Canon XA70 Instruction Manual page 126

Menu Options
Menu item
[MIC ALC Link]
[Headphone Volume]
[Speaker Volume]
126
[Monitor Channels]
[HDMI Channels]
[Notification Sounds]
[Assign CH2 Switch & Dial]
[£ Display Setup] menu
Menu item
z
[Output Terminal]
[HDMI Max Resolution]
z
[SDI Output]
z
[3G-SDI Mapping]
z
[SDI/HDMI Scan Mode]
{
[HDMI Scan Mode]
[Output Status]
[LCD Brightness]
[LCD Backlight]
[VF Luminance]
[LCD/VF View Assistance]
[LCD Mirror Image]
Setting options and additional information
[ Linked], [ Separated]
Volume adjustment bar: 0 to 15 (8), [Ô] (softer), [Õ] (louder)
Volume adjustment bar: 0 to 15 (8), [Ø] (softer), [Ù] (louder)
In mode only, this setting is an alternative way to adjust the built-in speaker's volume
(A 105).
[ƒ CH1/CH2], [š CH1/CH1], [Ÿ CH2/CH2], [
[ CH3/CH4], [ CH3/CH3], [
[ CH1/CH3], [ CH2/CH4], [
[ƒ CH1/CH2], [ CH3/CH4]
[ High Volume], [ Low Volume], [j Off]
A beep will accompany some of the camcorder's operations.
• While pre-recording is activated, the camcorder will not emit any notification sounds.
[ CH2], [ CH3]
You can adjust the audio levels for CH2 or CH3 using the CH2 audio level switch and dial.
Setting options and additional information
[ø SDI], [ù HDMI]
[3840x2160]*, [1920x1080], [1280x720(59.94P)]
* Available only in mode.
[1920x1080], [1280x720(59.94P)]
[ Level A], [ Level B]
[ P], [ PsF (Forced 1080i)]
—
Displays a screen where you can check the configuration (video and audio) of the output signal.
Brightness adjustment bar, [ ] (darker), [
• Changing the brightness of the screen does not affect the brightness of your recordings or the
brightness of the playback image on a TV.
[ Max Brightness], [ Bright], [
[ High], [ Normal]
Changes the LCD screen's backlight level to one of four levels or the viewfinder's luminance level to
one of two levels, affecting the general brightness of the screen.
• Changing the brightness of the screen does not affect the brightness of your recordings or the
brightness of the playback image on a TV.
[i On], [j Off]
When this setting is set to [i On] and the gamma curve component of the [Gamma/Color Space]
setting in the custom picture file (A 94) is set to [Canon Log 3], the image displayed on the screen
will approximate the one that would be obtained using [BT.709 Wide DR] gamma settings.
[i On], [j Off]
When this setting is set to [i On], this function reverses the image on the screen horizontally
when you rotate the LCD panel 180 degrees toward the subject. In other words, the screen will show
a mirror image of the subject.
• If the camcorder is operated (touch screen, physical buttons and switches, or remote operation)
while the mirror image is displayed, the normal image will be displayed temporarily. After about
4 seconds, the mirror image is displayed again.
CH1+2/CH1+2],
CH4/CH4], [ CH3+4/CH3+4],
CH1+3/CH2+4]
] (brighter)
Normal], [ Dim]
(A 78)
(A 82)
(A 116)
(A 117)
(A 113, 114)
(A 114)
(A 113)
(A 113)
(A 115)