The printer can be used as a wireless LAN printer by connecting the WLAN USB adaptor provided by BIXLON as an optional item. Besides the WLAN USB adaptor provided by BIXOLON, other WLAN USB adapters using the RT73 chipset can also be used.
Network Interface 2. How to Connect Both Ethernet and WLAN can be configured through the printer’s Ethernet interface. Likewise, both Ethernet and WLAN can also be configured though the printer’s WLAN interface. When you want to change the Ethernet or WLAN of the printer, the network settings of the host (PC, PDA, etc) and Ethernet or WLAN of the printer must configured properly configured so that communication can be established.
Page 6
Network Interface (2) Checking Network Setting 1) Function Key Pressing the Function Key while the power is ON will print the LAN/WLAN setting status page. *Output Message ETHERNET SETTING MAC ADDR: xx:xx:xx:xx:xx:xx LAN_DHCP disabled IP ADDR : 192.168.192.123 NETMASK : 255.255.255.0 GATEWAY : 192.168.192.254 PORT : 9100 WLAN SETTING...
Page 7
While the printer is turned off, turn on the printer while pressing the feed button. The printer setting values will then be printed with a beep sound. *Output Message SRP-F310 V01.00 STD 010110 ASCII ================================ ! " # $ % & ' ( ) * + , - . / 0 1 2 3 4 5 6 7 8 9 : ; < = > ? @ "...
Network Interface 2-1 Initial Wireless LAN Connection (Windows 2000) Windows 2000 does not support wireless network stting. When you use Windows 2000, you need to set the utility option as below after installing utility program related to the wireless lan driver that you use. - Network mode : Ad-hoc - SSID : BIXOLON_adhoc - IP address : 192.168.1.2...
Page 9
Network Interface 3) Select Internet Protocol (TCP/IP), and then click Properties. 4) Set the IP settings as shown below, and then click OK. Rev.1.02 - 9 -...
Page 10
Network Interface 5) Select the Wireless LAN tab, and then select “Use Windows to configure my wireless network settings.” Click the [Advanced] button. 6) Select “Computer-to-computer (ad hoc) network only.” Rev.1.02 - 10 -...
Page 11
Network Interface 7) Click the [Add] button. 8) Enter “BIXOLON_adhoc” as the Network name (SSID). Select the connection, even if the network is not broadcasted. Network Authentication: Select [Open] Data Encryption: Select [Disabled] Click the [OK] button. Rev.1.02 - 11 -...
Page 12
Network Interface 9) Click the “Connect” tab and check “Connect when this network is in range.” 10) Check whether the settings are updated as shown below, and then click [Close] When the printer is set to the default value (Adhoc mode, SSID: BIXOLON_adhoc), it will automatically connect.
Network Interface 2-3 Initial Wireless LAN Connection (Windows VISTA, Windows 7) When wireless utility program is installed, you have to set the wireless control values via the program, otherwise you have to terminate the program in order to do proper setting after following the steps 'Control Panel>>Administrative tools>>...
Page 14
Network Interface 3) Click the “Change adapter settings”. Click the “wireless network adaptor’s Properties”. 4) Select Internet Protocol Version 4(TCP/IPv4), and then click Properties. Rev.1.02 - 14 -...
Page 15
Network Interface 5) Set the IP settings as shown below, and then click OK. 6) Click the “Manage wireless networks”. Rev.1.02 - 15 -...
Page 16
Network Interface 7) Click the “Add”. 8) Click the “Create an ad hoc network”. Rev.1.02 - 16 -...
Page 17
Network Interface 9) Click the “Next”. 10) ‘Network name’ = BIXOLON_adhoc, ‘Security type’ = Open, ‘Save this network’ check, and then click the “Next”. Rev.1.02 - 17 -...
Page 18
Network Interface 11) Click the “Close”. 12) After completing configuration, Bixolon_adhoc network will be created. When the printer is set to the default value (Adhoc mode, SSID: BIXOLON_adhoc), it will automatically connect. Rev.1.02 - 18 -...
Network Interface 3. Configuration LAN Setting Values Classification Item Remarks Input Range Home LAN setting status display Printer Name Printer name 0~32 letters 0~32767 integers TCP Raw port that the Printer Port (except 21, 23, 25, 80, printer can use 443, 3318) System ID to use for ftp, telnet,...
Page 20
Network Interface WLAN Setting Values Classification Item Remarks Input Range Home WLAN setting status display Printer Name Printer Name 0~32 letters TCP Raw port that the printer 0~32767 integers Printer Port can use (except21,23,25,80,443,3318) ID to use for ftp, telnet, web- System User Name 1~32 letters...