Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Yardistry Manuals
  4. Outdoor Furnishing
  5. YM12732
  6. Installation and operating instructions manual

Yardistry YM12732 Installation And Operating Instructions Manual

3.7 m x 4.3 m (12.1 ft x 14.1 ft) everyday gazebo
Hide thumbs

Advertisement

Quick Links

Download this manual
3.7 m x 4.3 m (12.1 ft x 14.1 ft)
Everyday Gazebo
Installation and Operating Instructions – YM12732
ITM. / ART. 1807331
HEIGHT:
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
3.1 m / 10.1 ft
THIS ITEM IS INTENDED FOR OUTDOOR DOMESTIC USE ONLY.
NOT FOR COMMERCIAL USE.
Revised 14-08-2024
4.3 m
14.1 ft
Yardistry – North America
Toll Free Customer Support:
1.888.509.4382
3.7 m
Mon - Fri, 8:30 am - 5:00 pm EST
12.1 ft
(excl. holidays)
English and French Spoken
For extended hours see our website:
www.yardistrystructures.com
info@yardistrystructures.com
Patents Pending
Y40000-2732
1
support@yardistrystructures.com

Advertisement

loading
Need help?

Need help?

Do you have a question about the YM12732 and is the answer not in the manual?

Questions and answers

Patrick Leddy
April 30, 2025

I can't tell where the 2 of the 4 screws placement is. Is it in the seam of the short and long roof panels. Also do I screw the outside of the panels? Im not understanding if I screw the outside panels how do I screw on the edging.P 33-34

0
1 comments:
Mr. Anderson
May 16, 2025

For the seam of the short and long roof panels on the Yardistry YM12732:

- Place the Short Panel Left to overlap the Long Panel Left and flush to the sides of part 2203.
- Place the Short Panel Right to overlap the Long Panel Right and flush to the side of part 2204.
- Attach all panels with 42 R0 (roofing screws), but do not overtighten to avoid damaging the panels.
- There should be no screws along the bottom row.
- There should be a slight overhang at the bottom of the Large Fascia Beam Assembly, but no overhang at the corners.
- Roofing screws should be hand-tightened to sit snug and tight without crushing the material.

