BIXOLON Corporation. BIXOLON has no liability for loss or damage arising from or relating to your use of or reliance on the information in the document.
ESC J Print and feed paper GS / Print downloaded bit image ESC L Select page mode GS : Start/end macro definition ESC M Select character font GS B Turn white/black reverse print mode on/off - 4 - BIXOLON Rev. 1.00...
Page 5
GS v 0 Print raster bit image GS w Set bar code width BS M Select device font type Select cut mode and executes BS V a partial/full cut BS ^ P Set power saving mode - 5 - BIXOLON Rev. 1.00...
Argument value (Setting range) for the command Default : Initial argument value for the command Description : Detailed command function description Remarks : Additional information about using the command Differences : Variations depending on the printer model - 6 - BIXOLON Rev. 1.00...
The horizontal tab position is set by <ESC> D. ■ ■ With the underline mode turned on, the underline printing is not applied to the tab space created by this command. Differences : None - 7 - BIXOLON Rev. 1.00...
Page 8
This command prints the data in the print buffer and feeds one line based on the current set line spacing in standard mode. Remarks : In page mode, the printer does not perform actual printing, but moving only the print position to the next line. Differences : None - 8 - BIXOLON Rev. 1.00...
Page 9
This command works in page mode enabled by ESC L. ■ If the paper is positioned at the print starting position, this command is ignored, not performing actual paper feeding operation. Differences : None - 9 - BIXOLON Rev. 1.00...
Page 10
Code : ASCII Decimal Range : None Default : None Description : This command prints the data. With auto line feed enabled, it performs printing and one line feeding same as LF. Differences : None - 10 - BIXOLON Rev. 1.00...
Page 11
None Description : This command clears the receive buffer and print buffers in page mode. Remarks : This command is effective only in page mode that is set by ESC L. Differences : None - 11 - BIXOLON Rev. 1.00...
Page 12
Drawer kick-out connector pin 3 is LOW Drawer kick-out connector pin 3 is HIGH Online Offline Not used. Fixed to On Not used. Fixed to Off Not used. Fixed to Off Not used. Fixed to Off - 12 - BIXOLON Rev. 1.00...
Page 13
Not used. Fixed to On Not used. Fixed to Off No autocutter error Autocutter error occurred Not used. Fixed to On Not used. Fixed to Off Not used. Fixed to Off Not used. Fixed to Off - 13 - BIXOLON Rev. 1.00...
Page 14
The status is transmitted to the host upon being requested that can check the printer operational condition with it and takes appropriate measures accordingly. The real time command is stored into the receive buffer and executed with higher priority than other commands. ■ Differences : None - 14 - BIXOLON Rev. 1.00...
Page 15
Upon receiving this command, the printer outputs the drive pulse to the specified connector pin. ■ The real time command is stored into the receive buffer and executed with higher priority than other commands. Differences : None - 15 - BIXOLON Rev. 1.00...
Page 16
In a double width mode, the right space will be doubled. ■ Horizontal motion unit varies depending the printer model. Differences : Horizontal motion unit : ■ SRP-F310II : 0.141mm(1/180 inch) ■ SRP-F312II/F313II : 0.125mm(1/203 inch) - 16 - BIXOLON Rev. 1.00...
Page 17
■ The entire character print width is underlined, but the space skipped by HT is not. ■ If both double width and double height are selected, the characters will be quadrupled. Differences : None - 17 - BIXOLON Rev. 1.00...
Page 18
In page mode, the horizontal motion unit is applied when printing start poison is defined to the upper right or lower right of print area using ESC T, otherwise, the vertical motion unit is used. Differences : Horizontal motion unit : ■ SRP-F310II : 0.141mm(1/180 inch) ■ SRP-F312II/F313II : 0.125mm(1/203 inch) - 18 - BIXOLON Rev. 1.00...
Page 19
When n=0, the user-defined character set is deselected. • When n=1, the user-defined character set is selected. • Remarks : The resident character set is enabled and used right after canceling the user defined character set. Differences : None - 19 - BIXOLON Rev. 1.00...
