Table of Contents
Advertisement
MAINTENANCE (cont.)
Cleaning & Storing
• Keep the handles free of grease and oil so that you can maintain a firm
grip.
• Clean the device as required with a damp cloth and, if necessary, mild
washing up liquid.
• If the chainsaw is not to be used for an extended period of time then you
should remove the chain bar oil from the tank. Briefly immerse the chain
and the guide bar in an oil bath and then wrap them in oil paper and
store in guide bar cover.
Ozito Industries will not be responsible for any damage or injuries caused by
repair of the tool by an unauthorised person or mishandling or mistreatment
of the tool. This tool is designed for Domestic Home Use only. Use in
commercial or industrial environments will void the warranty.
SPARE PARTS
Chain Replacement
The chain can be purchased through Ozito spare parts or from your local
Bunnings Warehouse. The correct chain can be purchased by matching
the pitch, gauge and number of links as shown below:
2
9.53mm (3/8")
1.3mm (.050")
Spare parts can be ordered from the Special Orders Desk at your
local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito Customer Service:
Australia 1800 069 486
New Zealand 0508 069 486
E-mail: enquiries@ozito.com.au
DESCRIPTION OF SYMBOLS
V
Volts
~
Alternating Current
Revolutions or reciprocations
/min
per minute
Double insulated
Ø
Diameter
Regulatory Compliance Mark
(RCM)
Disconnect and discontinue use
should the power cord be
damaged.
Read Instruction Manual
Sound power level
108
IMPORTANT! When placing the chain on the guide bar,
ensure the chain direction is the same as the image on the
guide bar
52 Links
Gauge
Hz
Hertz
W
Watts
n
No load speed
0
Wear hearing & eye protection
Wear non-slip heavy duty gloves
Warning
Beware of kickback
Do not expose to rain
Always hold the chainsaw with
both hands
52
Chain drive links 52
TROUBLESHOOTING
PROBLEM
Chainsaw will not
work.
30º
Chainsaw operates
intermittently
outward
Dry chain
stroke
Chain or guide rail
hot
Wont cut
Chainsaw vibrating
or not cutting
properly
CARING FOR THE ENVIRONMENT
Power tools that are no longer usable should not
be disposed of with household waste but in an
environmentally friendly way. Please recycle where
facilities exist. Check with your local council authority for
recycling advice.
Recycling packaging reduces the need for landfill and
raw materials. Reuse of recycled material decreases
pollution in the environment. Please recycle packaging
where facilities exist. Check with your local council
authority for recycling advice.
CAUSE
REMEDY
Chain brake
Disengage brake
1
engaged
No power supply
Try alternative
source of electrical
power
Defective mains
Try alternative
outlet
source of electrical
power
Power extension
Check the cable and
cord damaged
replace if required
Power cable
Replace power cable
damaged
On/Off switch
Replace switch
defective
No oil in oil tank
Fill oil tank with
chain bar oil
Oil tank cap breather
Clean oil tank cap
blocked
Oil outlet blocked
Clear oil outlet
No oil in oil tank
Fill oil tank with
chain bar oil
Oil tank cap breather
Clean oil tank cap
blocked
Oil outlet blocked
Clear oil outlet
Blunt chain
Sharpen or replace
chain
Blunt chain
Sharpen or replace
chain
Chain on backwards
Remove chain and
(chain teeth pointing
reinstall with the
in the wrong
teeth facing in the
direction)
correct direction
Worn chain
Replace the chain
Chain tension too
Adjust chain to
loose
correct tension
Blunt chain
Sharpen or replace
chain
Worn chain
Replace the chain
Chain on backwards
Remove chain and
(chain teeth pointing
reinstall with the
in the wrong
teeth facing in the
direction).
correct direction
2
Advertisement
Table of Contents
