Configuring a 1:10 s-Video (Y/C) DA Technical Specifications Figures Figure 1: VM-1045 Video Component Distributor – Front and Rear View Figure 2: Underside of the VM-1045 Video Component Distributor Figure 3: Connecting a VM-1045 Video Component Distributor Figure 4: Configuring as a 2x1:5 s-Video (Y/C) DA...
GROUP 6: Accessories and Rack Adapters; GROUP 7: Scan Converters and Scalers; and GROUP 8: Cables and Connectors 2 Download up-to-date Kramer user manuals from our Web site at http://www.kramerelectronics.com 3 The complete list of Kramer cables is on our Web site at http://www.kramerelectronics.com Introduction...
Page 4
Getting Started KRAMER: SIMPLE CREATIVE TECHNOLOGY...
The unit has four channels. Each channel includes seven BNC connectors: an input, a looping output, and five outputs. The VM-1045 can be configured as a 1x1:5 component RGB/S DA, a 2x1:5 s-Video (Y/C) DA or as a 4x1:5 composite video DA.
Your VM-1045 Video Component Distributor Figure 1: VM-1045 Video Component Distributor – Front and Rear View Figure 2: Underside of the VM-1045 Video Component Distributor KRAMER: SIMPLE CREATIVE TECHNOLOGY...
TERM 75 / Hi-Z Button LOOP BNC Connector OUT BNC Connector Power Connector with Fuse Table 2: Underside Features of the VM-1045 Video Component Distributor Feature LEVEL Trimmer EQ. Trimmer 1 Independent controls per channel (from A to D) 2 For looping select Hi-Z...
Always mount the machine in the rack before you attach any cables or connect the machine to the power If you are using a Kramer rack adapter kit (for a machine that is not 19"), see the Rack Adapters user manual for...
1 Switch OFF the power on each device before connecting it to your VM-1045. After connecting your VM-1045, switch on its power and then switch on the power on each device. Switching on the VM-1045, recalls the previous setup from the non-...
1:20 composite video DA (see section 7.3) or a 2x1:10 composite video DA 1:10 s-Video DA (see section 7.4) 7.1 Configuring a 2x1:5 s-Video (Y/C) DA You can configure the VM-1045 as a 2x1:5 s-Video (Y/C) DA (see Figure 4): s-Video Source...
Configuring the VM-1045 Video Component Distributor 7.3 Configuring a 1:20 composite video DA Figure 6 illustrates the VM-1045 as a 1:20 composite video DA: Composite Video Source Composite Video Display 1 Figure 6: Configuring as a 1:20 Composite Video DA 7.4 Configuring a 1:10 s-Video (Y/C) DA...
WEIGHT: ACCESSORIES: 1 Specifications are subject to change without notice Technical Specifications of the VM-1045 Video Component Distributor 4 x 1 video inputs, 1Vpp/75 on BNC connectors with loop 4 x 5 video outputs, 1Vpp/75 on BNC connectors 2.7Vpp 415MHz 0.03%...
Page 14
EXCLUSION OF DAMAGES The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option. Kramer shall not be liable for: 1. Damage to other property caused by defects in this product, damages based upon inconvenience, loss of use of the product, loss of time, commercial loss;...
Page 15
For the latest information on our products and a list of Kramer distributors, visit our Web site: www.kramerelectronics.com, where updates to this user manual may be found. We welcome your questions, comments and feedback. Safety Warning: Disconnect the unit from the power supply before opening/servicing.
Need help?
Do you have a question about the VM-1045 and is the answer not in the manual?
Questions and answers