Battery Charge Indicator - Fein ASBS18-10AS Manual

1 609 92A 7HF • 28.6.22 • T
en
18
storage. This safety measure prevents the
dust extractor from being started accidentally.
Charging the Battery
Use only the chargers listed in the technical
u
data. Only these chargers are matched to the
lithium-ion battery of your dust extractor.
Note: Lithium-ion rechargeable batteries are
supplied partially charged according to interna-
tional transport regulations. To ensure full re-
chargeable battery capacity, fully charge the re-
chargeable battery before using your tool for the
first time.
Do not continue to press the on/off button
u
after the dust extractor has automatically
switched itself off. This can damage the bat-
tery.
A significantly reduced operating time after char-
ging indicates that the battery has deteriorated
and must be replaced.
Follow the instructions on correct disposal.

Battery Charge Indicator

When the rechargeable battery is inserted, you
can see the state of charge of the battery on the
battery charge indicator (4) on the dust ex-
tractor. When the rechargeable battery is re-
moved, you can see this on the battery itself.
Battery Charge Indicator on the Dust
Extractor
English
After the dust extractor is switched on, the five
green LEDs of the battery charge indicator (4)
will light up individually one after another in as-
cending and descending order. Then the LEDs
will indicate the state of charge of the
battery (19).
Battery Charge Indicator on the Rechargeable
Battery
English
If the rechargeable battery is removed from dust
extractor, its state of charge may be indicated by
the green LEDs of the battery charge indicator
on the battery.
Press the button for the battery charge indicator
or to show the state of charge.
If no LED lights up after pressing the button for
the battery charge indicator, then the battery is
defective and must be replaced.
Battery model GBA 18V...
LEDs
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
English
English
English
Capacity
60−100 %
30−60 %
5−30 %
0−5 %
Battery model ProCORE18V...
LEDs
5× continuous green light
4× continuous green light
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Inserting and Removing the Battery
(see figures A1−A2)
English
Do not use force to insert the battery. The
u
battery is designed in such a way that it can
only be inserted into the product when it is in
the right position.
Keep the battery compartment and the battery
u
bay clean and dry at all times to ensure good,
safe operation.
– Press the release button (10) to open the bat-
tery compartment cover (11).
– Slide the battery (19) into the battery bay (18)
until it audibly clicks into place.
– To remove the battery (19), press the release
button (20) on the battery and pull it out of the
battery bay (18).
– Close the battery compartment cover (11).
Fitting the Brackets for Extractor
Accessories (see figure B)
– Slide the bracket (21) for the suction tube and
crevice nozzle firmly into the adapter (9)
provided for it from above until it clicks into
place.
– Slide the bracket (23) for the vacuum hose and
floor nozzle firmly into the adapter (7)
provided for it from above and tighten the fix-
ing bolts (22).
Fitting the vacuum hose (see figure C)
– Insert the vacuum hose (12) into the hose ad-
apter (8) until both snap fasteners (24) of the
vacuum hose click into place.
Note: The friction generated by the dust in the
vacuum hose and accessory during extraction
causes an electrostatic charge that the user may
experience as static discharge (depending on en-
vironmental factors and their physiological state).
Fitting the Vacuuming Accessories
The vacuum hose (12) is equipped with a clip
system which can be used to connect vacuum-
ing accessories (dust extraction adapter (13),
curved nozzle (14)).
English
Capacity
80−100 %
60−80 %
40−60 %
20−40 %
5−20 %
0−5 %
English
English
English