Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Administrator's Manual
Advertisement
Table of Contents
Related Manuals for QMS 3225
Summary of Contents for QMS 3225
- Page 1 QMS 3825/3225 Print System Large-Large- Capacity Input Tray Option 1800403-001C This document was created with FrameMaker 4.0.4...
-
Page 2: Proprietary Statement
QMS, Inc., and PS Executive Series is a trademark of QMS, Inc. Proprietary Statement The digitally encoded software included with your QMS 3825/3225 Print System is Copyrighted 1995 by QMS, Inc. All Rights Reserved. This software may not be reproduced, modified, displayed, transferred, or copied in any form or in any manner or... -
Page 3: Table Of Contents
Contents Introduction ... 1 Installing the LLCIT 1 Moving the Printer 1 Large-Large-Capacity Input Tray Indicators 2 Selecting a Paper Size 2 Adding Paper to the LLCIT ... 3 Changing LLCIT Paper Size ... 4 Remove and Disassemble the LLCIT 4... -
Page 5: Introduction
Introduction The Large-Large-Capacity Input Tray (LLCIT) for your QMS 3825/ 3225 Print System allows you to load 2,500 sheets of paper at a time, in letter, legal, ledger, A3, A4, and B4 sizes. Installing the LLCIT The LLCIT must be installed by a QMS-authorized service represen- tative. -
Page 6: Large-Large-Capacity Input Tray Indicators
Service instructions for changing the paper size begin on page 4. If you damage the printer or the Large-Large-Capacity Input Tray while changing the size settings, it will affect your warranty. QMS 3825/3225 Large-Large-Capacity Input Tray Option Once you know how to load paper from reading this manual, the step-by-step illustrations will help you remember in what order to perform the various steps. -
Page 7: Adding Paper To The Llcit
» Note: Only a qualified QMS service technician should change the LLCIT paper size. Service instructions begin on page 4. If you damage the printer or the Large-Large-Capacity Input Tray while changing the size settings, it will affect your warranty. -
Page 8: Remove And Disassemble The Llcit
Remove the upper and lower input bins. Press the Tray Down button. As soon as the tray moves down enough to remove the paper, open the door to stop the tray movement. Remove all the paper. QMS 3825/3225 Large-Large-Capacity Input Tray Option... - Page 9 Set it gently on the floor, being careful not to over- extend the cable at the back-right corner of the tray. QMS 3825/3225 Large-Large-Capacity Input Tray Option Changing LLCIT Paper Size...
- Page 10 Changing LLCIT Paper Size 11 Unscrew the silver screw from the top back of the indicator area cover. 12 Open the front door of the LLCIT. QMS 3825/3225 Large-Large-Capacity Input Tray Option...
- Page 11 15 Carefully lift the indicator area cover forward to clear the magnetic door clasp and set it gently on the floor, being careful not to overextend the blue wire harness. QMS 3825/3225 Large-Large-Capacity Input Tray Option Changing LLCIT Paper Size...
- Page 12 Changing LLCIT Paper Size 16 Remove the clear lid. QMS 3825/3225 Large-Large-Capacity Input Tray Option...
-
Page 13: Set Dip Switches To Match Paper Size
11 x 8.5" 8.5 x 11" Legal Ledger Sizes shown in shaded cells are not available on this printer. QMS 3825/3225 Large-Large-Capacity Input Tray Option This document was created with FrameMaker 4.0.4 Changing the LLCIT Paper Size Down = 0... -
Page 14: Adjust Side Rails To Match Dip Switches
After adjusting both sides, skip to “Reassemble the LLCIT,” on page 16. » Note: If you are changing between Letter and Ledger or between A3 and A4, the side rails do not need to be adjusted. QMS 3825/3225 Large-Large-Capacity Input Tray Option... - Page 15 Adjusting the Right Side Rail Remove the front and rear thumb screws on the right rail. Front Rear QMS 3825/3225 Large-Large-Capacity Input Tray Option Changing the LLCIT Paper Size...
- Page 16 Slide the rail until the front notch lines up with the proper size and the screw hole lines up with the matching hole. » Note: On the front rail, the forward screw hole matches international paper sizes while the rear hole matches US paper sizes. QMS 3825/3225 Large-Large-Capacity Input Tray Option...
- Page 17 » Note: On the back rail, the long slot matches international paper sizes while the short slot matches US paper sizes. Reinsert the thumb screws. QMS 3825/3225 Large-Large-Capacity Input Tray Option Changing the LLCIT Paper Size...
- Page 18 To change from any US size or B4 to A3 or A4, you must remove the left side rail from the tray. Follow these steps: Remove the front and rear thumb screws. QMS 3825/3225 Large-Large-Capacity Input Tray Option This document was created with FrameMaker 4.0.4 Letter...
- Page 19 3 black screws in the printer’s storage cabinet in case you change the paper size again later. Reattach the chain guide. Skip to “Reassemble the LLCIT” on page 17. QMS 3825/3225 Large-Large-Capacity Input Tray Option Changing the LLCIT Paper Size...
- Page 20 Align the side rail for the proper paper size and insert the two thumb screws. Lower the size indicator bar into place. Reattach the chain guide. Proceed to “Reassemble the LLCIT” on the next page. QMS 3825/3225 Large-Large-Capacity Input Tray Option 0039 tb...
-
Page 21: Reassemble The Llcit
Reassemble the LLCIT Angle the clear lid into place, inserting the right peg into its hole, then sliding the left peg into its groove. Leave the lid open. QMS 3825/3225 Large-Large-Capacity Input Tray Option Changing the LLCIT Paper Size... - Page 22 ACHTUNG! Man benötigt 2 Personen um den LLCIT zu tragen. Tragen Sie den LLCIT nie mit eingelegtem Papier. Reinstall the prop plate you removed at the outset of this process. QMS 3825/3225 Large-Large-Capacity Input Tray Option It takes two people to lift the LLCIT back into place.
- Page 23 Check the chart in your user’s guide or system administrator’s guide to find the proper feed edge. Reinsert the upper paper cassettes. Turn the printer on and wait for the tray to rise. QMS 3825/3225 Large-Large-Capacity Input Tray Option Changing the LLCIT Paper Size...