Page 20
• dot data for the user-defined characters. - 20 - BIXOLON Rev. 1.00...
Page 21
Once user defined characters are defined, they remain available until they are redefined; ESC ? or ESC @ is executed; the printer is reset. ■ The following shows the relationship between the definition data and printing result with downloaded character consisting of 9x7 dots. Differences : None - 21 - BIXOLON Rev. 1.00...
Page 22
(DPI) 8-dot single-density nL + nH x 256 8-dot double-density nL + nH x 256 24-dot single-density (nL + nH x 256) x 3 24-dot double-density (nL + nH x 256) x 3 - 22 - BIXOLON Rev. 1.00...
Page 23
203/3 203/2 nL + nH x 256 8-dot double-density 203/3 nL + nH x 256 24-dot single-density 203/2 (nL + nH x 256) x 3 24-dot double-density (nL + nH x 256) x 3 - 23 - BIXOLON Rev. 1.00...
Page 24
Turns on underline mode, set at 2-dot thick Remarks : ■ The spaces generated by horizontal tab are not underlined. ■ Using bit 7 of ESC !, the underline mode can be activated/deactivated as well. Differences : None - 24 - BIXOLON Rev. 1.00...
Page 25
The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed. Differences : Default line spacing : ■ SRP-F310II : 4.23 mm(30 dots) ■ SRP-F312II/F313II : 3.75 mm(30 dots) - 25 - BIXOLON Rev. 1.00...
Page 26
Vertical or horizontal motion unit and maximum line spacing settable : Model Vertical unit Horizontal unit Max line spacing SRP-F310II 0.0705mm (1/360 inch) 0.141mm (1/180 inch) 17.98mm SRP-F312II/F313II 0.0625mm (1/406 inches) 0.125mm (1/203 inches) 15.937mm - 26 - BIXOLON Rev. 1.00...
Page 27
The normal operation will be resumed by ESC @, power cycling or printer reset. ■ If LSB is activated when the printer is disabled by this command, the status is transmitted to the host at a preset interval. Differences : None - 27 - BIXOLON Rev. 1.00...
Page 28
This command removes user-defined character specified by character code n. Remarks : ■ In place of the deleted user-defined character, the cooresponding resident character is printed. ■ The user-defined characters for each font can be deleted independently. Differences : None - 28 - BIXOLON Rev. 1.00...
Page 29
NV graphics and NV user memory are not cleared. ■ In page mode, this command removes the data in print areas, restores the initial settings and returns to standard ■ mode. Differences : None - 29 - BIXOLON Rev. 1.00...
Page 30
Up to 32 horizontal tabs can be set, the data exceeding this limit is processed as normal ones. ■ Even if the character width is changed after setting the horizontal tab positions, the horizontal tab positions remain unchanged. Differences : None - 30 - BIXOLON Rev. 1.00...
Page 31
When the LSB of n is 1, emphasized mode is turned on. • Remarks : The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed. Differences : None - 31 - BIXOLON Rev. 1.00...
Page 32
When the LSB of n is 1, emphasized mode is turned on. • Remarks : The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed. Differences : None - 32 - BIXOLON Rev. 1.00...
Page 33
When used in page mode, this command moves only the print position, not executing actual printing. Differences : ■ Vertical motion unit and maximum feed amount : Model Vertical unit Max feed amount SRP-F310II 0.0705mm (1/360 inch) 17.98mm SRP-F312II/F313II 0.0625mm (1/406 inches) 15.937mm - 33 - BIXOLON Rev. 1.00...
Page 34
In page mode, the command, FF, prompts printing the data in the printer buffer collectively. LF, CR, ESC J, and ESC d just move the print position, not performing actual printing. Differences : None - 34 - BIXOLON Rev. 1.00...
Page 35
The printer model has it own configuration of Font A and B. ■ ■ The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed. Differences : None - 35 - BIXOLON Rev. 1.00...
Page 36
Denmark II Denmark I Spain II Sweden Latin America Italy Korea Remarks : The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed. Differences : None - 36 - BIXOLON Rev. 1.00...
