2.1 Overview Devices The manual refers to the following devices (Order code printed in bold type): • SCN-BWM55.02 Motion Detector/Automatic Switch 55, White matt finish o Flush mounted, Integrated bus coupling unit • SCN-BWM55.G2 Motion Detector/Automatic Switch 55, White glossy finish o Flush mounted, Integrated bus coupling unit •...
2.2 Connection diagram Figure 1: Connection diagram 2.3 Structure & Handling The following picture shows the structure of the MDT Motion Detector/Automatic Switch (with the example of SCN-BWMxxT.x2): Figure 2: Overview – Hardware module 1 = KNX bus connection terminal...
The red LED can optionally be used as a pure programming LED or switched via a separate object. Scenes Up to 8 scenes can be activated which can cause adjustable actions in the light channels 1/2. MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
MDT SCN-USBR.02 or SCN-IP000.03 / SCN-IP100.03. Updateable via DCA (from Hardware Version R2.0) If necessary, the actuators can be updated with the help of the MDT Update Tool. 2.5 Commissioning After wiring, the allocation of the physical address and the parameterization of every channel follows: (1) Connect the interface with the bus, e.g., MDT USB interface.
Page 9
133 Button left Status for change of direction 1 Bit 133 Button left long Switch 1 Bit 133 Button left long Toggle 1 Bit MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Page 10
"C" stands for communication, "R" for reading, "W" for writing, "T" for transmitting and "U" for updating. MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Series .02 4 Reference ETS-Parameter 4.1 General settings The following picture shows the submenu for the general settings: Figure 3: General Settings MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Page 12
Switch-off when exceeding… 75 – 1000 Lux Setting the brightness threshold [800] from when the sensor sends an OFF telegram. MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Page 13
"after fixed Manual mode, fallback 1 s – 9 h time". time at OFF (Night) 10 min Table 4: General Settings MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Page 14
Day = 1 / Night = 0, Day = 0 / Night = 1 Operating – Output 1 Bit Sending a cyclic "In operation" telegram Table 5: General communication objects MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Follow-up time “Night” 1 s – 4 h Setting the follow-up time for Night [30 s] mode. Table 7: Basic settings – HVAC channel MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Page 19
3 minutes, the light would be switched on for at least 3 minutes if movement was detected. Each new detection leads to a retriggering and thus a restart of the follow-up time. MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
• Force control AUTO (control = 0, value = 0) After that the normal operation of the detector is continued MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Page 21
1 Bit Switching on the light channel and locking the light channel in the ON state Table 9: Communication objects – Forced guidance/lock MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
This object is only available for the light channels! Object type for output The parameter defines the data point type of the output object. These are explained below: MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Setting a new dimming value when switching ON Teach-in dimming value for ON Table 12: Communication objects – Output object: Dimming absolute MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
"ON" cyclically. The time interval can be set between 10 s and 60 min. In addition, the second switching object (only light channel) can send its value cyclically. MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
The parameter "Idle time after external button short OFF" is useful, for example, to leave the room briefly after switching OFF via the external push-button without avoiding a renewed switching ON of the light by detection. MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Sends the set status HVAC - Status – Lock/Manual mode 1 Bit Sends the set status Table 18: Communication objects – Status information MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Page 31
The light is then switched OFF and the light channel changes to the state "Auto mode, ready". MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Page 32
The output is then switched to the orientation light state and can therefore dim the light to a darker level to leave the room safely. MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Page 33
The light channel can also be overridden via the "external push-button - short" object. The motion detector can be switched to manual mode by pressing twice MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Page 34
The output is then switched to the orientation light state and can therefore dim the light to a darker level to leave the room safely. MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
In this case, the follow-up time of the master and slave are added up. MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Status for toggle the status of the actuator to be switched (for subfunction "toggle"). Table 34: Communication objects – Single-button function: Switch short/long MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
1 Bit about the status of the actuator to be controlled Status for toggle Table 35: Communication objects – Single-button function: Dimming MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
1 Bit about the direction of the shutter actuator Status for change of direction Table 37: Communication objects – Single-button function: Blinds/Shutter MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
1 Bit Sends the respective value when the button is pressed and released Table 39: Communication objects – Single-button function: Send state MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
• active • LED red, object Activation of an object to control not active • „LED red flashing“ the red LED active MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Page 50
Controlling the LED via an external object Table 43: Communication objects – LED Important: When the white LED (Night light) is active, the brightness value is not evaluated! MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
The following table shows the corresponding communication object: Number Name/Object Function Length Usage Scene – Input 1 Byte Call-up of a scene Table 45: Communication object – Scene MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
"Basic setting" of the switch-on threshold. If it is now bright due to daylight and the switch-on threshold is exceeded, all indirect LED lights should also no longer switch on. MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Page 53
Number Name/Object Function Length Usage Brightness – Measured value 2 Byte Sending the current measured brightness value Table 47: Communication object – Brightness MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Number Name/Object Function Length Usage Temperature – Measured value 2 Byte Sending the current temperature value Table 49: Communication object – Temperature MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
The “Additional text” is merely additional information to the logic. This is not visible anywhere else. MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Page 56
Setting the value to be sent “False/True” Value for output 0 … 255 Visible with “1Byte Decimal”. value “False/True” [0 %] Setting the value to be sent MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
Page 57
Output of the logic function. DPT depending on the output object parameter 2 Bit/ 1 Byte Table 51: Communication objects – Logic MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...
The units are approved for operation in the EU and bear the CE mark. Use in the USA and Canada is not permitted! 6.4 History V 1.0 First Version of Technical Manual DB V4.4 03/2022 MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: +49-2263-880 • Fax: +49-2263-4588 • knx@mdt.de • www.mdt.de...