Congratulations Contents Congratulations and thank you for choosing our Inverter split Safety Instructions system room air conditioner. We are sure you will find Warnings ..................3 your new air conditioner a pleasure to use. Before you use the air conditioner, we recommend that you read through Product description the entire user manual, which provides the description of Installation drawing .................
Safety instructions Meanings of symbols used in this manual are shown below: warning WARNING • Do not use means to accelerate the defrosting process or to WARNING warning clean, other than those recommended by the manufacturer. This symbol indicates information concerning your personal safety or information on how to avoid damaging the air conditioner •...
Page 4
Safety instructions Troubleshooting warning WARNING You'll find many answers to common problems in the chart of troubleshooting tips on page 21. If you review the chart of • Do not place obstacles around air inlets or inside of Troubleshooting Tips first, you may not need to call for service. air outlet.
Installation drawing Fig. 1 Installation plate ng screw ST3.9x25(5) 15cm or more 12cm or more 12cm or more Remote control Air ter 200cm or more Additional drain pipe Before screwing the remote controller holder to the wall, make sure that control signals are properly received by Wrapping tape (wrap the indoor unit.
Remote control speci cations Using the remote control Rated voltage 3.0V (2x 1.5V AAA) Signal receiving range Location of the remote controller • Use the remote controller within a distance of 8 meters from the appliance, pointing it towards the receiver. Reception is con rmed by a beep.
Indoor unit display Digital display • Displays the temperature settings when the air conditioner is operational. Replacing batteries • Displays the room temperature in FAN mode. • Displays the self-diagnostic codes. The following cases signify exhausted batteries. Replace old batteries with new ones. •...
Page 8
Operation of buttons ON/OFF Button This button turns the air conditioner ON and OFF. Mode Button Press this button to modify the air conditioner mode in a sequence of following: AUTO > COOL > DRY > HEAT > FAN NOTE: Please do not select HEAT mode if the machine you purchased is cooling only type.
Page 9
Operation of buttons Button ( + ) Push this button to increase the indoor temperature setting in 1°C increments to 30°C. DOWN Button ( - ) Push this button to decrease the indoor temperature setting in 1°C increments to 17°C. an/quiet B •...
Indicators on LCD Information are displayed when the remote controller is Mode display powered up. AUTO COOL HEAT Icon Function Displayed when data transmitted Displayed when remote controller is ON Battery display (low battery detection) Displayed when TIMER ON time is set Displayed when TIMER OFF time is set Show set temperature or room temperature, or time under TIMER setting...
How to use the buttons NOTE: In the FAN mode, the setting temperature is not displayed in the remote controller and you are not able to control the room temperature either. In this case, only step 1, 3 and 4 may be performed.
Timer operation caution WARNING • When you select the timer operation, the remote controller automatically transmits the timer signal to the indoor unit for Mode ON/OFF the speci ed time. Therefore, keep the remote controller in Quiet a location where it can transmit the signal to the indoor unit properly.
Page 13
Examples of timer operation Timer on (Auto-on Operation) Combined timer (Setting both ON and OFF timers simultaneously) Timer off/Timer on (On/Stop/Start operation) Start 6 hours later The Timer On feature is useful when you want the unit to turn 2 hours later 10 hours later on automatically before you return home.
But it restarts automatically and performs previous operation when the power supply is resumed. Visit the Apple App Store or the Google Play Store and download the "Kelvinator Home Comfort" app on your smart phone to connect and control your air conditioner remotely. Kelvinator...
Airflow directional control The direction of airflow can be adjusted for maximum comfort. caution WARNING • Do not operate the air conditioner for long periods with the air flow direction set downward in cooling or dehumidifying mode. Otherwise, condensation may occur on the surface of the horizontal louver causing moisture to drop on to the floor or on furnishings.
Page 16
Operating temperature Manual operation Mode Temperature Cooling operation Heating operation Room temperature 17°C – 32°C 0°C – 30°C caution Outdoor temperature 0°C – 50°C -15°C – 30°C • This switch is used for testing purposes only. Please do not use it unless necessary.
Care and maintenance Before maintenance • Turn the system off before cleaning. To clean, wipe with a soft, dry cloth. Do not use bleach or abrasives. NOTE: Power supply must be disconnected before attempting to clean or service. warning WARNING Servicing shall only be performed as recommended by the equipment manufacturer.
Care and maintenance After the filters are dry, refit the small filters onto the large air filter. Re-insert the filters back into the unit following the reverse order as described in steps 1 & 2. Close the front panel. Make sure the buckles are fully fit and the panel is completely closed.
Troubleshooting Troubleshooting tips The following events may occur during normal operation, and may not indicate malfunction Symptom Cause Operation is delayed after restart To prevent blowout of the fuse, the compressor will not operate while the protection circuit is working for about 3 minutes after sudden OFF/ON operation of the power supply, this is normal operation and designed to protect the compressor.
Page 20
Troubleshooting Before you call for or request servicing, troubleshoot a problem by performing following checks: Symptom Diagnostic Is there a power failure? Has a switch been turned off, a circuit breaker tripped or a fuse blown? Unit will not operate Is the timer operating? Are the batteries used in the remote controller exhausted? Are the batteries used in the remote controller loaded properly?