Advertisement
MATERIALS:
18-gauge, type 304 satin stainless steel exterior finish with FDA approved blow molded high-density grey polyethylene
with Microban
antimicrobial interior. Reinforced full-length steel-on-steel hinge mechanism, with 11-gauge steel
®
mounting plates and mounting hardware included. Molded in graphics and safety messages in six languages. Contoured
changing surface area is 442 sq. in. (2873 sq. mm) and comes complete with nylon safety straps and bag hooks.
OPERATION:
Concealed pneumatic cylinder and hinge structure provides controlled, slow opening and closing of bed. High-density
Polyethylene is easy to clean and resists odors and bacterial growth. Complies with ASTM static load performance
requirements when properly installed. Built-in liner dispenser holds approximately 25 KB150-99-INB sanitary liners.
Warning: To insure that the unit supports the intended loads, baby changing stations must be properly installed
according to the manufacturer's instructions.
INSTALLATION:
To insure proper installation and compliance to building codes, it is recommended that a qualified person or carpenter
perform the installation of the unit. The unit must be properly installed onto a permanent wall that is capable of supporting
significant weight and can accommodate the supplied installation hardware. The Koala Baby Changing Station meets
ADA regulations when properly installed.
Drilling holes and mounting the station:
1. Remove the station from the shipping container and check for any freight damage. Identify the best location for
installing the baby changing station. Hold the unit in place, open the bed, and make sure that there is adequate
operating clearance.
2. Based upon the type of wall on which the unit will be mounted, determine the best method of mounting. Not all of
included hardware may be required for proper installation.
3. The horizontal unit has four mounting holes provided in the back wall of the unit, which are positioned on a 32"
(813mm) stud center. If possible, locate the wood or metal wall studs for fastening the changing station in the
desired location. If the walls do not have studs on the center as outlined, make sure at least one side of the unit
is installed into the stud. Use toggles (supplied) for holes on the other side.
4. Find the stud where you will be attaching the left side of the changing station to the wall. Measure 45.5"
(1,156 mm) up from the floor, at the center of the stud, and mark the wall. Line up the top left mounting hole with
this mark, then use a measuring tape and level to mark the remaining three mounting holes. This will locate the
bottom of the station 28" (711 mm) and the top of the bed at 33" (838 mm) from the floor.
Using Wood Screws:
If the wall has wood studs on 16" (406mm) or 32" (813mm) centers, drill 1/8" (3mm) pilot holes at the marks and use the
four 1/4" (6mm) x 3" (76mm) panhead tapping screws with supplied washers. If the wall is masonry or tile over wood
studs, use a 7/32" (6mm) masonry drill until you hit the stud, then proceed to drill 1/8" (3mm) pilot holes into the studs
and use the four 1/4" (6mm) x 3" (76mm) panhead tapping screws with supplied washers.
Using Toggle Fasteners:
If the wall has wood studs that are not on 16" (406mm) or 32" (813mm) centers, has metal studs, or an underlying
surface of concrete block, drill with a 1/2" (13mm) masonry bit. A minimum of 2-1/2" (64mm) of inside wall space is
required for toggles to turn. Insert supplied toggles and tighten, locate station over toggles, then use supplied 1/4" (6mm)
x 3" (76mm) Phillips Panhead machine screws with supplied washers.
SPECIFICATION:
Baby changing station shall have 18-gauge satin stainless steel exterior finish with high-density polyethylene with
Microban
antimicrobial interior. Design of unit shall be surface-mounted. Unit shall be equipped with a pneumatic
®
cylinder for controlled opening and closing of bed. Bed shall be secured to back plate with a concealed, full-length steel-
on-steel hinge. Unit shall have Microban
exposed on interior or exterior surfaces. Unit shall have 11-gauge steel mounting plates with mounting hardware
included. Unit shall conform to ANSI S117.1 Accessible and Usable Buildings and Facilities, ASTM F 2285-04 Standard
Consumer Safety Performance Specification for Diaper Changing Tables for Commercial Use, ANSI Z535.4 Product
Safety Signs and Labels, ASTM G21 Antifungal and ASTM G22 Antibacterial Standards or local code if more stringent
installation requirements are applicable for barrier free accessibility. Unit shall comply with ADA regulations when
properly installed. Bed shall have smooth concave changing area with a nylon safety strap and two hooks for bags or
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet.The manufacturer
reserves the right to, and does from time to time, make changes and improvements in designs and dimensions without notice.
antimicrobial embedded into plastic material. No hinge structure shall be
®
Continued...
KB110-SSWM-INB Revised 12-12-07 Printed In USA
© 2007 by Koala Kare Products, A Division of Bobrick
Advertisement
