Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Calculated Industries PIPE TRADES PRO 4095
Summary of Contents for Calculated Industries PIPE TRADES PRO 4095
- Page 2 PlumbingCalc Pro™ Flow & Dimensional Math Calculator could not have been done without the support of pipefitting and plumbing professionals. Calculated Industries gratefully acknowledges the many individuals and organizations who were so generous with their time and expertise.
-
Page 3: Table Of Contents
PiPe Trades Pro Table of conTenTs ™ The Pipe Trades Pro™ Advanced Pipe GETTING STARTED ........5 Trades Math Calculator has been specifically KEY DEFINITIONS ........5 designed for today’s pipe trade professionals. No matter what Pipe Trade you work in, you'll Basic Function Keys ........ -
Page 4: Getting Started
Simple Offset - Unknown Bend Angle ..24 GeTTinG sTarTed Simple Offset - Cut Length ...... 25 You may want to practice getting a feel for Rolling Offset - Known Bend Angle ..27 your calculator keys by reading through the key definitions and learning how to enter basic Rolling Offset - Unknown Bend Angle .. -
Page 5: Dimensional Function Keys
(cont'd) fractional and decimal inches. Store – Used for storing values. Fraction Bar – Used to enter fractions. Fractions can be Recall – Used with other keys to entered as proper (1/2, 1/8, recall stored values and settings. 1/16) or improper (3/2, 9/8). If the denominator (bottom) is not ... -
Page 6: Weight/Volume Functions
Circle Key (cont'd) Millimeters – Enters or converts to Circle – Enters diameter and millimeters. calculates circle area and circumference. Meters (m) – Enters or converts to meters. Trigonometric Keys Gallons – Enters or converts to Sine –... -
Page 7: Pipefitting Project Keys
Pipefitting Project Keys Take-Out (T.O./Arc) – Used to enter or solve fitting Take-Outs when calculating pipe cut lengths. Slope Calculates inner, center, and outer arc lengths for marking field cut fittings. Offset – Calculates or enters the Travel Offset (Rise). -
Page 8: Miscellaneous Functions
Miscellaneous Functions (cont'd) Pipe Type – Defines the Pipe Type based on Pipe Material. Open parenthesis key. Cutback – Calculates pipe Cutback Close parenthesis key. after Bend Angle and Offset are – Enters an exponential value entered. -
Page 9: Preference Settings
(cont'd) Enter the Preference Mode by pressing Store unit cost. (Prefs). Access each category by pressing the key until you reach the Degrees:Minutes:Seconds desired setting. Within each category, press (dms◄►deg) – Converts between the ... -
Page 10: Percentage Calculations
(cont'd) Sixth press of (Fractional mode) FRAC Std. KEYSTROKE DISPLAY FRAC COnSt. FRAC 0-1/32 INCH FRAC Std. FRAC 0-1/64 INCH (repeats options) FRAC 0-1/2 INCH FRAC 0-1/4 INCH Seventh press of FRAC 0-1/8 INCH (Mathematical Operation) MATH OrdEr ... -
Page 11: Memory Operation
Using M+ (cont'd) KEYSTROKE DISPLAY KEYSTROKE DISPLAY M+ 355. 229 FEET 2-3/8 INCH (%) M+ 255. (M-) M- 745. 7 ... -
Page 12: Pipe Size Key
(cont'd) KEYSTROKE DISPLAY KEYSTROKE DISPLAY MATL COPPEr (Copper) MATL PLAStIC (Pipe Type) TYPE 80 PLAStIC The last material setting displayed is selected, and the calculator will retain your Pipe Size Key setting even after the power has been turned off. -
Page 13: Elbow Type
2593-4095 PipeSizeErrorStickers_1.75x1.75.eps (cont'd) elbow fittings can have a different Take-Out calculation from the field cut variants. KEYSTROKE DISPLAY (Filled Weight/Foot) FILL SIZE 13.11634 LB PER FEET This function toggles the Elbow types AREA SIZE 6.605199 SQ INCH (Internal Area) between the following options: Butt Weld –... -
