About Cddi On/Off Of Digital Input; About Vsiox1 - Toshiba TOSDIC-CIE DS Manual

Appendix2. The diffrence between DPCS and DPCS Emulator
Table A2.11 Conversion table of VAMPX1+VAINX1B, and SAI01

About CDDI On/Off of digital input

When using VDINX2, there is a function which hold digital input signal for a fixed time. When using
this CDDI function, CDDI ON data and CDDI OFF data of SDI01 or SDIF1 are used. In the engineering
(MC bus SI/O mapping) which assigns a Serial I/O module to a DPCS card, the bus number, the unit
number, module number, and point number of a Serial I/O module are specified. When using CDDI data,
about a bus number, a unit number, and a module number, the value of a place of SDI01 or SDIF1
module is inputted. CDDI ON and CDDI OFF are inputted by the point number. In the case of DI signal,
input 1 to the point number. In the case of CDDI ON, input 33 to the point number. In the case of CDDI
OFF, input 65 to the point number. Each data of SDI01 or SDIF1 module can be treated as an input value
of a DPCS card. The holding time of CDDI is registered in the I/O module information on SDI01 or
SDIF1 module. When you use SDI01, you use the SBIF1C module.

About VSIOX1

In VSIOX1, SSIF is registered at Serial I/O module configuration. When Serial I/O module classification
of digital input/output cards, such as VDINX1, is SSIF1, DPCS emulator recognizes that it is VSIOX1.
In the engineering (MC bus SI/O mapping) which assigns a Serial I/O module to a DPCS card, the bus
number, the unit number, module number, and point number of a Serial I/O module are specified. Input
the value of a place of SSIF1 module to a bus number and a unit number. Input receiving / transmitting
block number of SSIF1 to a module number. (The receiving block 0 and the transmitting block 0 are not
used) Input the position in a block to a point number. (It inputs from 1 to 26 that is the word position.)
When you input and output analog data, please register the Serial I/O module SSIF1 to VPCPX2 card.
The number of maximum blocks of input / output of analog data in VSIOX is 4. Although the registration
52
VAMPX1+VAINX1B
Input range (V) BIAS
-5.00 --- +5.00 0
-1.00 --- +1.00 0
-0.20 --- +0.20 0
-0.10 --- +0.10 0
-0.05 --- +0.05 0
-0.04 --- +0.04 0
-0.02 --- +0.02 0
-0.01 --- +0.01 0
1.00 --- +5.00 1
0.00 --- +1.00 1
0.00 --- +0.20 1
0.00 --- +0.10 1
0.00 --- +0.05 1
0.00 --- +0.04 1
0.00 --- +0.02 1
0.00 --- +0.01 1
SAI01
LEVEL Input range (V)
0 -5.00 --- +5.00
1 -1.00 --- +1.00
2 -1.00 --- +1.00
3 -0.10 --- +0.10
4 -0.05 --- +0.05
5 -0.05 --- +0.05
6 -0.02 --- +0.02
7 -0.01 --- +0.01
0 -5.00 --- +5.00
1 -1.00 --- +1.00
2 -1.00 --- +1.00
3 -0.10 --- +0.10
4 -0.05 --- +0.05
5 -0.05 --- +0.05
6 -0.02 --- +0.02
7 -0.01 --- +0.01