This answer is automatically generated

0

Subscribe to Our Youtube Channel

Related Manuals for Yardistry YM12732

Summary of Contents for Yardistry YM12732

  • Page 1 3.7 m x 4.3 m (12.1 ft x 14.1 ft) Everyday Gazebo Installation and Operating Instructions – YM12732 ITM. / ART. 1807331 HEIGHT: IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY 3.1 m / 10.1 ft THIS ITEM IS INTENDED FOR OUTDOOR DOMESTIC USE ONLY.
  • Page 2 Wood is NOT flame retardant and will burn. Grills, fire pits and chimineas are a fire hazard if placed too close to a Yardistry structure. Consult user’s manual of the grill, fire pit or chiminea for safe distances from combustible materials.
  • Page 3 Limited Warranty Yardistry warrants that this product is free from defect in materials and workmanship for a period of one (1) year from the original date of purchase. In addition, for any product with lumber, all lumber is warranted for five (5) years against rot and decay. This warranty applies to the original owner and registrant and is non-transferable.
  • Page 4 Instructions for Proper Maintenance Your Yardistry structure is designed and constructed of quality materials. As with all outdoor products it will weather and wear. To maximize the enjoyment, safety and life of your structure it is important that you, the owner, properly maintain it.
  • Page 5 Assembly Tips Following are some helpful tips to make the assembly process smooth and efficient. PRE-ASSEMBLIES: (i.e. Post and Beam Assemblies, Roof Rafter Assembly, etc) • Work on a raised, solid and flat surface such as a table or saw horse. •...
  • Page 6 Permanent Installation Examples Note: It is critically important you start with square, solid and level footings, concrete pad or deck to attach your Gazebo. We supply Post Mounts with this structure which gives you the flexibility to permanently install your structure to a pre-existing or new wood or concrete surface.
  • Page 7 Permanent Installation Examples cont. Concrete Patio (min. 11 ft 11 in (3.63 m) x 13 ft 11 in (4.24 m)) with 6 in (15.24 cm) clearance on all sides Anchoring Hardware not included Wood Deck (min. 11 ft 11 in (3.63 m) x 13 ft 11 ft (4.24 m)) with 6 in (15.24 cm) clearance on all sides Anchoring Hardware not included Post...
  • Page 8 Part Identification ( Dimensions are approximate and are shown to assist in the identification of parts for assembly. Actual dimensions may be smaller or larger. 152.4 x 177.8 x 2387.6 mm (6 x 7 x 94") 23.8 x 133.4 x 200 mm (15/16"...
  • Page 9 Part Identification ( Dimensions are approximate and are shown to assist in the identification of parts for assembly. Actual dimensions may be smaller or larger. 28.8 x 76.2 x 1553.3 mm (1-1/8" x 3" x 61-1/8") 2pc. (2209) - Strap Short FSC (Y50229-2209) 28.8 x 76.2 x 2156.9 mm (1-1/8"...
  • Page 10 Hardware Identification ( Dimensions are approximate and are shown to assist in the identification of parts for assembly. Actual dimensions may be smaller or larger. 4pc. Ridge Cap Short 25.2 4pc. - Long Panel Right 4pc. - Short Panel Left (Y01036-132) (Y01036-129) (Y01036-126)
  • Page 11 Hardware Identification ( Dimensions are approximate and are shown to assist in the identification of parts for assembly. Actual dimensions may be smaller or larger. #8 x 1-1/2" 152pc. Wood Screw (Y06091-512) 1pc. - Hex Driver (Y00400-004) #8 x 2" 24pc.
  • Page 12 Hardware Identification ( Dimensions are approximate and are shown to assist in the identification of parts for assembly. Actual dimensions may be smaller or larger. 12pc. Hex Bolt 1/4 x 2-3/4" - (Y07718-223) 5/16 x 1-1/4" 28pc. Hex Bolt - (Y07718-311) 5/16 x 1-1/2"...
  • Page 13 • Please retain this information for future reference. You will need this information if you contact the Consumer Relations Department. PRODUCT NUMBER: YM12732 CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 1) CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 2) CARTON I.D.
  • Page 14 Step 2: Post Assemblies A: At the bottom of one (2220) insert two TN2 on the outside of each narrow side. (F2.2) B: At the bottom of the same (2220) place two Post Mounts tight to the bottom and inside faces on the narrow sides as shown in F2.1 and F2.2.
  • Page 15 Step 3: Short Beam Assembly Part 1 A: Connect one (2201) and one (2202) using two G3 (with LW2, FW12 and TN2) as shown in F3.1 and F3.2. B: Connect one (2198) to each end of one (2196) using two G3 (with LW2, FW12 and TN2) per end as shown in F3.1 and F3.2.
