Subscribe to Our Youtube Channel
Related Manuals for Electrolux Professional WB5130H
Summary of Contents for Electrolux Professional WB5130H
- Page 1 Installation manual Washer extractor WB5130H, WB5180H Type W3... 438 9057-40/EN Original instructions 2022.08.24...
-
Page 3: Table Of Contents
Contents Contents 1 Safety Precautions ..........................5 General safety information......................6 Commercial use only........................6 Symbols............................6 2 Warranty terms and exclusions......................7 3 Technical data.............................8 Drawing ............................8 3.1.1 Barrier partition ........................9 Technical data .........................10 Connections ..........................10 4 Setup ............................... 11 Unpacking ..........................11 4.1.1 Unpacking for machines delivered on a base ..............12 4.1.2 Recycling instruction for packaging ..................16 Siting ............................17 Mechanical installation ......................17... -
Page 5: Safety Precautions
• The openings in the base, shall not be obstructed by a carpet. • Maximum mass of dry cloth: WB5130H: 14 kg, WB5180H: 20 kg. • A-weighted emission sound pressure level at working stations: –... -
Page 6: General Safety Information
Installation manual and breakfast type environments, areas for communal use in blocks of flats or in launderettes. 1.1 General safety information The machine is only intended for water-wash use. Do not hose down the machine with water. In order to prevent damage to the electronics (and other parts) that may occur as the result of condensation, the ma- chine should be placed in room temperature for 24 hours before being used for the first time. -
Page 7: Warranty Terms And Exclusions
Warranty will be applicable where the customer has used only genuine spare parts and has performed maintenance in accordance with Electrolux Professional user and maintenance documentation made available in paper or elec- tronic format. Electrolux Professional strongly recommends using Electrolux Professional approved cleaning, rinse and descaling agents to obtain optimal results and maintain product efficiency over time. -
Page 8: Technical Data
Cold water Hot water Cold/hot water Steam connection Drain Door opening, loading side: WB5130H: 280 x 280 mm, WB5180H: 320 x 280 mm Door opening, unloading side: WB5130H: ⌀ 395 mm, WB5180H: ⌀ 435 mm Plinth Barrier frame Barrier partition... -
Page 9: Barrier Partition
If machines are to be installed in an existing wall thicker than 100 mm please contact authorized service personnel. fig.6822A Aluminium section Rubber seal Barrier partition Removable barrier partition Minimum 70 mm, maximum 100 mm WB5130H 1650 WB5180H 1050 1650... -
Page 10: Technical Data
Installation manual 3.2 Technical data WB5130H WB5180H Weight, net Drum volume litres Drum diameter Drum speed during wash Drum speed during extraction G-factor, max. Heating: Electricity Heating: Steam Heating: Hot water Frequency of the dynamic force 15.2 14.3 Floor load at max extraction 3.4±0.5... -
Page 11: Setup
Installation manual 4 Setup 4.1 Unpacking Note! Two persons are recommended for the unpacking. The machine is delivered complete with expander bolts, supporting feet etc. The machine is delivered bolted onto the transport pallet and packed in a crate or box. Remove packing from the machine. -
Page 12: Unpacking For Machines Delivered On A Base
Installation manual 4.1.1 Unpacking for machines delivered on a base The machine is delivered complete with expander bolts, supporting feet etc. The machine is delivered bolted onto the transport pallet and packed in a crate or box. The machine is also delivered with cover panels that shall be used when the machine is delivered on a base. The cover panels and all additional equipment are placed at the rear of the machine (A). - Page 13 Installation manual Remove the front and rear panel. Remove the bolts between the machine and pallet. There is one to the right in the front of the machine and another diagonally opposed to it, at the back of the machine. fig.7651 Mount the supporting feet.
- Page 14 Installation manual Mount the cover panels Mount the screws and the plastic rings (delivered in a plastic bag) on the panels before mounting them on the machine. fig.W00218 The screws on the side panels (A) shall not be tightened all the way in. Make sure the machine is in level before mounting the front cover panel.
- Page 15 Installation manual The holes on the rear cover panel shall be placed on the screws (A) on the side cover panels and downwards in the holes. Tighten the screws. fig.6940 Place the machine on its final position.
