Installation - Ferro 25-40-130 Instruction Manual

ODSTRÁNENIE PROBLÉMOV
Porucha
čerpadlo sa netočí
Systém je hlučný
Čerpadlo je hlučné
Čerpadlo sa spustí, ale po krátkej
dobe sa zastaví
EN
Warnings
Installation, electrical connection and setting up of
the pump must be carried out by skilled personnel
in compliance with the general and local safety regu-
lations in force. Failure to abide by these instructions
invalidates every right to the guarantee, as well as
endangering persons and things.
This device can be used by children at age at least 8
years and by people with limited physical and mental
abilities, and by people with lack of experience and
knowledge, if instruction concerning safty use of the
device will be provided, so that the associated risks
will be understood. Children should not play with the
device. Children should not be allowed to clean and
maintain the equipment.
Range of use
This circulation pump is suitable for drinking water only.

Installation

On the delivery pipe or the return pipe. The arrow
stamped on the pump body indicates the direction
of flow - fig. 1. Install an interception valve on both the
intake pipe and the delivery pipe - fig. 2.
ALWAYS fit the circulation pump with the motor shaft
in a horizontal position, avoiding the dripping of water
onto the motor and onto the terminal board - fig. 3.
The water hardness TH should not be higher than 15 �F.
Electrical connection
Supply voltage and frequency must be the same as
shown on the data plate. The circulation pump must
always be connected to earth. Make the connection
10
Príčina
Nie je napájanie
Zlé napájanie
Zlý kondenzátor (jednofázový
motor)
Zablokovaný rotor
Príliš vysoký prietok
Zavzdušnený systém
Vzduch v čerpadle
Malý sací tlak
Nečistoty medzi rotorom a
statorom alebo medzi obežným
kolesom a telesom čerpadla.
as indicated below - fig. 4.
Fit a two-pole switch with contact opening distance
of at least 3 mm. Power supply should be connected
via an appropriate fuse. Use rubber cables H05RR-F
3xO,75 mm
Starting up
After installation, fill and bleed the system before
running the pump. Start the circulation pump at
top speed - fig. 6.
If it is necessary to bleed air from the motor, slowly
slacken the breather cap and let the water flow out
for a few seconds - fig. 7. Avoid running the circulation
pump when there is no water in the system. Take care,
danger of scalds - fig. 8.
Speed adjustment, on pumps provided with the
necessary device, is accomplished by turning the
knob of the three-position switch, even when the
motor is live - fig. 9.
Maintenance
The circulation pump does not require any main-
tenance.
At the start of the winter season, ensure that the
motor shaft is not blocked - fig. 10.
Warranty conditions
1. Ferro S.A. company provides a 24-month war-
ranty for a correct operation of the Ferro pump
in agreement with its application and technical
conditions specified in the Instruction Manu-
al, and 6-month warranty for repairs and used
spareparts. Warranty period starts on the final
user purchase date. Warranty applies on the
territory of Poland, for other countries seller is
responsible for any warranty certificates.
Riešenie
Skontrolujte napájanie a istič
Skontrolujte správne napätie
Vymeňte kondenzátor
Zvoľte maximálnu rýchlosť a /
alebo uvoľnite rotor pomocou
skrutkovača
Zvoľte menší výkon čerpadla
Odvzdušnite systém
Odvzdušnite čerpadlo
Zvýšte tlak v saní
Skontrolujte, či sa hriadeľ otáča
voľne. Odstráňte všetky nečistoty.
- fig. 5.
2