Page 37
The conditions by the following commands are defined independently in standard mode and page mode. ESC SP, ESC 2, and ESC 3 • ■ In standard mode, CAN and GS $ are ignored. Differences : None - 37 - BIXOLON Rev. 1.00...
Page 38
ESC 3, ESC J, GS $ the horizontal motion unit. ■ The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed. Differences : None - 38 - BIXOLON Rev. 1.00...
Page 39
If set in page mode, the 90° clockwise rotation mode has effect after the printer returns to standard mode. ■ The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed. Differences : None - 39 - BIXOLON Rev. 1.00...
Page 41
The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed. Differences : The maximum printable area(Max horizontal printable area, Max vertical printable area) : ■ Model Max horizontal printable area Max vertical printable area SRP-F310II 72.2mm(512dots) 234.3mm(1662dots) SRP-F312II 72mm(576dots) 207.75mm(1662dots) SRP-F313II 80mm(640dots) 207.75mm(1662dots) - 41 - BIXOLON Rev. 1.00...
Page 42
ESC T, otherwise, the vertical motion unit is used. ■ Even if the underline mode is turned on, the space skipped by this command is not printed underlined. Differences : None - 42 - BIXOLON Rev. 1.00...
Page 43
This command is not effective in page mode. If this command is processed in page mode, the setting by this command becomes effective when the printer returns to standard mode. ■ The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed. Differences : None - 43 - BIXOLON Rev. 1.00...
Page 44
In page mode, this command moves only the print position, not performing actual print. ■ If the feed amount set is beyond the maximum feed amount, the feed amount will be set to the maximum feed amount automatically. Differences : None - 44 - BIXOLON Rev. 1.00...
Page 45
Autocutter operation should be enabled by setting the autocutter control DIP switch. ■ If the autocutter control DIP switch of the printer not equipped with autocutter is set, the printer does not operate, displaying the error signal by LED. - 45 - BIXOLON Rev. 1.00...
Page 46
Autocutter operation should be enabled by setting the autocutter control DIP switch. ■ If the autocutter control DIP switch of the printer not equipped with autocutter is set, the printer does not operate, displaying the error signal by LED. - 46 - BIXOLON Rev. 1.00...
Page 47
The ON time is [t1 x 2ms], and the OFF time is as [t2 x 2ms]. If t2 is smaller than t1, OFF time is set to [t1 x 2ms]. • Differences : None - 47 - BIXOLON Rev. 1.00...
Page 49
Page 42 Khmer (Cambodia) Page 47 1250 (Czech) User Code Page (Space) Remarks : The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed. Differences : None - 49 - BIXOLON Rev. 1.00...
Page 50
The near end senor is optional while paper end sensor required. ■ If the printer is not equipped with a near end sensor, the paper near end sensor is considered as normal condition. Differences : None - 50 - BIXOLON Rev. 1.00...
Page 51
180 rotated characters are printed from right to left in upside-down print mode. ■ The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed. Example Normal Upside- down Mode Differences : None - 51 - BIXOLON Rev. 1.00...
Page 52
The printer does not print the NV bit image that is beyond one line of print area. ■ When using unidirectional print mode, there will be no vertical misali gnment between the top and bottom parts of the printed pattern. - 52 - BIXOLON Rev. 1.00...
Page 53
Horizontal Dot Density (DPI) Normal Double-width Double-height Quadruple ■ SRP-F312II/F313II : DPI : Dots per Inch (25.4mm) Mode Vertical Dot Density (DPI) Horizontal Dot Density (DPI) Normal Double-width 203/2 Double-height 203/2 Quadruple 203/2 203/2 - 53 - BIXOLON Rev. 1.00...
Page 54
When this command is entered, all NV bit images previously defined are removed from the NV memory. ■ After completion of this command, the printer executes a software reset to restore the settings as when turned on. ■ The NV bit image is printed by FS p. - 54 - BIXOLON Rev. 1.00...
Page 55
Bit image data and print result are as follows : • dY+1 … dY+2 … dk-2 … dk-1 dY x 2 … ■ The capacity of NV memory area is 256KB. Differences : None - 55 - BIXOLON Rev. 1.00...
