SHOEI GT-Air II Instruction Manual
Hide thumbs Also See for GT-Air II:

Advertisement

Instructions for use
Thank you for purchasing your new SHOEI helmet. This manual contains valuable information to help you understand how to
operate and maintain your helmet. Please read this manual carefully before use and keep it for future reference. Your SHOEI
dealer can provide a replacement if this manual is lost.
Read This First
Confirm the Packed Items
Parts Description
Breath Guard
Applying Silicone Oil
Chin Curtain
CNS-1 Shield / Visor
Important Notice about Handling
the CNS-1 Shield / Visor
Adjustment
of the CNS-1 Shield/Visor
QSV-2 Sun Visor
Important Notice about Handling
the QSV-2 Sun Visor
PINLOCK
EVO lens
®
Service Tool
Replacing Interior Parts
Removing Interior Parts
Ear Pads
Installing Interior Parts
Important Notice about
Handling Interior Parts
When Installing the Intercom
E.Q.R.S.
(Emergency Quick Release System)
WARNING
Parts List

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GT-Air II and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for SHOEI GT-Air II

  • Page 1 Thank you for purchasing your new SHOEI helmet. This manual contains valuable information to help you understand how to Breath Guard operate and maintain your helmet. Please read this manual carefully before use and keep it for future reference. Your SHOEI dealer can provide a replacement if this manual is lost.
  • Page 2: Read This First

    The contents of this manual are subject to change without notice. The illustrations in this manual may differ from the actual product. The copyrights for this manual belong to SHOEI CO., LTD. Reproduction or copying of this manual without written permission is strictly prohibited. HOW TO USE...
  • Page 3: Parts Description

    Breath Guard Parts Description 1. Lower Air Intake The breath guard reduces fogging of the 2. Defogger Ventilation System shield/visor caused by breathing. 3. Sun Shield / Visor Lock Lever To install the breath guard, use the following 4. CNS-1 Shield / Visor procedure.
  • Page 4: Chin Curtain

    Chin Curtain CNS-1 Shield / Visor The chin curtain reduces the influx of air turbulence and wind noise Before using the shield / visor for the first time after purchase, remove protective film from into the helmet’s chin area. The chin curtain is detachable. The chin shield / visor.
  • Page 5 / visor. Use of the PINLOCK © Hook (A) lens is also effective in stopping fog. 4. Always use SHOEI’s genuine PINLOCK 8. Do not place any sticker or tape in the © lens for CNS-1. For fitting PINLOCK shield’s / visor’s field of vision.
  • Page 6 Left side Adjustment of the CNS-1 Shield/Visor QSV-2 Sun Visor QSV-2 sun visor can be opened and closed as the lock levers for ❶ Align the center of the hole in the lower base plate with the sun visor on both sides are in downed position (Drawing 1). center of the lower screw hole (Drawing 1) and tighten the Do not pull the levers up except when removing and installing the sun Base Plate...
  • Page 7 Important Notice about Handling the QSV-2 Sun Visor ■ Installing the QSV-2 Sun Visor Lock Lever 1. Make sure the lock levers for the sun visor are in downed position. In case, the lock levers are in pulled-up position, 1. Only raise or lower the sun visor by 7.
  • Page 8: Pinlock ® Evo Lens

    PINLOCK EVO lens ® If you are using the PINLOCK * EVO lens, ® read the instruction manual that comes packed with it. 1. Daytime use only. Never use PINLOCK ® EVO lens at night. If the PINLOCK ® lens is used with a clear shield/visor, its light transmission ratio will be approximately 80%.
  • Page 9: Replacing Interior Parts

    Front Avant Removing Interior Parts Replacing Interior Parts Hook Crochet 1. Removing the Cheek Pads Unfasten the 3 snaps to remove the pad from the cheek pad base (Drawing 1), and pull the Rear notch (a) from the cheek pad bracket (A) Center Pad Arrière (Drawing 2).
  • Page 10 Chinstrap Installing Interior Parts 3. Removing the Center Pad Chinstrap Cover Remove the center pad by unsnapping 2 snaps at the rear of the helmet first (Drawing 5), and 1. Installing the Chinstrap Covers pull the front portion of the center pad from A chinstrap is interchangeable right and left.
  • Page 11 If the impact absorbing liner is exposed to high heat of any kind, contact your dealer or SHOEI directly for a safety evaluation. To prevent damage, do not use any of the following cleaning materials: hot water over 40°C;...
  • Page 12: When Installing The Intercom

    (Drawing 2). cover equipped. Slide the cover up onto the base in the direction of the Be sure to use SHOEI recommended intercom exclusively arrow shown. ● designed GT-Air Ⅱ.
  • Page 13: Parts List

    ● Breath Guard 2. Use genuine SHOEI cheek pads only and 5. Be sure to use SHOEI genuine parts when never use non-SHOEI parts. ● Center Pad replacing the shield/visor, sun visor, or inner ●...

Table of Contents

Save PDF