  • Page 16 Step 3: Short Beam Assembly Part 2 D: Place one Short Beam L-R Assembly tight to one Short Beam End Assembly so the ends are flush. Match the bolt holes in each (2198) with the bolt holes in (2201) and (2202). Attach with 18 S35. (F3.3 and F3.4) E: Repeat Step D to make a second Short Beam Assembly.
  • Page 17 Step 4: Long Beam Assembly Part 1 A: Connect one (2199) and one (2200) using two G3 (with LW2, FW12 and TN2) as shown in F4.1 and F4.2. B: Connect one (2197) to each end of one (2195) using one G3 (with LW2, FW12 and TN2) in the top holes per end as shown in F4.1 and F4.2.
  • Page 18 Step 4: Long Beam Assembly Part 2 D: Place one Long Beam Insert in between one Long Beam L-R Assembly and one Long Beam End Assembly then fit tight together so the beam assembly ends are flush. Match the bolt holes and wood screw pilot holes in both beam assemblies and Long Beam Insert.
  • Page 19 Step 5: Frame Assembly and Anchoring Part 1 A: Move your Post Assemblies to the final location. Make sure the ground is flat and level before continuing assembly. Short Beam F5.1 Assembly B: With one person at each Post stand two complete Post Assemblies.
  • Page 20 Step 5: Frame Assembly and Anchoring Part 2 Note: Pre-drill all pilot holes using a 1/8” drill bit before installing Lag Screws. D: Make sure each corner is square and level then attach Beam Assemblies to Post Assemblies with two LS9 (with FW12) per corner.
  • Page 21 Step 6: Attach Gussets and Roof Brackets Note: Pre-drill all pilot holes using a 1/8” drill bit before installing Lag Screws. Note: The bevelled ends on each gusset should always face away from the wood it is attaching to. A: Make sure the assembly is still square and level then facing one Long or Short Beam Assembly place one (2219) on the right hand side so the top fits tight to the Beam Assembly and the bottom fits tight to the Post Assembly.
  • Page 22 Step 7: Fascia Beam Assemblies A: Tightly connect one (443) and one (444) using one G1 (with LW2, FW12 and TN2) as shown in F7.1 and F7.2. Repeat to make a second Fascia Beam Assembly. B: Tightly connect one (435) and one (436) using one G1 (with LW2, FW12 and TN2) as shown in F7.3 and F7.4.
  • Page 23 Step 8: Small Roof Rafter Assembly Part 1 A: On each side of one (2206) place one (2203) and one (2204) so the tops and edges are flush and notches are facing up, then attach with two S11 per side. (F8.1 and F8.2) B: Place Fascia Beam Assembly from Step 7A on the bottom of (2203), (2204) and (2206) so the sides are flush then attach with two S35 at each end and two in the middle.
  • Page 24 Step 8: Small Roof Rafter Assembly Part 2 D: Place one (2209) in the notches of (2203), (2204) and (2206) so the ends do not overhang the outside edges of the outside boards then attach with six S2. (F8.5) E: Place one (2207) in the notches of (2203), (2204) and (2206) so the ends do not overhang the outside edges of the outside boards.
  • Page 25 Step 9: Attach Roof to Beam Brackets Small Roof Rafter Assembly A: On the back of one Small Roof Rafter Assembly, centered and flush to the bottom of (2212), (2213) and (2206) attach one Roof to Beam Bracket per board with one S34 in the top hole and one S10 in the bottom hole per bracket.
  • Page 26 Step 10: Large Roof Rafter Assembly Part 1 A: On each side of one (434) place one (2206) so the tops and edges are flush and notches are facing up, then attach with two S3 per side. (F10.1 and F10.2) B: Place Large Fascia Beam Assembly from Step 7B on the bottom of the (2206)s so the sides are flush and holes are centered on the (2206) then attach with two S35 per (2206).
  • Page 27 Step 10: Large Roof Rafter Assembly Part 2 D: Beside each (2206) place one (2203) and one (2204) so the tops and edges are flush, notches are facing up, and the bottom edges are flush to Large Fascia Beam Assembly. Attach with two S35 at the top and bottom of the rafters per side.
  • Page 28 Step 10: Large Roof Rafter Assembly Part 3 F: Place one (2208) in the notches of (2203), (2204) and (2206)’s so the ends do not overhang the outside edges of the outside boards then attach with eight S2. (F10.7) G: Place one (2211) in the notches of (2203) and one (2206) and one (2210) in the notches of (2204) and the other (2206) so the ends do not overhang the outside edges of the outside boards.
  • Page 29 Step 10: Large Roof Rafter Assembly Part 4 J: Turn Large Roof Rafter Assembly over then attach one (2214) to (2211) and (2210) with eight S11. Edges should be flush. (F10.8 and F10.9) K: Complete Steps F - J for both Large Roof Rafter Assemblies. F10.8 Front View (2206)