Page 56
Specifies the number of times normal font size in Refer to Table 2 the vertical direction [Enlarged in vertical direction] Specifies the number of times normal font size in Refer to Table 1 the horizontal direction [Enlarged in horizontal direction] - 56 - BIXOLON Rev. 1.00...
Page 57
Double width and double height modes can be set by ESC !. ■ Multi-byte code characters are specified only by this command. ■ The setting of this command remains effective until ESC @, printer reset or power cycling is executed. Differences : None - 57 - BIXOLON Rev. 1.00...
Page 58
With the starting position of the upper left or lower right on the print area, the vertical motion unit is used. • In other cases, the horizontal motion unit is used. • ■ The configuration beyond the print area set by ESC W is ignored. Differences : None - 58 - BIXOLON Rev. 1.00...
Page 59
All of the data transmitted from the host to the printer is printed and identified in hexadecimal dump mode. ■ The real time command and LSB operations are not executed during the printing of printer configuration (m=2, 50). Differences : None - 59 - BIXOLON Rev. 1.00...
Page 60
GS ( L pL pH m fn kc1 kc2 x y Prints the specified NV graphics data GS ( L pL pH m fn a bx by c xL xH yL Stores the graphics data in the print buffer memory yH d1…dk - 60 - BIXOLON Rev. 1.00...
Page 61
While storing data by this command, the printer is in BUSY state where receiving of data is not available. Therefore, it is not recommended to send data during this process. ■ The real time commands and LSB operations are not allowed during NV memory operation process. Differences : None - 61 - BIXOLON Rev. 1.00...
Page 62
The data length is variable. ■ The total capacitu of the NV user memory is selectable as any one of[0, 64K, 128K, 192K, 256K] bytes with GS ( E. The default value is 256K. Differences : None - 62 - BIXOLON Rev. 1.00...
Page 63
The graphics data is defined by Function 112. ■ The required amount of line feed pitch is used for printing graphics data, regardless of the existing setting value of the pitch. Differences : None - 63 - BIXOLON Rev. 1.00...
Page 64
The setting value is sent from bit 8 to bit 1, consisting of 8 bytes in total. Off : Hexadecimal = 30H/Decimal = 48 • On : Hexadecimal = 31H/Decimal = 49 • Remarks : None Differences : None - 64 - BIXOLON Rev. 1.00...
Page 65
48 - 57 2 - 80 bytes 1 byte ■ When the key code is not present : Hexadecimal Decimal Amount of Data Header 1 byte Flag 1 byte Status 1 byte 1 byte - 65 - BIXOLON Rev. 1.00...
Page 66
- When the status (for the last data block) is Hexadecimal = 40H/Decimal = 64) Response Process performed ASCII Decimal Ends the process Transmits the previous data again Cancels the process. Differences : None - 66 - BIXOLON Rev. 1.00...
Page 67
This command removes all defined NV graphics data. Remarks : The graphics data is define by Function 67 into the NV graphics memory with the sector dedicated for storing NV graphics data. Differences : None - 67 - BIXOLON Rev. 1.00...
Page 68
32 ≤ kc2 ≤ 126 Default : None Description : Deletes the NV graphics data defined by the codes kc1 and kc2. Remarks : The graphics data is define by Function 67. Differences : None - 68 - BIXOLON Rev. 1.00...
Page 69
1 ≤ (yL + yH x 256) ≤ 2304 c=49 0 ≤ d ≤ 255 k = ( int ( ( xL + xH x 256 ) + 7 )/8 ) x ( yL + yH x 256 ) Default : None - 69 - BIXOLON Rev. 1.00...
Page 70
The rest of NV graphics data groups having no change should be redefined along with the new group stored. ■ When NV graphics data groups are saved, each of the groups is allocated with N in the order of download. Differences : None - 70 - BIXOLON Rev. 1.00...
Page 71
This command prints the NV graphics data defined by Function 67. ■ In page mode, this command is not effective. ■ NV graphics data beyond the print area for one line is not printed. Differences : None - 71 - BIXOLON Rev. 1.00...
