Table of Contents
Advertisement
Quick Links
GBA Z 0675 2 E
Instructions for Use
Induction heat retaining unit
for built-in
Hold-Line „GN" with CNS-frame
BH/HO/IN 800 CNS
BH/HO/IN 1600 CNS
BH/HO/IN 2400 CNS
BH/HO/IN 3200 CNS
Scholl Apparatebau GmbH & Co. KG
Zinhainer Weg 4
D–56470 Bad Marienberg / Germany
Phone
+0049 (0) 2661 – 9868-10
Fax
+0049 (0) 2661 – 9868-38 (Service)
Internet
www.scholl-gastro.de
E-mail
info@scholl-gastro.de
BA
Last revised 11-2020
Art. No. Z 0675
Art. No. Z 0676
Art. No. Z 0677
Art. No. Z 0678
Page 1 of 29
November 9, 2020
Rev. 2
Advertisement
Table of Contents
Related Manuals for Scholl BH/HO/IN 800 CNS
Summary of Contents for Scholl BH/HO/IN 800 CNS
- Page 1 Art. No. Z 0676 BH/HO/IN 2400 CNS Art. No. Z 0677 BH/HO/IN 3200 CNS Art. No. Z 0678 Scholl Apparatebau GmbH & Co. KG Zinhainer Weg 4 D–56470 Bad Marienberg / Germany Phone +0049 (0) 2661 – 9868-10 +0049 (0) 2661 – 9868-38 (Service) Internet www.scholl-gastro.de...
-
Page 2: Table Of Contents
GBA Z 0675 2 E ABLE OF CONTENTS Table of contents ............................... 2 Preface ................................4 General remarks ............................5 Description of danger signs ......................5 Purpose of induction units ....................... 6 1.2.1 Generall information on GN Container ..................6 Description of products .......................... - Page 3 GBA Z 0675 2 E Safety conscious work ........................18 Safety information for the operator/operating personnel ............18 Unauthorized reconstruction and use of spare parts ..............19 Improper operating methods ......................19 Pan detection ..........................19 Power regulation..........................19 Out of operation ............................20 Fault finding/Rectification ........................
-
Page 4: Preface
REFACE Congratulations! In purchasing this new SCHOLL appliance you have chosen a product which meets highest technical stand- ards while providing outstanding convenience in practical use. This appliance has been designed with minimal energy consumption in mind. Used responsibly, it will serve you well in an ecologically sound manner. -
Page 5: General Remarks
GBA Z 0675 2 E ENERAL REMARKS These instructions for use contain information which is fundamentally important and must be taken into account during assembly, operation and maintenance. They must therefore be read very carefully before installation and operation by the responsible specialist staff and the operator(s). They must always be avail- able for consultation at the place of operation. -
Page 6: Purpose Of Induction Units
The induction heat retention units „RTCSmp Install Hold-Line“ are especially suitable as built-in units in closed counters. The heat retention process with this „RTCSmp Install Hold-Line“ unit is especially adjusted to the SCHOLL GN equipment. If other material is used, efficiency and function can be affected in a negative way. -
Page 7: Description Of Products
GBA Z 0675 2 E ESCRIPTION OF PRODUCTS COPE OF SUPPLY • Generator • 1 - 2 temperature operation units (with 1 heat retention plate 1 temperature operation unit / with 2 - 4 heat retention plates 2 temperature operation units) •... -
Page 8: Technical Specifications
GBA Z 0675 2 E ECHNICAL SPECIFICATIONS Case of Heat reten- CNS-frame Cut-out for Type Ceran surface generator tion plate CNS-frame 303x312x135 520x320x4 520x320x75 588x388x23 BH/HO/IN 557x357 mm Heat retention temperature Type Voltage Power fields operation units BH/HO/IN 800 230V 0,8kW BH/HO/IN 1600 230V... -
Page 9: Installation
GBA Z 0675 2 E NSTALLATION COPE OF DELIVERY The generator is delivered with one to four built-in heat retention plates including glass tops and one to two operating units (with 1 heat retention plate 1 temperature operation unit – with 2 – 4 heat retention plates 2 temperature operation units). -
Page 10: Installation Clipping
GBA Z 0675 2 E • Make sure that the induction unit does not take in hot ambient air (concerns units standing side by side, or one behind the other, or standing near a frying pan or an oven), otherwise an air duct incl. shackle has to be added. -
Page 11: Installation Clipping Model Bh/Ho/In 2400 Cns
GBA Z 0675 2 E 3.4.2 I BH/HO/IN 2400 CNS NSTALLATION CLIPPING MODEL Cut-out CNS-frame in top plate: 557x357 mm Advice for installation heat retention plate: As soon as the mounting devices according to the above mentioned steps are finished, you may continue with installation. -
Page 12: Generator Ho/In 3200-Gn
GBA Z 0675 2 E HO/IN 3200-GN ENERATOR Advice for installation generator: The rear case of the generator is equipped with two holes for the installation. Make sure that the height distance between fan and bottom and the laterial openings for air exit have a distance to obstacles of at least 40mm. -
Page 13: Mounting Variations
GBA Z 0675 2 E OUNTING VARIATIONS Page 13 of 29 November 9, 2020 Last revised 11-2020 Rev. 2... -
Page 14: Cut-Out Operation Unit With Potentiometer
