Advertisement
MATERIALS:
18-gauge, type 304 satin stainless steel exterior finish with FDA approved blow molded high-density grey polyethylene
with Microban
antimicrobial interior. Reinforced full-length steel-on-steel hinge mechanism, with 11-gauge steel
®
mounting plates and mounting hardware included. Molded in graphics and safety messages in six languages. Contoured
changing surface area is 442 sq. in. (2873 sq. mm) and comes complete with nylon safety straps and bag hooks.
OPERATION:
Concealed pneumatic cylinder and hinge structure provides controlled, slow opening and closing of bed. High-density
polyethylene is easy to clean and resists odors and bacterial growth. Complies with ASTM static load performance
requirements when properly installed. Built-in liner dispenser holds approximately 25 KB150-99-INB sanitary liners.
Warning: To insure that the unit supports the intended loads, baby changing stations must be properly installed
according to the manufacturer's instructions.
INSTALLATION:
To insure proper installation and compliance to building codes, it is recommended that a qualified person or carpenter
perform the installation of the unit. The unit must be properly installed onto a permanent wall that is capable of supporting
significant weight and can accommodate the supplied installation hardware. The Koala Baby Changing Station meets
ADA regulations when properly installed.
Drilling holes and mounting the station:
1. Remove the station from the shipping container and check for any freight
damage. Identify the best location for installing the Baby Changing Station.
Hold the unit in place, open the bed, and make sure that there is adequate
operating clearance.
2. Select the wall area where the Baby Changing Station will be installed.
Measure from the floor, at the center of the stud, and mark the wall for the
appropriate height. Hold the unit in place to verify alignment. Cut an opening
in the wall 35-1/2" (900mm) wide, 20-1/2" (529mm) high, 4" (102mm)
minimum depth and install framing on top, bottom and sides of wall opening.
If the wall surface is masonry or tile over wood studs, use caution when
cutting the hole for the unit.
3. The unit will be mounted using 4-1/4" (108mm) x 1-1/2" (38mm) wood
screws through the sides of the unit into the framing of the wall opening.
4. Place the unit into the recessed wall opening and insert the screws and flat
washers to hold the Baby Changing Station in place. It may be necessary to
adjust the squareness of the door by using a shim on the top right or left side
of the unit before tightening securely to the wall.
SPECIFICATION:
Baby changing station body shall have 18-gauge, type 304 satin stainless steel exterior finish with high-density grey
polyethylene interior. Design of unit shall be recessed-mounted. Unit shall be equipped with a pneumatic cylinder for
controlled opening and closing of bed. Bed shall be secured to back plate with a concealed, full-length steel-on-steel
hinge. Unit shall have Microban
interior or exterior surfaces. Unit shall have 11-gauge steel mounting plates with mounting hardware included. Unit shall
conform to ANSI S117.1 Accessible and Usable Buildings and Facilities, ASTM F 2285-04 Standard Consumer Safety
performance Specification for Diaper Changing Tables for Commercial Use, ANSI Z535.4 Product Safety Signs and
Labels, ASTM G21 Antifungal and ASTM G22 Antibacterial Standards or local code if more stringent installation
requirements are applicable for barrier-free accessibility. Unit shall comply with ADA regulations when properly installed.
Bed shall have smooth concave changing area with a nylon safety strap and two hooks for bags or purses. Unit shall
have a built-in Liner Dispenser for use with 3-ply chemical free biodegradable sanitary liners, universal instruction
graphics and safety messages in 6 languages. Unit shall be backed by manufacturer's 5-year limited warranty on
materials and workmanship, and a 5-year replacement warranty against vandalism. Unit shall be manufactured in
the U.S.A.
Baby Changing Station shall be model KB110-SSRE-INB of Koala Kare Products, A Division of Bobrick
6982 S. Quentin St. Centennial, CO 80112 USA
Tel: 1-888-733-3456 within the USA or +1 303-539-8300 outside the USA
Web: www.koalabear.com or www.bobrick.com
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet.The manufacturer
reserves the right to, and does from time to time, make changes and improvements in designs and dimensions without notice.
antimicrobial embedded into plastic material. No hinge structure shall be exposed on
®
KB110-SSRE-INB
Revised 12-12-07
© 2007 by Koala Kare Products, A Division of Bobrick
Printed In USA
Advertisement
