Advertisement
Installation instructions
Select the best location
1
To avoid vibration and noise, make sure the unit is
installed securely an
2
Install the unit where the sunlight does not shine directly
on the unit.
If the unit receives direct sunlight, build an awning to
shade the cabinet.
3
There should be no obstacle, such as a fence or wall,
within 50cm from the back of the cabinet because it will
prevent heat radiation of the condensor.
Restriction of outside air will greatly reduce the cooling
and heating e ciency of the air conditioner.
4
Install the unit with rear angled down so as not to
leak condensed water into the room (about 3°~4°
angle with level).
5
Install the unit with its bottom portion 75~150cm above
th
oor level.
6
The power cord must be connected to an independent
circuit. The yellow/green wire must be grounded.
7
Based on calculations in compliance with AS60335.2.40
there is no minimum saf
the air conditioners described in this manual.
caution
All side louvers of the cabinet must remain exposed to the
outside of the structure.
Installation of the Housing
1
Remove the air conditioner from its packaging, remove
ing screws and slide the air conditioner out of its
housing (Refer to Installation Steps).
2
Prepare the hole in the wall so that the bottom of
the housing is well supported, the top has minimum
clearance and the air inlet louvers have clearance as
shown below in options A and B. Holes from the outside
through to the cavity should be sealed. The housing
should slope down towards the rear by about 3°~4° to
allow water formed during operation to drain.
3
Install the housing into the wall and secure. Ensure the
foam seals are not damaged. Flash, seal o
around the inside and outside to provide satisfactory
appearance and protection against the weather, insects
and rodents.
Note: Unit may be supported by a solid frame from below or
by a hanger from a solid overhead support.
10 installation instructions Kelvinator Air Conditioning
Note: unit may be supported by a
rmly.
Preferred method of installation into a timber
framed wall, partition or window.
oor area for the installation of
Study timber
frame
Timber frame
wall or partition
Alternative method of installation if external
support cannot be provided.
AIR IN
AIR IN
AIR IN
AIR OUT
100mm minimum
OPTION A
AIR IN
ll gaps
100mm minimum
OPTION A
Note: unit may be supported by a
solid frame from below or
by a hanger from a solid
overhead support.
Flash or seal around external
Wall frame or architrave
sturdy timber
Sturdy timber
frame all
frame all
Drain pan
around unit
round unit
Sturdy timber
External support
frame all
frame at balance
round unit
point of A/C
timber framed
Timber framed
Alternately, brackets
wall or partition
Wall or partition
as illustrated below
Timber framed
may be used.
Wall or partition
preferred method of installation into a timber
Preferred method of installation into a timber
framed wall, partition or window
framed wall, partition or window.
Installation of the unit into the housing
1
Slide the unit into the housing until it i
rear of the housing. Care is required to ensure the foam
sealing strips on the housing remain in position.
2
Connect the air conditioner to the power and position
excess cord length beneath the air conditioner base.
Flash or seal around external
Wall frame or architrave
3
Engage the chassi
housing rail and secure to the base with the
screws provided.
Ensure louvres
are entirely
4
Remove the front panel from it's carton and plastic bag
outside the wall
an
as per the Installation lnstruction.
5
Switch unit on. Check for operation of the unit and check
Drain pan
for vibration in the installation.
Steadying bracket
(one per side)
6
Fit the drain pan to the housing and run a drain line to a
Solid timber support
suitable location if required.
Study timber
frame
Installing the unit into the wall
Timber frame
wall or partition
Ensure clearance around the air conditioner meets the following:
Minimum 150mm above the air conditioner
Minimum 150mm on left and right side of the air conditioner
Alternative method of installation if external
Minimum 1,000mm in front of the air conditioner
support cannot be provided.
Minimum 500mm to rear of the air conditioner
45° brick cut away
45° brick cut away
to clear louvres
to clear louvres
utside)
ditioner
BR ICK
WALL
AIR IN
air in
louvre
Louvre
AIR IN
Fence or
likewise
AIR OUT
150mm
solid frame from below or
by a hanger from a solid
overhead support.
Flash or seal around external
ash or seal around external
Wall frame or architrave
wall frame of architrave
drain
Drain pan
External support
external support frame
frame at balance
at balance point of A/C
point of A/C
Alternately, brackets
as illustrated below
may be used.
xing brackets into the bottom
Flash or seal around external
Wall frame or architrave
Ensure louvres
are entirely
outside the wall
Drain pan
Steadying bracket
(one per side)
Solid timber support
45° brick cut away
45° brick cut away
to clear louvres
to clear louvres
Front
front
100mm
100mm
45° brick cut away
to clear louvres
TOP
VIEW
BR ICK
air out
AIR OUT
WALL
TOP VIEW
AIR IN
Over 500mm
Over
Over
150mm
rmly against the
BR ICK
WALL
air in
A
IR IN
100mm
100mm
10
TOP
VIEW
Louvre
AIR OUT
OPTION
Hide quick links:
Advertisement