Page 72
1 ≤ (xL + xH x 256) ≤ 415 (When by =2) 0 ≤ d ≤ 255 k = ( int ( ( xL + xH x 256 ) + 7 )/8 ) x ( yL + yH x 256 ) Default : None - 72 - BIXOLON Rev. 1.00...
Page 73
The graphics data is stored in the printer buffer directly. ■ NV graphics data beyond the print area for one line is not printed. ■ Real time command is not effective during processing of this command. Differences : None - 73 - BIXOLON Rev. 1.00...
Page 74
QR CODE : Select the error correction level Function 180 QR CODE : Store the data in the symbol storage area Function 181 QR CODE : Print the data in the symbol storage area - 74 - BIXOLON Rev. 1.00...
Page 75
The same symbol data is repeatedly printed by executing Function 181 after performing Function 180. ■ The same symbol data is printed differently by executing Function 181 after setting the feature of the symbol by using Functions 165 through 169. Differences : None - 75 - BIXOLON Rev. 1.00...
Page 76
Printing area when processing Functions 081 • Module width (Function 067) • Option setting (Function 070) • ■ The setting of this command remains effective until ESC @, printer reset or power cycling is executed. Differences : None - 76 - BIXOLON Rev. 1.00...
Page 77
With auto processing (n=0) specified, the number of rows is calculated by using the following information : Printing area when processing Functions 081 • Module height (Function 068) • ■ The setting of this command remains effective until ESC @, printer reset or power cycling is executed. Differences : None - 77 - BIXOLON Rev. 1.00...
Page 78
■ The setting of this command remains effective until ESC @, printer reset or power cycling is executed. Differences : Setting unit(1 dot) : ■ SRP-F310II : 0.141(1/180 inch) ■ SRP-F312II/F313II : 0.125(1/203 inch) - 78 - BIXOLON Rev. 1.00...
Page 79
Remarks : ■ Settings of this command affect the processing of Functions 081. ■ The setting of this command remains effective until ESC @, printer reset or power cycling is executed. Differences : None - 79 - BIXOLON Rev. 1.00...
Page 80
Error correction level 5 Error correction level 6 Error correction level 7 Error correction level 8 ■ The setting of this command remains effective until ESC @, printer reset or power cycling is executed. Differences : None - 80 - BIXOLON Rev. 1.00...
Page 81
■ When simplified PDF417 symbol is canceled, standard PDF417 symbol is automatically selected. ■ The setting of this command remains effective until ESC @, printer reset or power cycling is executed. Differences : None - 81 - BIXOLON Rev. 1.00...
Page 82
The error correction codeword calculated by modulus 929. • ■ The setting of this command remains effective until the following processing is performed : Executing Function 080 • Executing ESC @ • Executing printer reset or power-off • Differences : None - 82 - BIXOLON Rev. 1.00...
Page 83
Indicator code word of left and right. • The descriptor of symbol length (the first code word in the data area). • The error correction code word calculated by modulus 929. • Pad codeword. • - 83 - BIXOLON Rev. 1.00...
Page 84
The quiet zone is not included in the printing data. Be sure to include the adequate quiet zone for executing of this command. The quiet zone means the spaces surrounding the symbol such as upper, lower, left, and right spaces. • Differences : None - 84 - BIXOLON Rev. 1.00...
Page 85
Model 2 Remarks : ■ The setting of this command affects <Function 181>. ■ The setting of this command remains effective until ESC @, printer reset or power cycling is executed. Differences : None - 85 - BIXOLON Rev. 1.00...
Page 86
Since the QR CODE module is square, n = module width = module height. ■ The setting of this command remains effective until ESC @, printer reset or power cycling is executed. Differences : None - 86 - BIXOLON Rev. 1.00...
Page 87
Reed-Solomon correction is employed to generate a series of error correction codewords. ■ The setting of this command remains effective until ESC @, printer reset or power cycling is executed. ■ Differences : None - 87 - BIXOLON Rev. 1.00...