Page 14: Simple Offset - Known Bend Angle
(cont'd) KEYSTROKE DISPLAY KEYSTROKE DISPLAY 1. Enter Offset: OFST 16 INCH (Default) BW-L EL. tYPE 1 6 BW-S EL. tYPE 2. Enter Run: FC-L EL. tYPE RUN 27 INCH 2 7 FC-S EL. tYPE 3. Find the pipe length: BW-L EL. -
Page 15: Rolling Offset - Known Bend Angle
(cont'd) Note: To return the Welder’s Gap to the default 1/8”, press KEYSTROKE DISPLAY to reset your calculator back to default values. 1. Select Stainless Steel: MATL S.StEEL Rolling Offset – Known Bend Angle 2. Enter Pipe Size: 40 SIZE 6 INCH 6 Find the center-to-center travel for a rolling pipe offset with a 4” Roll and a 24” Offset. 3. Enter 0 for Welder's Gap: (Welder's Gap) GAP 0 INCH... -
Page 16: Rolling Offset - Cut Length
(cont'd) KEYSTROKE DISPLAY KEYSTROKE DISPLAY 1. Enter Offset: 1. Enter Pipe Size: OFST 17 INCH STD SIZE 6 INCH 1 7 6 2. Enter the advance: 2. Change the default Welder’s Gap from 2 (Advance) RUN 28 INCH 1/8” to 3/32”: 3. Enter the Roll and calculate the pipe * GAP 0-3/32 INCH 2 length and unknown bend angle: 3. Enter Offset: 6 ... -
Page 17: Concentric Pipe Bend Cutback
Calculate Take-Out and (cont'd) fractional resolution (default is 1/16) press Butt Weld Elbow Cut Marks once after entering the welder's gap. For example, if you keep the fractional The Take-Out function can be used to quickly resolution at 1/16, the outputs above for solve a Take-Out and butt weld elbow cut IARC would be 4 inches, and CARC would marks for a known bend angle and Pipe Size. be 6-3/8 inches. -
Page 18: Cut Length - Known Take-Out Value
Cut Length – Known Take-Out Value KEYSTROKE DISPLAY 6. Enter 0 for Welder’s Gap: The Pipe Trades Pro can solve cut lengths GAP 0 INCH (Welder's Gap) for materials and fittings not currently built 7. Find the pipe cut length: into the calculator by entering a known Take- TRAV 14-1/8 INCH ... -
Page 19: Weight Of Filled Pipe
(cont'd) KEYSTROKE DISPLAY KEYSTROKE DISPLAY 2. Calculate the total drop (Offset): 2. Choose the Pipe Type: (Pipe Type) TYPE 5 S.StEEL 2 5 OFST 0 FEET 3-1/8 INCH 3. Enter the Pipe Size: 5 SIZE 6 INCH Find the slope of a pipe Run if it drops 6 inches over 50 feet. What is its Angle and 4. Find the weight of one foot of water-filled pipe: Percent Grade? (6 times) FILL SIZE 21.71418 LB PER FEET KEYSTROKE DISPLAY 5. Find the weight of the filled 10' length of pipe:... -
Page 20: Circle Area And Circumference
Circle Area and Circumference any operator key is pressed. For example, 30° 89’ entered will be corrected and dis- Find the area and circumference of a circle played at 31° 29’ 0” or 31.48°. with a diameter of 25 Inches: KEYSTROKE DISPLAY Trigonometric Functions Trigonometric functions are available on the DIA 25 INCH 2 5 Pipe Trades Pro calculator. -
Page 21: Appendix
Replacement batteries are available at most Angle b A C discount or electronics stores. You may also Given side B and angle b, find: call Calculated Industries at 1-775-885-4900. Side C B b Battery Replacement Instructions Side A B b ... - Page 22 Construction Master Technologies, LLC, 2009. Pocket Reference Guide copyrighted by Calculated Industries, Inc. © 2009. Pipe Trades Pro™ is a trademark and Calculated Industries® is a registered trademark of Calculated Industries, Inc. ALL RIGHTS RESERVED CALCULATED INDUSTRIES® 4840 Hytech Drive Carson City, NV 89706 U.S.A.
- Page 23 For more information regarding Warranty, Repair and Return, see the full User's Guide.
Need help?
Do you have a question about the PIPE TRADES PRO 4095 and is the answer not in the manual?
Questions and answers