-
Page 16: Recycling Instruction For Packaging
Installation manual 4.1.2 Recycling instruction for packaging fig.X02422 Fig. Description Code Type Wrapping film LDPE 4 Plastics Screw FE 40 Steel Packaging FOR 50 Wood Pallet FOR 50 Wood Screw FE 40 Steel Washer FE 40 Steel Plastic bag PET 1 Plastics... -
Page 17: Siting
If the machine is not to be mounted on a base the machine must be fastened to the floor. The table shows the correct drilling points. Mark and drill two holes (⌀ 10 mm) about 50 mm deep in the positions shown. fig.6943 WB5130H Standard Machine with Machine... -
Page 18: Water Connection
All connectors present on the machine must be connected. The table shows the possible connection options, which will depend on the water types to be connected to the machine. Information is also available on the panel above the connections. Water type Water connection WB5130H WB5130H • Cold and hot 1. Cold 2. Hot... -
Page 19: Connection Of External Dosing Systems
Installation manual 6 Connection of external dosing systems 6.1 Connection of the hoses The machine is prepared for connection of external dosing systems or water re-use systems etc. The connections are closed at delivery. Open any of the connections that shall be used by drilling a hole where the hoses shall be connected. -
Page 20: Machine With Connectors
Installation manual 6.2.1 Machine with connectors Connect the external dosing system to connections A and B on the machine. Connect the signal cable to B and the power supply to A. For Efficient dosing system the cables are delivered with the machine. Connect the power supply cable to the machine A and the other end of the cable together with the cable from Effi- cient Dosing in a connection box or with plug and receptacle. -
Page 21: Machine Without Connectors
Installation manual 6.2.2 Machine without connectors Connect the external dosing system to the I/O board, which is located to the right of the incoming power supply. The I/O board has edge connectors for connecting external dosing systems. Edge connectors on the I/O board can be loosened for connecting cables. fig.6572 11 = N 18 = Program run... -
Page 22: Outputs
Installation manual 6.2.3 Outputs Connect the power supply (e.g. 24V DC) for the external liquid supplies to 9 and 10. If an internal power supply (from the machine) is being used, it can be taken from 1 (N) and connected to 9 and from 2 (L) and connected to 10. Max load on the outputs 0.5 A. -
Page 23: Inputs
Installation manual Compartment 1 Pre-wash Compartment 2, 4 Main wash Compartment 3 Last rinse Signal 1 Pre-wash Signal 2 Main wash Signal 3 Softener, last rinse Signal 5 Bleach, whitening 6.2.4 Inputs The signal level can be 5-24V DC/AC or 100- 240V AC. For 5-24V, the signal reference is connected to 3 and for 100-240V to 4. -
Page 24: Drain Connection
Installation manual 7 Drain connection Connect a 75 mm pipe or rubber hose to the machine’s drain pipe, ensuring a downward flow from the machine. Avoid sharp bends which may prevent proper draining. Two ways of drain are available for the machines: •... -
Page 25: Electrical Connections
Installation manual 8.2 Electrical connections WB5130H Heating alternative Main voltage Heating power Total power Recommended fuse Electric heated 200V 3 ~ 50/60 220–240V 1 ~ 50/60 10.9–13.0 11.2–13.2 220–240V 3 ~ 50/60 10.9–13.0 11.2–13.2 380–415V 3 ~ 50/60 4.0-4.8 4.3–5.0 380–415V 3 ~... -
Page 26: Three-Phase Connection
Installation manual 8.3.2 Three-phase connection Connect the earth, neutral and phase wires as shown. L2 L3 3N AC... -
Page 27: Functions For I/O-Cards
Installation manual 8.4 Functions for I/O-cards The electrical schematic can be one of the following: 8.4.1 Outputs for detergent signals and inputs for pause signals, "empty" signal (2D) fig.6314B... -
Page 28: Steam Connection
Installation manual 9 Steam connection Inlet pipes connected to the machine must be equipped with a manual shut-off valve to facilitate installation and servicing. The connection hose must be of type ISO/1307- 1983 or equivalent. Connection size at filter:DN 15 (BSP 1/2"). Demount the top panel (A). - Page 29 Installation manual Mount the hose with wires between steam valve and machine. Connect wires in the steam valve. Connect ground cable to the terminal ground connection. Connect the ”HEAT” cable connector to the ”HEAT” terminal on the I/O board. ”HEAT” fig.6604 Steam pressure required: •...
-
Page 30: At First Power Up
Installation manual 10 At first power up When the installation is complete and the power is connected for the first time you will be forced to make the following settings. When one setting is ready you will automatically enter the next one. •... -
Page 31: Disposal Information
Installation manual 12 Disposal information 12.1 Disposal of appliance at end of life Before disposing of the machine, make sure to carefully check its physical condition, and in particular any parts of the structure that can give or break during scrapping. The machine’s parts must be disposed of in a differentiated way, according to their different characteristics (e.g. - Page 32 Electrolux Professional AB 341 80 Ljungby, Sweden www.electroluxprofessional.com...
Need help?
Do you have a question about the WB5130H and is the answer not in the manual?
Questions and answers