Page 88
00H ~ FFH ■ The setting of this command remains effective until the following processing is performed : Performing Function 180 • Performing ESC @ • Performing the printer reset or power-off • Differences : None - 88 - BIXOLON Rev. 1.00...
Page 89
The four types of data compression modes are listed below. According to the symbol data in the data storage area, • automatically selects the best suitable compression mode. *Numeric Data Code *Alphanumeric Data mode *Kanji Data mode *8 bit Data mode - 89 - BIXOLON Rev. 1.00...
Page 90
In page mode, the printer stores the symbol data in the print buffer without executing actual printing. ■ The quiet zone is not included in the printing data. Be sure to include the adequate quiet zone for executing of this command. Differences : None - 90 - BIXOLON Rev. 1.00...
Page 91
The user-defined character and the downloaded bit image cannot be defined simultaneously. The user-defined character is cleared preceding the execution of this command. • The downloaded bit image data is cleared with ESC & executed. • Differences : None - 91 - BIXOLON Rev. 1.00...
Page 92
Except for character size and upside-down printing mode, none of print mode such as emphasized, double-strike, etc, affects the printing of the downloaded bit image. ■ The default dot density set by GS L is applied to printing of the downloaded bit image. - 92 - BIXOLON Rev. 1.00...
Page 94
The maximum number of macro data to be defined varies with respect to printer models. The data exceeding this limit is not stored. ■ ESC @ does not clear the existing defined macro. The macro remains effective until the printer reset and power cycling are executed. Differences : None - 94 - BIXOLON Rev. 1.00...
Page 95
The right space defined by ESC SP is affected by this command. ■ In white/black reverse mode, the underline mode is not effective. ■ This mode remains effective until ESC @, printer reset or power cycling is executed. Differences : None - 95 - BIXOLON Rev. 1.00...
Page 96
Remarks : ■ The font of the HRI characters is defined by GS f. ■ The setting of this command remains effective until ESC @, printer reset or power cycling is executed. Differences : None - 96 - BIXOLON Rev. 1.00...
Page 97
Transmits specified printer information, using n as follows : • Printer ID type Specification Firmware version Firmware version Manufacturer BIXOLON Printer model Printer model Code page Currently enabled code page Remarks : ■ Printer information (When n = 65, 66, 67, 69) consist of [Header ~ NULL] data as shown below :...
Page 98
3(Printer feature ID) 0x63(when 3inch),0x62(when 2inch) 65(Firmware Version) Depend on firmware version information 66(Manufacturer) BIXOLON 67(Printer model) SRP-F310II or SRP-F312II or SRP-F313II 69(Language of Font) Code page currently being used. Refer to cod page setting command, ESC t. - 98 - BIXOLON Rev.
Page 99
■ The setting of this command remains effective until ESC @, printer reset or power cycling is executed. Printable area Left margin Printing area width Differences : None - 99 - BIXOLON Rev. 1.00...
Page 100
If an auto cutter is not provided, the printer only feeds the paper for specified amount. ■ Vertical motion unit is used for calculating a paper feed amount. ■ Cutting mode is changed only by setting MSW5-1. Differences : None - 100 - BIXOLON Rev. 1.00...
Page 101
(printing area width - left margin). ■ The setting of this command remains effective until ESC @, printer reset or power cycling is executed. Printable area Left margin Printing area width Differences : None - 101 - BIXOLON Rev. 1.00...
Page 102
The macro is defined by GS : ■ If the macro is not defined or r = 0, the command is ignored. ■ The macro function is useful to print the same data repeatedly. Differences : None - 102 - BIXOLON Rev. 1.00...
Page 103
With serial interface, ASB status is transmitted continuously at the interval of 1 sec even if the status is not changed. ■ The setting of this command remains effective until ESC @, printer reset or power cycling is executed. - 103 - BIXOLON Rev. 1.00...
Page 104
If mechanical error (bit 2) or auto-cutter error (bit 3) occurs due to paper jams or the like, it is possible to recover by correcting a cause of the error and executing ENQ in real time mode. If an unrecoverable error (bit 5) occurs, turn off the power as soon as possible. - 104 - BIXOLON Rev. 1.00...
