Table of Contents
Advertisement
Maintenance, inspections, checks and cleaning
Preventive maintenance
• check all gas components (if present).
Preventive maintenance
• remove any deposits of dirt inside the appliance.
Control
• check the conditions of the internal parts.
Control
• check and clean the discharge system.
General machine overhaul
• check all components, electrical equipment, corrosion, pipes...
1.
In particular conditions (e. g. intensive use of the appliance, salty environment, etc.) the preventive maintenance should be more frequent.
2.
the machine is designed and built for a duration of about 10 years. After this period of time (from commissioning) the machine must undergo a general
inspection and overhaul. Some examples of checks to be carried out are given below.
• Check for any oxidised electrical components or parts; if necessary, replace them and restore the initial conditions;
• Check the structure and welded joints in particular;
• Check and replace bolts and/or screws, also checking for any loose components;
• Check the electrical and electronic system;
• Check the functionality of safety devices;
• Check the general condition of protection devices and guards.
NOTE!
It is advisable to stipulate a preventive and scheduled maintenance contract with the Customer Care Service.
Disassembly
• All scrapping operations must occur with the machine stopped and cold and the electrical power supply disconnected;
• Work on the electrical equipment must only be carried out by a qualified electrician, with the power supply disconnected;
• To carry out these operations it is necessary to use: overalls, safety shoes and gloves;
• During disassembly and handling of the various parts, the minimum height from the floor must be maintained.
G.5
Maintenance contacts (only for Australia)
For service and spare parts, please contact:
• Electrolux - Tom Stoddart Pty Ltd — 39 Forest Way,
Karawatha QLD 4117 — call 1-300-307-289
H
MACHINE DISPOSAL
WARNING
Refer to "Safety Information"
H.1
Waste storage
At the end of the product's life-cycle, make sure it is not
dispersed in the environment. The doors must be removed
before scrapping the appliance.
SPECIAL waste materials can be stored temporarily while
awaiting treatment for disposal and/or permanent storage. In
any case, the current environmental protection laws in the
user's country must be observed.
H.2
Procedure regarding appliance dismantling
macro operations
Before disposing of the machine, make sure to carefully check
its physical condition, and in particular any parts of the
structure that can give or break during scrapping.
The machine's parts must be disposed of in a differentiated
way, according to their different characteristics (e. g. metals,
oils, greases, plastic, rubber, etc.).
Different regulations are in force in the various countries,
therefore comply with the provisions of the laws and compe-
tent bodies in the country where scrapping takes place.
I
ENCLOSED DOCUMENTS
• Set of test and inspection documents.
• Wiring diagram.
Frequency
Yearly
1
Every 6 months
1
Every 6 months
1
Every 6 months
2
Every 10 years
• Zanussi - Procook Australia Pty Ltd — 23 Rothesay Street,
Kenmore, Queensland 4069 — call 07-3868-4964
• Diamond - Semak Food Service Equipment — 18, 87– 91
Hallam South Road, Hallam VIC 3803 — call 03-9796-4583
In general, the appliance must be taken to a specialised
collection/ scrapping centre.
Dismantle the appliance, grouping the components according
to their chemical characteristics, remembering that the com-
pressor contains lubricant oil and refrigerant fluid which can be
recycled, and that the refrigerator components are special
waste assimilable with urban waste.
The symbol on the product indicates that this
product should not be treated as domestic
waste, but must be correctly disposed of in
order to prevent any negative consequences
for the environment and human health. For
further information on the recycling of this
product, contact the local dealer or agent, the
Customer Care service or the local body
responsible for waste disposal.
NOTE!
When scrapping the machine, any marking, this
manual and other documents concerning the appli-
ance must be destroyed.
• Installation diagram.
Responsibility
Service
Service
Service
Service
Service
23
Advertisement
Table of Contents