  • Page 30 Step 11: Attach Roof to Beam Brackets Large Roof Rafter Assemblies A: On the back of both Large Roof Rafter Assemblies, centered and flush to the bottom of (2212), (2213) and both (2206)’s attach one Roof to Beam Bracket per board with one S10 in the bottom hole and one S34 in the top hole per bracket.
  • Page 31 STOP STOP STOP STOP INSTALLING ROOFING MATERIAL CAUTION! Roofing material may have sharp edges! Wear gloves! HANDLE WITH CARE! Place roofing material on a non-abrasive surface before assembly as it can bend, dent and scratch easily. WARNING – DO NOT OVER TIGHTEN ROOFING SCREWS! Over tightening screws will cause roofing material to crush.
  • Page 32 STOP STOP STOP STOP INSTALLING ROOFING MATERIAL CAUTION! Roofing material may have sharp edges! Wear gloves! BE SURE TO REMOVE ALL PLASTIC COVERING, ON BOTH SIDES OF THE ALUMINUM PANELS AND TRIM, DIRECTLY BEFORE INSTALLING EACH PIECE. (One side is clear and the other is blue, both must be removed.) Example #1 Example #2 Overtightened and Crushed...
  • Page 33 Step 12: Attach Roof Panels - Small Roof Part 1 A: Place one Long Panel Left on the front of one Small Roof Rafter Assembly so it is flush to the side of (2203) and has a slight overhang at the bottom of the Fascia Beam Assembly. Holes should line up with (2206). (F12.1 and F12.2) B: Place one Long Panel Right on Small Roof Rafter Assembly so it overlaps the Long Panel Left and is flush to the side of (2204) and has a slight overhang at the bottom of the Fascia Beam Assembly.
  • Page 34 Step 12: Attach Roof Panels - Small Roof Part 2 E: Place one Short Panel Left on Small Roof Rafter Assembly so it overlaps the Long Panel Left and it is flush to the sides of (2203) and has a slight overhang at the bottom of the Fascia Beam Assembly. There should be no overhang at the corners.
  • Page 35 Step 13: Attach Ridge Clips and Roof Edges - Small Roof A: Place one Roof Edge Left 72.2 and one Roof Edge Right 72.2 on the bottom of each Small Roof Rafter Assembly so the ends are flush with the outside ends of the Fascia Beam Assembly and meet tight in the center. Attach both Roof Edges with 17 R0 per Small Roof Rafter assembly.
  • Page 36 Step 14: Attach Roof Panels - Large Roof Part 1 A: Place one Middle Panel on the front of one Large Roof Rafter Assembly so the holes that are 1 in (2.54 cm) from the short edge are at the top of the panel. The panel slightly overhangs the top of (434) and has an overhang at the bottom of the Large Fascia Beam Assembly.
  • Page 37 Step 14: Attach Roof Panels - Large Roof Part 2 C: Place one Short Panel Left so it overlaps the Long Panel Left and it is flush to the sides of (2203) and one Short Panel Right so it overlaps the Long Panel Right and it is flush to the side of (2204). There will be a slight overhang at the bottom of the Large Fascia Beam Assembly.
  • Page 38 Step 14: Attach Roof Panels - Large Roof Part 3 F: On one Large Roof Rafter Assembly place one (463) flush to the outside edges and centered on (434) then attach with three S35. (F14.5 and F14.6) F14.6 (463) (434) Flush F14.5 Large Roof Rafter...
  • Page 39 Step 15: Attach Ridge Clips and Roof Edges - Large Roof A: Place one Roof Edge Left 72.2 and one Roof Edge Right 96.2 on the bottom of each Large Roof Rafter Assembly so the ends are flush with the outside ends of the Large Fascia Beam Assembly and meet tight in the center.
  • Page 40 Step 16: Attach Roof Panels to Frame Part 1 A: From inside the Post Assemblies measure 4 ft 11 in (1.49 m) to mark the center of each Short Beam Assembly. (F16.1) B: With all four assemblers place one Large Roof Panel Assembly with Roof to Beam Brackets in front of the Post Assemblies then raise it up so it is centered on the Long Beam Assembly.
  • Page 41 Step 16: Attach Roof Panels to Frame Part 2 C: Lift a Small Roof Panel Assembly with Roof to Beam Brackets over Short Beam Assembly taking care not to drag the panel on the beams. Make sure the middle Roof to Beam Bracket lines up to the center mark and the Corner Rafters are flush with each other.
  • Page 42 Step 16: Attach Roof Panels to Frame Part 3 E: Lift second Large Roof Panel Assembly with Roof to Beam Brackets over Large Beam Assembly taking care not to drag the panel on the beams then set in place beside the Small Roof Panel Assembly. (F16.6) F: Starting at the bottom and working up connect Large Roof Panel Assembly to Small Roof Panel Assembly through the Corner Rafters with three H11 (with two FW12 and one LN1).
  • Page 43 Step 17: Roof Peak Assembly A: Insert two Carriage Bolts through the top of Peak Cap Long, into Peak Post then Spring Clip. The Spring Clip holds the assembly together. (F17.1) B: Insert one 1/4” Nut into each Peak Loop. Be careful, nut is loose and will fall out until attached to Peak Cap Assembly.
