Advertisement
MATERIALS:
FDA approved blow molded high-density polyethylene with Microban
steel finish. Reinforced full-length steel-on-steel hinge mechanism, with 11-gauge steel mounting plates and mounting
hardware included. Molded in graphics & Safety Messages in six languages. Contoured changing surface area is 420 sq.
in. (2730 sq. mm) and comes complete with nylon safety straps and bag hooks.
OPERATION:
Concealed pneumatic cylinder and hinge structure provides controlled, slow opening and closing of bed. Stainless steel
is easy to clean and resists odors and bacterial growth. Complies with ASTM static load performance requirements when
properly installed. Built-in liner dispenser holds approximately 25 KB150-99-INB sanitary liners.
Warning: To insure that the unit supports the intended loads, baby changing stations must be properly installed
according to the manufacturer's instructions.
INSTALLATION:
To insure proper installation and compliance to building codes, it is recommended that a qualified person or carpenter
perform the installation of the unit. The unit must be properly installed onto a permanent wall that is capable of supporting
significant weight and can accommodate the supplied installation hardware. The Koala Baby Changing Station meets
ADA regulations when properly installed.
Drilling holes and mounting the station:
1. Remove the station from the shipping container and check
for any freight damage. Identify the best location for
installing the baby changing station. Hold the unit in place,
open the bed, and make sure that there is adequate
operating clearance.
2. Select the wall area where the Baby Changing Station will
be installed. Measure from the floor, at the center of the
stud, and mark the wall at 62" (1575 mm). Hold the unit in
place to verify alignment. Cut a hole 22.5" (565mm) wide,
36" (902mm) high and 4" (102mm) deep in the wall and
construct mounting frame as shown in Fig1.0. If the wall
surface is masonry or tile over wood studs, use caution
when cutting the hole for the unit.
3. The unit comes with two mounting brackets that need to be
secured to the mounting frame as shown in Fig 1.0.
4. Place the unit into the recessed area and insert the capped
nuts and washers to hold the Baby Changing Station in
place. It may be necessary to adjust the squareness of the
door by using a shim on the top right or left side of the unit
before tightening securely to the wall.
SPECIFICATION:
Baby changing station body shall be durable, high-density polyethylene with Microban
brushed stainless steel finish. Design of unit shall be semi-recessed-mounted. Unit shall be equipped with a pneumatic
cylinder for controlled opening and closing of bed. Bed shall be secured to back plate with a concealed, full-length steel-
on-steel hinge. Unit shall have Microban
exposed on interior or exterior surfaces. Unit shall have 11-gauge steel mounting plates with mounting hardware
included. Unit shall conform to ANSI S117.1 Accessible and Useable Building and Facilities, ASTM F 2285-04 Standard
Safety Performance Specification for Diaper Changing Tables for Commercial Use, ANSI Z535.4 Product Safety Signs
and Labels, ASTM G21 Antifungal, ASTM G22 Antibacterial standards or local code if more stringent installation
requirements are applicable for Barrier-Free accessibility. Unit shall comply with ADA regulations when properly installed.
Bed shall have smooth concave changing area with a nylon safety strap and two hooks for bags or purses. Unit shall
have a built-in Liner Dispenser for use with 3-ply chemical free biodegradable sanitary liners, universal instruction
graphics and safety messages in 6 languages. Unit shall be backed by manufacturers 5-year limited warranty on
materials and workmanship, and a 5-year replacement warranty against vandalism. Unit shall be manufactured in the
U.S.A.
Baby Changing Station shall be model KB111-SSRE-INB of Koala Kare Products, A Division of Bobrick
6982 S. Quentin St. Centennial, CO 80112 USA
Tel: 1-888-733-3456 within the USA or +1 303-539-8300 outside the USA
Web: www.koalabear.com or www.bobrick.com
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet.The manufacturer
reserves the right to, and does from time to time, make changes and improvements in designs and dimensions without notice.
antimicrobial embedded into plastic material. No hinge structure shall be
®
antimicrobial clad in a type 304 brushed stainless
®
Fig 1.0
antimicrobial clad in a 304
®
KB111-SSRE-INB
© 2007 by Koala Kare Products, A Division of Bobrick
Revised 12-12-07
Printed In USA
Advertisement
