Table of Contents
Advertisement
Quick Links
29. May 2001
Function Description
Function Description
Function Description
Function Description
S S S S
a a a a
f f f f
e e e e
t t t t
y y y y
L L L L
i i i i
S S S S
a a a a
f f f f
e e e e
t t t t
y y y y
L L L L
i i i i
No. ST2-015031A
g g g g
h h h h
t t t t
C C C C
u u u u
r r r r
t t t t
a a a a
i i i i
n n n n
g g g g
h h h h
t t t t
C C C C
u u u u
r r r r
t t t t
a a a a
i i i i
n n n n
F3SN
F3SN
F3SN
F3SN
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Omron F3SN
Summary of Contents for Omron F3SN
- Page 1 C C C C u u u u r r r r t t t t a a a a i i i i n n n n F3SN F3SN F3SN F3SN...
-
Page 2: Table Of Contents
F3SN F3SN F3SN F3SN Function Description Function Description Function Description Function Description Index 1. Functions ............................3 1.1. External test function ....................... 3 1.2. Interlock function ......................4 1.2.1. Manual reset mode / Auto reset mode................4 1.2.2. Start interlock........................ 5 1.2.3. -
Page 3: Functions
This function stops light emission of an emitter. It is available for checking if the F3SN can show the correct OSSD (Output Signal Switching Device) outputs state, and so on. [Directions for use] Applying a voltage of 24VDC (for PNP type) or 0 V (for NPN type) to the test input line of an emitter makes the emitter stop emitting. -
Page 4: Interlock Function
These modes are wire selectable features of the F3SN. When the F3SN is set as “Start interlock valid” and/or “Restart interlock valid” and the wir- ing corresponds to “Manual reset mode”, the interlock function(s) are available. For the fac- tory setting, both the start interlock and the restart interlock are set valid. -
Page 5: Start Interlock
F F F F 3 3 3 3 S S S S N N N N F F F F 3 3 3 3 S S S S N N N N Safety Light Curtain Safety Light Curtain Safety Light Curtain Safety Light Curtain s s s s e e e e... -
Page 6: Restart Interlock
F F F F 3 3 3 3 S S S S N N N N F F F F 3 3 3 3 S S S S N N N N Safety Light Curtain Safety Light Curtain Safety Light Curtain Safety Light Curtain s s s s e e e e... -
Page 7: Blanking Function
Note 2: There is no limit for the number of fixed blanked beams. Note 3: The fixed blanking function is set invalid when the F3SN is shipped. Note 4: Series connection The validity of the fixed blanking depends on the setting of the 1CH sensor, which is the closest to power supply. -
Page 8: Floating Blanking
F F F F 3 3 3 3 S S S S N N N N F F F F 3 3 3 3 S S S S N N N N Safety Light Curtain Safety Light Curtain Safety Light Curtain Safety Light Curtain s s s s e e e e... - Page 9 (All relating to the floating blanking function are set invalid, OFF, or Clear when the F3SN is shipped.) Note 2: When an outermost beam is blanked by the fixed blanking function, the outermost beam invalid mode cannot be available.
- Page 10 F F F F 3 3 3 3 S S S S N N N N F F F F 3 3 3 3 S S S S N N N N Safety Light Curtain Safety Light Curtain Safety Light Curtain Safety Light Curtain s s s s e e e e...
-
Page 11: External Device Monitoring (Edm)
Note 1: When the OSSD outputs change over within the determination time after their previous changeover, the F3SN does not enter the lock-out condition even if the logic at the EDM input does not change over. -
Page 12: Auxiliary Output Function
F F F F 3 3 3 3 S S S S N N N N F F F F 3 3 3 3 S S S S N N N N Safety Light Curtain Safety Light Curtain Safety Light Curtain Safety Light Curtain s s s s e e e e... -
Page 13: Outermost-Beam Monitoring Mode
: ON OFF response time of OSSD outputs 1.5.4. Lockout mode When the F3SN enters lockout condition, the auxiliary output goes to the ON-state. Response time OFF ON : Max. 100ms after the F3SN detects a fault. Timing chart of the Lockout mode... -
Page 14: Light Diagnosis Mode
F F F F 3 3 3 3 S S S S N N N N F F F F 3 3 3 3 S S S S N N N N Safety Light Curtain Safety Light Curtain Safety Light Curtain Safety Light Curtain s s s s e e e e... -
Page 15: Blanking Monitoring Mode
F F F F 3 3 3 3 S S S S N N N N F F F F 3 3 3 3 S S S S N N N N Safety Light Curtain Safety Light Curtain Safety Light Curtain Safety Light Curtain s s s s e e e e... -
Page 16: Function Table
(External device device such as a relay or contactor. If the monitoring) feedback signal from the external device is not correct, the F3SN enters lockout condi- tion. 7 Dark-ON output mode The ON/OFF-state is inverted from the (Auxiliary output) OSSD outputs state. This mode is the de- fault of the auxiliary output. -
Page 17: Revision History
F F F F 3 3 3 3 S S S S N N N N F F F F 3 3 3 3 S S S S N N N N Safety Light Curtain Safety Light Curtain Safety Light Curtain Safety Light Curtain s s s s e e e e... - Page 18 Just Fit, Reliable, Easy. © OMRON Corporation 2001 All Right Reserved. Specifications are subject to change without notice.
Need help?
Do you have a question about the F3SN and is the answer not in the manual?
Questions and answers