Page 1
GBA A 0811 0 E Instructions for Use Mobile plate dispenser Art. No. A 0811, A 0812, A 0813 Art. No. A 0814, A 0815, A 0816 Art. No. A 0817, A 0818, A 0819 Scholl Apparatebau GmbH & Co. KG Zinhainer Weg 4 D–56470 Bad Marienberg / Germany...
REFACE Congratulations! In purchasing this new SCHOLL appliance you have chosen a product which meets highest technical stand- ards while providing outstanding convenience in practical use. This appliance has been designed with minimal energy consumption in mind. Used responsibly, it will serve you well in an ecologically sound manner.
GBA A 0811 0 E ONVENTIONS – G ICTOGRAMS ENERAL SAFETY NOTES Be sure to observe these Instructions for Use as well as the safety notes to prevent injuries or damage to health or property. Do not alter or modify this appliance.
Page 5
GBA A 0811 0 E Do not run the power cord near heat sources, over sharp edges, etc. Always pull on the plug, not the cord, to remove it from a socket-outlet since the cord might be dam- aged as a result. Do not allow cords to hang unsupported. Route the cord so that it will...
GBA A 0811 0 E – W ICTOGRAMS ARNING NOTES Cleaning must only be performed by qualified persons who have read and under- stood these Instructions for Use and are familiar with applicable hygiene rules. En- sure that care is exercised during cleaning of the unit.
GBA A 0811 0 E Allow the unit to cool down before starting any cleaning work. Burn hazard – I ICTOGRAMS MPORTANT NOTES DANGER indicates an immediately threatening hazard. Failure to observe this warning notice will result in severe physical injury or death.
Page 8
GBA A 0811 0 E IMPORTANT Improper use may result in minor injuries or damage to property. In addition to these Instructions for Use, a number of accident prevention and other regulations apply with regard to the operation of this appliance. As re- gards food handling, please observe HACCP rules concerning compliance with hygiene requirements.
GBA A 0811 0 E NTRODUCTION This operating manual gives information about the function, operation and use of your stacking and output devices, hereinafter called "stacker". The operating manual applies to everyone, who receives and checks the device, ...
GBA A 0811 0 E ESCRIPTION Depending on model and version, the stacker has been made up of the following element: 1) Casing: a) closed, half-open (model ORT-MS) or completely open (model OX-MS), b) with or without heating tray and switch panel, c) with or without push-in grip.
GBA A 0811 0 E UNCTION If the tension force of the coil spring has been adjusted well to the weight of the tableware, the upper ta- bleware part should be flush with the upper edges of the guides. When the upper tableware part is removed, the tableware part below it will take its place. The totality of the springs determines the tension force of the stacker.
GBA A 0811 0 E CCEPTANCE CHECKING Between production and despatch, every stacker is checked for: damage completeness of deliverables functioning of the stacking mechanism functioning of switches, thermostat and heating element as well as for electrical safety.
GBA A 0811 0 E NSTALLING 1) Remove the packaging. 2) Remove the plastic foil from the casing and the platform. 3) Adjust the spring force by using an item of tableware on the stacker: a) Take the platform off the support or the removable panel from the side of the push-in grip (only model OX-MS) and the springs can now be reached.
GBA A 0811 0 E PERATION Engage the castors during loading and unloading and when pre-warming tableware. Disengage the castors when moving the stacker. TAKE CARE AT TRESHOLDS: NEVER BUMP FORCEFULLY INTO THRESHOLDS, REGARDLESS OF WHETHER THE STACKER IS LADEN OR EMPTY.
GBA A 0811 0 E LEANING Remove every day dust / dirt from the lid and the cover of the stacker, using a moist cloth. Remove dust / dirt from inside the stacker at least twice a year: set the switch to "0",...
GBA A 0811 0 E ERVICE AND AINTENANCE 1) Check the suitable spring force twice a year. The tension force can weaken as a result of excessive pulling out and the influence of heat. Now suspend unused springs or replace all springs by new ones: set the switch to "0",...
Page 17
GBA A 0811 0 E 4) Replace defective or damaged parts as follows: inform your supplier or customer service centre, make a note of the position and connections of the defective part and mount the new parts in exactly the same way, put the heating tray and switch panel in the old position and carefully tighten all screws.
GBA A 0811 0 E ECHNICAL DATA Art. No. Execution ExternalDimensions Dimensions Pile height Voltage Power B x T x H in mm crockery in mm in mm 1 pile A 0811 485 x 520 x 978 190-238 230V 0,6kW...
GBA A 0811 0 E ISPOSAL AND ENVIRONMENT The appliance has been packed before shipping to protect it against damage in transit. After unpacking, please dispose of packing materials in an environmentally sound manner. All packing materials are eco-compatible, 100% recyclable and marked with a symbol to that effect.
GBA A 0811 0 E ARRANTY AND SERVICE ARRANTY CONDITIONS The manufacturer accepts no liability or warranty in the following cases: failure to observe notes and instructions given in the Instructions for Use; use of the product in a manner not conforming to its intended use;...
GBA A 0811 0 E IMPORTANT To enable our customer service to prepare repairs carefully and to provide the appro- priate spare parts, please provide the following information when reporting a custom- er service requirement: Your precise address (where applicable, final customer's address, person to contact) 2.