GBA Z 0675 2 E PERATION UNIT WITH POTENTIOMETER Advice for installation operation unit: This unit is supplied completely with an operation unit. In order to fix this on a cover, take the clipping for the power switch into account. The operation control panel has to be fixed vertically on the installation panel. -
Page 15: Electrical Installation
GBA Z 0675 2 E LECTRICAL INSTALLATION If the voltage is wrong, the induction unit can be CAUTION damaged. The installation of the electricity must be fitted by approved installation contractors in accordance with specific national and local installation in conformity with all safety regulations. The warning signs and rating plates on the units must strictly be followed. -
Page 16: Operation Test
To avoid injuries (burning) do not touch this area. Use exclusively the SCHOLL GN equipment for the RTCSmp Install Hold-Line heat retention unit. • Put some water in the serving pan and place it in the center of the heating area. -
Page 17: Operation
The heat retention unit is immediately ready for operation. The shining display indicates that energy is transferred to the bottom of the Chafing Dish or to the bottom of the SCHOLL GN equipment. The tempera- ture rating is set by turning the control knob. -
Page 18: Safety Instructions
SCHOLL GN equipment. To avoid injuries (burning) do not touch the heating area. • Switch the control knob off if you take the SCHOLL GN equipment away for a while. This will avoid the heat retention process to continue automatically when a serving pan is placed back on the heat- ing area. -
Page 19: Unauthorized Reconstruction And Use Of Spare Parts
The operating reliability of the induction unit can only be guaranteed by careful use. The limit values may not be exceeded on any account. AN DETECTION No power is transferred if no SCHOLL GN equipment is detected. OWER REGULATION The desired temperature is set by turning the rotary switch on the operation unit. Any temperature be- tween 50 and 100°C can be chosen. -
Page 20: Out Of Operation
GBA Z 0675 2 E UT OF OPERATION If the induction unit is out of operation make sure that the control knob is in the OFF-position. If you do not use the unit for a long period (several days), unplug the unit. Make sure that no liquid can enter into the unit, do not clean the induction unit with a jet of water. -
Page 21: Fault Finding/Rectification
GBA Z 0675 2 E AULT FINDING ECTIFICATION The induction appliance must only be opened by authorized and trained service personnel. Do not open the unit, dangerous electric voltage CAUTION inside. Stop any actions if the heating area (ceran plate) is cracked or broken, the induction unit must be switched off and disconnected from the electric supply. -
Page 22: Fault Finding With Error Code
GBA Z 0675 2 E AULT FINDING WITH ERROR CODE Error-No. Description Troubleshoot Hardware overcurrent or Check the bac material, coil is not connected Check wiring Software overcurrent Check the bac material Heat sink overtemperature Check installation (Airflow) T > 85°C Empty cooking detector, Check sensor unit. -
Page 23: Fault Finding Without Error Code
7- segment display is flashing (bottom diameter less than 20cm) equipment (If an error code appears see SCHOLL GN equipment is not in the Move the SCHOLL GN “Fault finding with error code”) center of the heating area (the in-... - Page 24 GBA Z 0675 2 E Fault Possible cause Action to take Heating cycle switches off and Overheated coil, Switch unit off, on within minutes, heating aera overheated remove Chafing Dish or cast iron (after a long operation time) pan and fill water into the pan, Empty cooking, no water in the pan let unit cool down The cooling-system (fan) starts to operate when the ambient temperature in the control area exceeds...
-
Page 25: Cleaning
GBA Z 0675 2 E LEANING List with common types of soiling and recommendations how to treat them: Type of soiling Treatment Slight soiling, no burned residues Wipe with a moist cloth (scotch), without cleaning agent Fatty spots Polychrom (sauces, soups, ...) ... -
Page 26: Support
GBA Z 0675 2 E UPPORT A good maintenance of the induction unit requires a regular cleaning, care and servicing. The operator has to ensure, that all components relevant for safety are in perfect working order at all times. The induction unit should be examined at least once a year by an authorized technician. Do not open the induction unit. -
Page 27: Waste Disposal Concept
GBA Z 0675 2 E ASTE DISPOSAL CONCEPT The symbol on the product or on its packaging indicates that this product may not be treated as household waste. It shall be handed over instead to the applicable collection point for the recycling of elec- trical and electronic equipment. -
Page 28: Warranty And Service
GBA Z 0675 2 E ARRANTY AND SERVICE 12.1 W ARRANTY CONDITIONS The manufacturer accepts no liability or warranty in the following cases: failure to observe notes and instructions given in the Instructions for Use; use of the product in a manner not conforming to its intended use; ... -
Page 29: Service Address
7:00 a.m. till 4:00 p.m. Fridays from 7:00 a.m. till 12:15 p.m. Outside these office hours please communicate your requests per e-mail or telefax. Scholl Apparatebau GmbH & Co. KG Zinhainer Weg 4 D-56470 Bad Marienberg / Germany Phone...