Advertisement
Access & Power Integration
T1RM3F4
Fully assembled kit includes:
- Trove1R rack enclosure with Altronix/Mercury backplane (TM1R)
- (1) eFlow6NB - Power Supply/Charger
- (1) VR6 - Voltage Regulator
- (1) PDS8 - Fused Dual Output Power Distribution Module
- (1) ACM4 - Fused Access Power Controller
T1RM3F4D
Fully assembled kit includes:
- Trove1R rack enclosure with Altronix/Mercury backplane (TM1R)
- (1) eFlow6NB - Power Supply/Charger
- (1) VR6 - Voltage Regulator
- (1) PDS8CB - PTC Dual Output Power Distribution Module
- (1) ACM4CB - PTC Access Power Controller
Installation Guide
All registered trademarks are property of their respective owners.
Rev. T1RM3F4080720
Installing Company: _____________________ Service Rep. Name: __________________________________________
Address: ________________________________________________________ Phone #: _________________________
More than just power.™
Advertisement
Table of Contents
Related Manuals for Altronix TROVE T1RM3F4
Summary of Contents for Altronix TROVE T1RM3F4
- Page 1 Access & Power Integration T1RM3F4 Fully assembled kit includes: - Trove1R rack enclosure with Altronix/Mercury backplane (TM1R) - (1) eFlow6NB - Power Supply/Charger - (1) VR6 - Voltage Regulator - (1) PDS8 - Fused Dual Output Power Distribution Module - (1) ACM4 - Fused Access Power Controller...
-
Page 2: Configuration Chart
Altronix T1RM3F4 and T1RM3F4D rack kits are pre-assembled and consist of Trove1M1R enclosure/backplane with factory installed Altronix power supply/charger and sub-assemblies. These kits also accommodate various combinations of Mercury boards for up to four (4) doors in a single enclosure. -
Page 3: Hardware Included
Assembling and Attaching Z Bracket Wire Management Accessory (included): Altronix Trove Rack enclosures include Z Bracket, a convenient and reliable wire management accessory. 1. Carefully unpack Z Bracket. Do not discard hardware (included) (Fig. 1, pg. 3). 2. Attach arms to each other using bolts and lock nuts (Fig. 1a, pg. 3). - Page 4 1. Remove backplane from enclosure prior to installing into rack cabinet (do not discard hardware). 2. In order to mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) turn the enclosure upside down. Punch out the knockout in designated location, on the back of the unit, from outside of the drawer (Fig. 3, pg. 4).
- Page 5 T1RM3F4(D): Configuration of Mercury Boards: 1. Fasten spacers onto metal pems configuration (A), (B), (C) or (D) of backplane depending on the access controller (Fig. 4, pg. 5). 2. Position access controller module over corresponding spacers and fasten screws into spacers (Fig. 4a, pg. 5). 3.
- Page 6 Notes: - 6 - T1RM3F4(D)
- Page 7 Notes: T1RM3F4(D) - 7 -...
- Page 8 3.25” 82.3mm Altronix is not responsible for any typographical errors. 140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056 web site: www.altronix.com | e-mail: info@altronix.com | Made in U.S.A. IIT1RM3F4(D) H20T MEMBER - 8 -...
Need help?
Do you have a question about the TROVE T1RM3F4 and is the answer not in the manual?
Questions and answers