 flat washer) Show squaring unit should be 152¾...
Page 22
Step 9 Square Post to Trellis A and attach Long Gusset Step 8: Attach Long Gussets, Part 2 2- 5/16 x 5 ¼ (5/16 flat, lock washer and T-nut) Predrill 1 - 5/16 x3 ,1/4 shank hex lag screw (5/16 flat washer) Show squaring unit should be 152¾...
Page 23
Attach 4 Trellis Joist B to Middle Beam leaving 20 9/16 space between Trellis Joist. 4 - #10 X 1 ¼ Pan screw Step 9: Attach Trellis Joist B Assemblies Trellis Trellis Joist B Assembly Joist A F9.1 A: On each Beam Assembly Assembly measure 20-9/16”...
Page 24
Step 10: Trellis Assembly A: With one Trellis Bracket connect one (915) Short Trellis to one (916) Long Trellis using one 1/4 x 1-3/4” Hex Bolts (with 5/16” flat washer x 2 and 1/4” lock nut). (F10.1, F10.2 and F10.3) B: Repeat Step A to complete nine more Trellis Assemblies.
Page 25
Attach trellis to Trellis Joist A and B - Put one trellis 66 inches from the end of the trellis Joist then place 4 more towards the end leaving a space of 11 7/8th between. then do the same on the opposite Step 11: Attach Trellis Assemblies side.
Page 26
Step 12 Attach trellis to Trellis Joist A and B Step 11: Attach Trellis Assemblies - Put one trellis 66 inches from the end of the trellis Joist then place 4 more towards Part 2 the end leaving a space of 11 7/8th between. then do the same on the opposite side.
Page 27
Step 12: Attach Post Trims A: Flush to the top of each Post Assembly and tight to the bottom of the Beam Assembly attach four (917) Post Step13 Trims to each assembly with two #8 x 1-1/2” Wood Screws per (917) Post Trim. Make sure the rounded edges Attach Post trim flush to top of post, radius down 2 - #8 1 ½...
Page 28
Step 13: Attach Top Post Blocks A: Tight to the top and flush to the sides of outside and inside (917) Post Trims attach two (919) Top Post Blocks to each Beam Assembly with four #8 x 3” Wood Screws per (919) Top Post Block. Make sure bolt heads are Step 14 covered with the countersunk holes in (919) Top Post Block.
Page 29
Yardistry Plaque 2- #10 x 1 ¼ pan screw A: Attach Yardistry Plaque to a prominent location on your Pergola with two #10 x 1-1/4” Pan Screws. This provides warnings concerning safety and important contact information. A tracking number is provided to allow you to get critical information or order replacement parts for this specific model.
Page 32
À l’attention de: Service à la clientèle Anglais et français parlés / Inglés y francés hablado Yardistry would like to say “Thank you” for your time and feedback. Yardistry quiere “Agradecerle” por su tiempo y su opinión. Yardistry aimerait vous remercier d’avoir pris le temps de répondre au sondage.
Need help?
Do you have a question about the 1902316 and is the answer not in the manual?
Questions and answers