Table of Contents
Advertisement
RETRY CAUSE DISPLAY MODE
• In this test mode, the causes for retry of the unit during recording can be displayed on the fluorescent indicator tube. During playback,
the "track mode" for obtaining track information will be set.
This is useful for locating the faulty part of the unit.
• The following will be displayed :
During recording and stop : Retry cause, number of retries, and number of retry errors.
During playback
These are displayed in hexadecimal.
Procedure:
1. Load a recordable disc whose contents can be erased into the unit.
2. Press the
MENU/NO "R"
button to display "All Erase?".
3. Press the
ENTER/YES "R"
4. When "All Erase??" is displayed on the fluorescent indicator tube, the music calendar number blinks.
5. Press the
ENTER/YES "R"
while pressing the button.
6. When the "TOC" displayed on the fluorescent display tube goes off, release the
7. Press the
z
button to start recording. Then press the
REC
[FUNCTION]
press the
button and set a different function.
8. To check the "track mode", press the
9. To release the test mode, press the
outlet. If the test mode cannot be released, refer to "MC COLD RESET" on page 8).
Fig. 1 Reading the Test Mode Display
(During recording and stop)
RTs@@c##e
Fluorescent indicator tube display
@@ : Cause of retry
##
: Number of retries
: Number of retry errors
**
Reading the Retry Cause Display
Higher Bits
Hexadecimal
8
4
2
Bit
b7 b6 b5 b4 b3 b2 b1 b0
Binary
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
0
1
0
0
Reading the Display:
Convert the hexadecimal display into binary display. If more than two causes, they will be added.
Example
When 42 is displayed:
Higher bit: 4 = 0100 t b6
Lower bit : 2 = 0010 t b1
In this case, the retry cause is combined of "CLV unlock" and "ader5".
When A2 is displayed:
Higher bit: A = 1010 t b7+b5
Lower bit : 2 = 0010 t b1
The retry cause in this case is combined of "access fault", "IVR rec error", and "ader5".
12
: Information such as type of disc played, part played, copyright.
button. When "Edit Menu" is displayed on the fluorescent indicator tube, press the
button.
button to display "Complete!!", and press the
(MD) button to start play.
HS
button, and turn the power off. When "TOC" disappears, disconnect the power plug from the
I/1
**
Lower Bits
Hexa-
1
8
4
2
1
decimal
01
0
0
0
0
1
0
0
0
1
0
02
04
0
0
1
0
0
0
1
0
0
0
08
10
1
0
0
0
0
20
0
0
0
0
0
0
0
0
0
0
40
80
0
0
0
0
0
(MD) button immediately. Wait for about 10 seconds
s
s
HS
(MD) button and start recording. If recording cannot be performed,
Fig. 2 Reading the Test Mode Display
@@ : Parts No. (name of area named on TOC)
## : Cluster
**
$$ : Track mode (Track information such as copy-
Cause of Retry
shock
When track jump (shock) is detected
When ADER was counted more than five times
ader5
continuously
When ADIP address is not continuous
Discontinuous address
When DIN unlock is detected
DIN unlock
When not in focus
FCS incorrect
When ABCD signal level exceeds the specified range
IVR rec error
When CLV is unlocked
CLV unlock
When access operation is not performed normally
Access fault
l m
(MD) button.
(During playback)
@@ ###
$$
**
Fluorescent indicator tube display
Address
: Sector
right information of each part)
Occurring conditions
or
M L
Advertisement
Table of Contents
