Installing And Removing The Battery Pack; Maintenance; Available Accessories - Porter-Cable PCCGG001 Instruction Manual

EnGlish

Installing and Removing the Battery Pack

(Fig. G)

WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
nOTE: For best results, make sure your battery pack is
fully charged.
1. To install the battery pack
the battery pack with the rails inside the tool's handle
and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does not disengage.
2. To remove the battery pack from the tool, press the
release button 16 and firmly pull the battery pack out of
the tool handle. Insert it into the charger as described in
the charger section of this manual.
Using the Grease Gun (Fig. A)

WARNING: To reduce the risk of serious personal
injury, always maintain a grip on the handle
when operating the grease gun or positioning the
hose onto fittings.
1. To operate the grease gun, hold the grease gun by the
handle 3 , or place it on a stable surface upright on its
rubber feet 17 maintaining a grip on the handle.
2. Holding the hose by the flexible hose safety spring
guard 7 , connect the flexible hose grease coupler
other appropriate grease coupler, onto the grease fitting
to be filled.
3. Carefully depress the variable speed trigger switch to
begin the filling process. Once the correct amount of
grease has been dispensed, release the trigger and
remove the coupler from the grease fitting.
4. If the coupler does not release, there may still be residual
pressure in the line. Moving the coupler from side to side
can relieve the residual pressure so it can be removed
from the coupling.
5. If the coupler leaks excessively or does not hold on to the
grease fitting, it should be replaced.
Speed Selection (Fig. A)
The PCCGG001 features two speed settings for
greater versatility. speed 1, low output/high PSI, is
recommended for general lubrication applications. speed 2,
high output/low PSI, is recommended for general lubrication
applications not requiring high PSI such as large bearings or
filling areas where a lot of grease is required.
nOTE: Do not change speeds when the tool is running.
Always allow the tool to come to a complete stop before
changing speed.
1. To select speed 1 (low output/high PSI), turn the tool
off and permit it to stop. Slide the speed selector
towards the motor housing
2. To select speed 2 (high output/low PSI), turn the tool off
and permit it to stop. Slide the speed selector
towards the handle 3
nOTE: If the tool does not change speeds, confirm that
the speed selection switch is completely engaged in the
speed 1 or speed 2 position.
12
15 into the tool handle, align
5 .
21
.

MAINTENANCE


WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments, accessories or when filling
with grease. An accidental start‑up can cause injury.
Your PORTER-CABLE power tool has been designed to
operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
8 or
PCCGGA001
PCCGGA002
PCCGGA003
PCCGGA004
Accessories

WARNING: Since accessories, other than those
offered by PORTER‑CABLE, have not been tested with
this product, use of such accessories with this product
could be hazardous. To reduce the risk of injury, only
PORTER‑CABLE recommended accessories should be
used with this product.
Recommended accessories for use with your
product are available at extra cost from your local
dealer or authorized service center. If you need
assistance in locating any accessory, please contact
PORTER-CABLE call 1‑888‑848‑5175 or visit our website:
www.portercable.com
21 up
down

AVAILABLE ACCESSORIES

Heavy Duty
1/8" NPT Grease Gun Coupler
Heavy Duty, 3-Pack
1/8" NPT Grease Gun Coupler
Right Angle Grease Gun Coupler
Shoulder Strap