Advertisement
MATERIALS:
FDA approved rotation-molded high-density polyethylene with Microban
steel hinge mechanism and mounting hardware included. Molded in graphics and safety messages in five languages.
Contoured changing surface area is 307.72 sq. in. (198,529 sq. mm) and comes complete with nylon safety straps and
bag hooks.
OPERATION:
Concealed pneumatic cylinder and hinge structure provides controlled, slow opening and closing of bed. High-density
polyethylene is easy to clean and resists odors and bacterial growth. Complies with ASTM static load performance
requirements when properly installed.
Warning: To insure that the unit supports the intended loads, baby changing stations must be properly installed
according to the manufacturer's instructions.
INSTALLATION:
To insure proper installation and compliance to building codes, it is recommended that a qualified person or carpenter
perform the installation of the unit. The unit must be properly installed onto a permanent wall that is capable of supporting
significant weight, and can accomodate the supplied installation hardware. The Koala Baby Changing Station meets ADA
regulations when properly installed.
Drilling holes and mounting the station:
1. Remove the station from the shipping container and check for any freight damage. Identify the best location for
installing the Baby Changing Station. Hold the unit in place, open the bed, and make sure that there is adequate
operating clearance.
2. Based upon the type of wall on which the unit will be mounted, determine the best method of mounting. Not all of
included hardware may be required for proper installation.
3. The horizontal unit has four mounting holes provided in the back wall of the unit, which are positioned on a 16"
(406mm) stud center. If possible, locate the wood or metal wall studs for fastening the changing station in the
desired location. If the walls do not have studs on the center as outlined, make sure at least one side of the unit
is installed into the stud. Use toggles (supplied) for holes on the other side.
4. Find the stud where you will be attaching the left side of the changing station to the wall. Measure 46" (1168mm)
up from the floor, at the center of the stud, and mark the wall. Line up the top left mounting hole with this mark,
then use a measuring tape and level to mark the remaining three mounting holes. This will locate the bottom of
the station 29" (737mm) from the floor.
Using Wood Screws:
If the wall has wood studs on 16" (406mm) centers, drill 1/8" (3mm) pilot holes at the marks and use the four 1/4" (6mm)
x 3" (76mm) panhead tapping screws with supplied washers. If the wall is masonry or tile over wood studs, use a
7/32" (6mm) masonry drill until you hit the stud, then proceed to drill 1/8" (3mm) pilot holes into the studs and use the
four 1/4" (6mm) x 3" (76mm) panhead tapping screws with supplied washers.
Using Toggle Fasteners:
If the wall has wood studs that are not on 16" (406mm) centers, has metal studs, or an underlying surface of concrete
block, drill with a 1/2" (13mm) masonry bit. A minimum of 2-1/2" (64mm) of inside wall space is required for toggles to
turn. Insert supplied toggles and tighten, locate station over toggles, then use supplied 1/4" (6mm) x 3" (76mm) Phillips
Panhead machine screws with supplied washers.
SPECIFICATION:
Baby changing station body shall be durable, high-density polyethylene with Microban
be surface-mounted, oval. Unit shall be equipped with a pneumatic cylinder for controlled opening and closing of bed.
Bed shall be secured to back with a concealed, full-length steel-on-steel hinge. Unit shall have Microban
embedded into plastic material. No hinge structure shall be exposed on interior or exterior surfaces. Unit shall conform to
ANSI S117.1 Accessible and Useable Buildings and Facilities, ASTM F 2285-04 Standard Consumer Safety Performance
Specification for Diaper Changing Tables for Commercial Use, ANSI Z535.4 Product Safety Signs and Labels, ASTM
G21 Antifungal and ASTM G22 Antibacterial Standards or local code if more stringent installation requirements are
applicable for Barrier-free accessibility. Unit shall comply with ADA regulations when properly installed. Bed shall have
smooth concave changing area with a nylon safety strap and two hooks for bags or purses. Unit shall have a built-in
Liner Dispenser for use with 3-ply chemical free biodegradable sanitary liners, universal instruction graphics and safety
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet.The manufacturer
reserves the right to, and does from time to time, make changes and improvements in designs and dimensions without notice.
antimicrobial. Reinforced full-length steel-on-
®
antimicrobial. Design of unit shall
®
KB108-INB
© 2007 by Koala Kare Products, A Division of Bobrick
antimicrobial
®
Continued...
Revised 12-12-07
Printed In USA
Advertisement