  • Page 44 Step 18: Attach Roof Peak to Roof Panels A: Insert Roof Peak Assembly in gap between Large and Small Roof Panels. Peak Cap Long to be lined up with Corner Rafters. (F18.1 and F18.2) B: Insert two Roof Peak Brackets through each Carriage Bolt and attach Peak Loop to Carriage Bolts then twist to tighten loosely.
  • Page 45 Step 19: Attach Final Roof Panel Part 1 A: Lift last Small Roof Panel Assembly (without Roof to Beam Brackets) over Short Beam Assembly taking care not to drag the panel on the beams. Panel fits under the Peak Cap Long, push up on Peak Loop to lift Peak Cap Long.
  • Page 46 Step 19: Attach Final Roof Panel Part 2 Remember to push up center to assist with alignment. B: Starting at the bottom and working up loosely connect Roof Panel Assemblies through the Corner Rafters with three H11(with two FW12 and one LN1) per side. To align bolt holes helper on the center ladder may have to push up in the center of the panels and others make sure corners are aligned.
  • Page 47 Step 19: Attach Final Roof Panel Part 3 C: On the Small Roof Rafter Assembly just installed, centered and flush to the bottom of (2212), (2213) and (2206), attach one Roof to Beam Bracket per board with one S10 in the bottom hole and one S34 in the top hole. (F19.5) Attach to (2212), (2213) and (2206)
  • Page 48 Step 20: Secure Roof Corners A: Make sure middle Roof to Beam Brackets are flush and tight to the Beam Assemblies. Lift in center if needed. B: From outside the assembly attach Roof Panel Assemblies together at the ends of the Fascia Beam Assemblies with two S3 per corner.
  • Page 49 Step 21: Attach Corner and Beam Caps A: At each corner place one Corner Cap tight to Fascia Assemblies, push up so the bottom is tight to the bottom of the assemblies then attach with four SM0 per Corner Cap. (F21.1 and F21.2) F21.1 F21.2 Large...
  • Page 50 Step 22: Secure Roof to Beam Brackets A: From inside the assembly attach Roof to Beam Brackets to Beam Assemblies with two S34 per bracket. (F22.1 and F22.2) F22.1 Inside View Beam Assembly F22.2 Roof to Beam Bracket Beam Assembly Hardware 28 x #12 x 1-1/4”...
  • Page 51 Step 23: Secure Roof Peak Brackets A: Tighten the six screws in Roof Peak Brackets then attach to Corner Rafters in the remaining holes with ten S12. (F23.1) F23.1 Roof Peak Bracket Corner Corner Rafter Rafter Corner Rafter Corner Rafter Roof Peak x 10 Bracket...
  • Page 52 Step 24: Attach Ridge Caps to Roof Panels A: On each corner of the assembly slide one Ridge Cap Long 81.5 over the Ridge Clips from the bottom up, with cut end leading. Slide Ridge Cap Short 25.2 over the Ridge Clips leading with the insert end to push the Ridge Cap Long 81.5 to the top.
  • Page 53 Step 25: Attach Tie Wrap Brackets and Ties A: Attach one Tie Wrap Bracket to each end of F25.1 Large Roof Panel Large Roof one (2205) with one S12 per bracket using the Panel inside holes. (2205) is tight to end of bracket. (F25.1, F25.2 and F25.3) B: With a helper place (2205) with brackets against a (2206) on each Large Roof Panel so...
  • Page 54 Step 26: Twist Bracket Installation A: Measure 3.75 in (9.53 cm) down from the inside of each post, place bottom of either 45° Twist Bracket LT or 45° Twist Bracket RT at measured location then attach to post and Corner Rafter (Left or Right) with four S34 per bracket. (F26.1 and F26.2) F26.1 F26.2...
  • Page 55 Step 27: Metal Hooks and Plaque Part 1 A: Two 50 mm Hooks are included with this unit for attaching wiring. They can be placed anywhere along the Corner Rafters as needed. Pre-drill with a 1/8” drill bit before installing. (F27.1 and F27.2) B: One Eye Lag is included with this unit for hanging items with a maximum weight of 22 lbs (10 kg).
  • Page 56 Step 27: Metal Hooks and Plaque Part 2 C: Attach Gazebo ID Plaque to a prominent location on your gazebo with two S10. This provides warnings concerning safety and important contact information. (F27.4 and F27.5) F27.4 F27.5 Gazebo ID Plaque Components Hardware 1 x Gazebo ID Plaque...
  • Page 57 Yardistry 375 Sligo Road West, P.O. Box 10, Mount Forest, ON Canada N0G 2L1 ®...
  • Page 58 NOTES support@yardistrystructures.com...
  • Page 59 NOTES support@yardistrystructures.com...
  • Page 60 English and French Spoken / Anglais et français parlés / Inglés y francés hablado Yardistry would like to say “Thank you” for your time and feedback. Yardistry aimerait vous remercier d’avoir pris le temps de répondre au sondage. Yardistry quiere “Agradecerle” por su tiempo y su opinión.

This manual is also suitable for:

1807331
Save PDF