Related Manuals for Audi 8T8.071.126.A
Summary of Contents for Audi 8T8.071.126.A
- Page 1 Service Fitting instruction Audi A5 Sportback (8T) 2010 Body Roof bars, for scope of delivery 8T8.071.126.A Edition 8.09 Service Department. Technical Information...
-
Page 2: Table Of Contents
Setting the roof bar width ............... . . All rights reserved. No reproduction without prior agreement from publisher. Printed in Germany Copyright © 2009 Audi AG, Ingolstadt... -
Page 3: General Notes
A Caution symbol indicates that failure to follow ♦ information can lead to vehicle damage. Note Text with this symbol contains additional useful information. Audi AG shall not accept responsibility in the event of failure to comply with these assembly instructions. 1 General notes... -
Page 4: Safety Notes
Audi A5 Sportback (8T) 2010 No. 122, Body, Edition 8.09 Safety notes Permissible roof load max. WARNING! 75 kg 165 lbs Do not exceed the permissible roof load of 75kg (165lbs.). Do not exceed the gross vehicle weight rating of roof bars, add-on components and load of 75 kg (165 lbs.). - Page 5 Audi A5 Sportback (8T) 2010 No. 122, Body, Edition 8.09 Load — Do not tension roof bars against each other WARNING! Do not tension roof bars against each other. ZUB-0220 Load — install the roof bars first, then install the add-on...
- Page 6 Repairs or the replacement of parts must only be performed by a qualified workshop. It is recommended that genuine spare parts available from your Audi partner are used. Caution! The height of the vehicle will change due to the installation of the roof bars with/without add-on components.
-
Page 7: Parts
Audi A5 Sportback (8T) 2010 No. 122, Body, Edition 8.09 Parts Scope of delivery – Before installing the roof bars, check parts for completeness. Units Description Information Front roof bars Label on the underside in direction of travel left Rear roof bars... - Page 8 Audi A5 Sportback (8T) 2010 No. 122, Body, Edition 8.09 12 - Claw fastener front left front right rear left rear right 13 - Tensioning bolt (4x) 14 - Assembly tool 15 - 4-Nm torque wrench 16 - Cover flap (4x)
-
Page 9: Installing/Removing Roof Bars On Vehicle
Audi A5 Sportback (8T) 2010 No. 122, Body, Edition 8.09 Installing/removing roof bars on vehicle Installing roof bars on vehicle Preparing roof bars for installation: – Open the lock -17- using the key -18-. – Note the key number of your roof bars. This will facilitate replacement in the event of loss. - Page 10 Audi A5 Sportback (8T) 2010 No. 122, Body, Edition 8.09 Determining the installation position: The positioning bolts -X- are located beneath the rubber lips between the decorative trim and the roof frame. Note The illustration shows the car from the left-hand side.
- Page 11 Audi A5 Sportback (8T) 2010 No. 122, Body, Edition 8.09 – Unhook the claw fastener -12- from the installation posi- tion on the support bracket- 9- by pulling upward, then swivel down. ZUB-0344 – Insert the claw fastener -12- in the positioning bolts -X- above the assembly tool and slide it carefully in as far as it will go.
- Page 12 Audi A5 Sportback (8T) 2010 No. 122, Body, Edition 8.09 2. Slide the roof bar half way back on the claw fastener -12-. Once this procedure is complete, the positioning bolt -X- must be aligned so that it sits centrally between the starting position and the stop.
-
Page 13: Installing Add-On Components
Audi A5 Sportback (8T) 2010 No. 122, Body, Edition 8.09 Installing add-on components – Secure the add-on components in accordance with the relevant assembly instructions. – To install the add-on components, remove the profile cap -1- from the profile tube -5- -arrow A-. -
Page 14: General Notes
Audi A5 Sportback (8T) 2010 No. 122, Body, Edition 8.09 – Turn bolt -13- approx. 10 times to screw in. – Close the cover flap -16- and lock the lock with the key. General notes Technical data Weight of roof bar set: approx. 6 kg... - Page 15 Audi A5 Sportback (8T) 2010 No. 122, Body, Edition 8.09 – Adjust the roof bar so that the rubber support on the right-hand support bracket housing sits flush with the roof edge -arrow-. ZUB-0345 The gap -a- must not exceed 1 mm.