Page 105
Not used. Fixed to On Not used. Fixed to On Not used. Fixed to On Not used. Fixed to Off Not used. Fixed to Off Not used. Fixed to Off Not used. Fixed to Off Differences : None - 105 - BIXOLON Rev. 1.00...
Page 106
The setting of this command is applied to only HRI characters. ■ The printing position of HRI characters are specified by GS H. ■ The configurations of Font A and B vary depending on the printer model. Differences : None - 106 - BIXOLON Rev. 1.00...
Page 107
The setting of this command remains effective until ESC @, printer reset or power cycling is executed. Differences : Unit of one dot : SRP-F310II : 0.141mm(1/180 inch) ■ ■ SRP-F312II/F313II : 0.125mm(1/203 inch) - 107 - BIXOLON Rev. 1.00...
Page 108
48 ≤ d ≤ 57, 65 ≤ d ≤ 90, 1 ≤ k CODE39 d=32,36,37,43,45,46,47 1 ≤ k (even number) 48 ≤ d ≤ 57 48 ≤ d ≤ 57, 65 ≤ d ≤ 68, 1 ≤ k CODABAR d=36,43,45,46,47,58 - 108 - BIXOLON Rev. 1.00...
Page 109
Except for character size and upside-down printing mode, none of print mode such as emphasized, double-strike, etc, affects the printing of the barcode. ■ The quiet zone of the bar code (left and right spaces of the bar code) should be considered when using this command. Differences : None - 109 - BIXOLON Rev. 1.00...
Page 110
Bits 2 and 3 : This command can not be executed when the printer is offline due to the lack of paper. Therefore, the status of bit 2 (1) and bit 3 (1) is not transmitted. - 110 - BIXOLON Rev. 1.00...
Page 111
Drawer kick-out connector pin 3 is LOW Drawer kick-out connector pin 3 is HIGH Reserved Reserved Reserved Fixed Reserved Reserved Fixed This command can be executed in real-time mode using DLE. ■ Differences : None - 111 - BIXOLON Rev. 1.00...
Page 112
None of the print modes such as emphasized, double-strike, etc, affects the printing of the bit image. ■ The default dot density set by GS L is applied to printing of the bit image. - 112 - BIXOLON Rev. 1.00...
Page 113
■ SRP-F312II/F313II : DPI : Dots per Inch (25.4mm) Mode Vertical dot density (DPI) Horizontal dot density (DPI) 0, 48 Normal 1, 49 Double-width 203/2 2, 50 Double-height 203/2 3, 51 Quadruple 203/2 203/2 - 113 - BIXOLON Rev. 1.00...
Page 114
Multi-level bar codes (UPC-A, UPC-E, JAN13, HAN8, CODE93, CODE128) • Binary-level bar codes (CODE39, ITF, CODABAR) • ■ The setting of this command remains effective until ESC @, printer reset or power cycling is executed. - 114 - BIXOLON Rev. 1.00...
Page 116
The printer supports 3 font types by selecting m function. Remarks : ■ The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed. Differences : None - 116 - BIXOLON Rev. 1.00...
Page 117
Feeds paper to (cutting position + n × vertical motion unit) and executes a partial cut (one point left uncut) ② Feeds paper to (cutting position + n × vertical motion unit) and executes a full cut (cuts the paper completely) Differences : None - 117 - BIXOLON Rev. 1.00...
Page 118
When the printer is entered power saving mode, printer is wait external interrupt. Remarks : ■ If external interrupt is occurred, printer is wake up. Communication(Serial, Parallel, USB), Cover sensor, Feed switch. • Differences : None - 118 - BIXOLON Rev. 1.00...
Page 119
The power saving set time is [t x 1s] and the default time is 20 sec. If n is smaller than 5 the power saving time is set to defaut [20 x 1s]. • Differences : None - 119 - BIXOLON Rev. 1.00...
Page 120
Decimal Amount of data Header 1byte Power saving mode Depends on the setting Depends on the setting 1byte Power saving time Depends on the setting Depends on the setting 1byte 1byte Differences : None - 120 - BIXOLON Rev. 1.00...