Table of Contents
Advertisement
Available languages
Available languages
e)
Maintain power tools and accessories. Check for misalignment
or binding of moving parts, breakage of parts and any other
condition that may affect the power tool's operation. If
damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
f)
Keep cutting tools sharp and clean.Properly maintained cutting
tools with sharp cutting edges are less likely to bind and are easier to
control.
g)
Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account the
working conditions and the work to be performed. Use of the
power tool for operations different from those intended could result in a
hazardous situation.
h)
Keep handles and grasping surfaces dry, clean and free from oil
and grease. Slippery handles and grasping surfaces do not allow for
safe handling and control of the tool in unexpected situations.
5)
Battery tool use and care
a)
Recharge only with the charger specified by the manufacturer.
EN
A charger that is suitable for one type of battery pack may create a risk of
fire when used with another battery pack.
b)
Use power tools only with specifically designated battery
8
packs. Use of any other battery packs may create a risk of injury and
fire.
c)
When battery pack is not in use, keep it away from other metal
objects, like paper clips, coins, keys, nails, screws or other
small metal objects, that can make a connection from one
terminal to another. Shorting the battery terminals together may
cause burns or a fire.
d)
Under abusive conditions, liquid may be ejected from the
battery; avoid contact. If contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or burns.
e)
Do not use a battery pack or tool that is damaged or modified.
Damaged or modified batteries may exhibit unpredictable behaviour
resulting in fire, explosion or risk of injury.
f)
Do not expose a battery pack or tool to fire or excessive
temperature. Exposure to fire or temperature above 130 °C may cause
explosion.
g)
Follow all charging instructions and do not charge the battery
pack or tool outside the temperature range specified in the
instructions. Charging improperly or at temperatures outside the
specified range may damage the battery and increase the risk of fire.
6)
Service
a)
Have your power tool serviced by a qualified repair person
using only identical replacement parts. This will ensure that the
safety of the power tool is maintained.
b)
Never service damaged battery packs. Service of battery packs
should only be performed by the manufacturer or authorized service
providers.
DRILL SAFETY WARNINGS
1)
Safety instructions for all operations
a)
Hold the power tool by insulated gripping surfaces, when
performing an operation wherethe cuttingaccessory or
fastenersmay contact hidden wiring. Cutting accessoryor
fastenerscontacting a "live" wire may make exposed metal parts of the
power tool "live" and couldgive the operator an electric shock.
2)
Safety instructions when using long drill bits
a)
Never operate at higher speed than the maximum speed rating
of the drill bit. At higher speeds, the bit is likely to bend if
allowed to rotate freely without contacting the workpiece,
resulting in personal injury.
b)
Always start drilling at low speed and with the bit tip in contact
with the workpiece. At higher speeds, the bit is likely to bend
if allowed to rotate freely without contacting the workpiece,
resulting in personal injury.
c)
Apply pressure only in direct line with the bit and do not apply
excessive pressure. Bits can bend causing breakage or loss of
control, resulting in personal injury.
SAFETY WARNINGS FOR BATTERY CELLS INSIDE THE TOOL
a)
Do not dismantle, open or shred cells.
b)
Do not short-circuit charging terminal. Do not store power tool
haphazardly in a box or drawer where charging terminal may
short-circuit each other or be short-circuited by conductive
materials. When power tool is not in use, keep it away from other
metal objects, like paper clips, coins, keys, nails, screws or other small
metal objects, that can make a connection from one charging terminal to
another.
c)
Do not expose power tool to heat or fire. Avoid storage in
direct sunlight.
Advertisement
Table of Contents
