Related Manuals for Emerson BETTIS TEC2 CCM
Summary of Contents for Emerson BETTIS TEC2 CCM
- Page 1 Programming Instructions TEC2-RS485-1001 Rev. 1 September 2015 TEC2 CCM Programming Instructions Using RS-485 UART Probe and STC Pins 36 and 38...
- Page 3 Programming Instructions Table of Contents TEC2-RS485-1001 Rev. 1 September 2015 Table of Contents Section 1: TEC2 CCM Programming Instructions Using RS-485 UART Probe and STC Pins 36 and 38 ......... 1 Table of Contents...
- Page 4 Section 1: TEC2 CCM Programming Instructions Programming Instructions September 2015 TEC2-RS485-1001 Rev. 1 Section 1: TEC2 CCM Programming Instructions Using RS-485 UART Probe and STC Pins 36 and 38 Figure 1 RS485 Setup Connect USB cable to the RS485 Adapter and plug the other end of the cable into the USB port on the computer.
- Page 5 Programming Instructions Section 1: TEC2 CCM Programming Instructions TEC2-RS485-1001 Rev. 1 September 2015 Figure 2 RS485 Adapter Box Connection Connect RS485 cable to STC pins 36 and 38. See Figure 3. Figure 3 STC Pins 36 and 38 Set all switches on the RS485 Adapter box to ON. See Figure 4. TEC2 CCM Programming Instructions...
- Page 6 Section 1: TEC2 CCM Programming Instructions Programming Instructions September 2015 TEC2-RS485-1001 Rev. 1 Figure 4 Adapter Switch Settings Go to Windows Control Panel and open device manager. See Figure 5. TEC2 CCM Programming Instructions...
- Page 7 Programming Instructions Section 1: TEC2 CCM Programming Instructions TEC2-RS485-1001 Rev. 1 September 2015 Figure 5 Windows Control Panel Determine the RS485 Adapter box Com Port Number. See Figure 6. Figure 6 Com Port Number Open the TEC-Flash.exe program. See Figure 7. TEC2 CCM Programming Instructions...
- Page 8 Section 1: TEC2 CCM Programming Instructions Programming Instructions September 2015 TEC2-RS485-1001 Rev. 1 Figure 7 TEC-Flash.exe Icon Select the correct Comm port and then select Open. See Figure 8. Figure 8 Open Comm Port Enter the Modbus Address. Click on Discover. Select Check box for the Actuator, then click on the CCM Tab.
- Page 9 Programming Instructions Section 1: TEC2 CCM Programming Instructions TEC2-RS485-1001 Rev. 1 September 2015 Figure 9 TEC-Flash Program Discover Tab On the CCM tab, click Read Version button on Step 1. Then Click Read CRC on Step 2. Then click Open File on Step 3. See Figure 10. Figure 10 Perform Steps 1 and 2 then click Open File Navigate to the directory that holds the BIN file you want to download.
- Page 10 Section 1: TEC2 CCM Programming Instructions Programming Instructions September 2015 TEC2-RS485-1001 Rev. 1 Figure 11 Open BIN File Figure 12 below shows that in Step 2 box, the CRC values of the code in the existing board “Stored” is the CRC in the code. Calc is the CRC that TEC-Flash calculated for the code on the board.
- Page 11 Programming Instructions Section 1: TEC2 CCM Programming Instructions TEC2-RS485-1001 Rev. 1 September 2015 After the bootloader has started, you should see “Firmware Upgrade in Progress” on the LDM. See Figure 13. You should see that Step 4, Start Bootloader now shows Complete in Green and that Step 5 is now enabled to Upgrade Application.
- Page 12 Section 1: TEC2 CCM Programming Instructions Programming Instructions September 2015 TEC2-RS485-1001 Rev. 1 Figure 14 Upgrade in Progress You should now see the Step 5 “In Progress” and the green download status bar. See Figure 15. Figure 15 Download in Progress. Takes 5 to 6 minutes to finish with wired connection.
- Page 13 Programming Instructions Section 1: TEC2 CCM Programming Instructions TEC2-RS485-1001 Rev. 1 September 2015 Figure 17 Application Started The code in the Actuator should now be running and the version should be the new version that you downloaded. TEC2 CCM Programming Instructions...
- Page 15 Tianjin 301700 Holland Fasor 6 P. R. China Székesfehérvár 8000 The Emerson logo is a trademark and service mark of Emerson Electric Co. T +86 22 8212 3300 Hungary Bettis is a mark of one of the Emerson family of companies.