Table of Contents

Advertisement

HCD-FX999W/FX1000W
QQ
3 7 63 1515 0
SERVICE MANUAL
Ver. 1.4 2005.12
HCD-FX999W/FX1000W are the amplifier, DVD/CD
and tuner section in DAV-FX999W/FX1000W.
This system incorporates with Dolby*1 Digital and
Dolby Pro Logic (II) adaptive matrix surround decoder
and the DTS*2 Digital Surround System.
*1 Manufactured under license from Dolby Laboratories.
"Dolby," "Pro Logic," and the double-D symbol are trademarks
of Dolby Laboratories.
*2 Manufactured under license from Digital Theater Systems, Inc.
TE
L 13942296513
"DTS" and "DTS Digital Surround" are trademarks of Digital
Theater Systems, Inc.
Amplifier section
Central and South American models:
Stereo mode (rated)
Surround mode (reference) music power output
Mexican and other models:
Stereo mode (rated)
Surround mode (reference) music power output
* Depending on the sound field settings and the source,
there may be no sound output.
www
.
Sony Corporation
9-879-743-05
Home Audio Division
2005L16-1
Published by Sony Engineering Corporation
© 2005.12
http://www.xiaoyu163.com
Inputs (Analog)
VIDEO,
55 W + 55 W (3 ohms at 1
kHz, DIN)
Input (Digital)
Front: 120 W + 120 W
SAT (Optical)
(with SS-TS47)
Phones
Center*: 120 W
(with SS-CT46)
MIC
Surround*: 120 W + 120 W
(with SS-TS46B)
Super Audio CD/DVD system
Subwoofer*: 240 W
Laser
(with SS-WS43)
55 W + 55 W (3 ohms at 1
kHz, DIN)
Front: 143 W + 143 W
Signal format system
(with SS-TS47)
Frequency response (at 2 CH STEREO mode)
Center*: 143 W
(with SS-CT46)
Surround*: 143 W + 143 W
(with SS-TS46B)
Subwoofer*: 285 W
Harmonic distortion
(with SS-WS43)
x
ao
u163
y
i
http://www.xiaoyu163.com
2 9
8
Photo : HCD-FX999W
Model Name Using Similar Mechanism
Mechanism Type
Optical Pick-up Name
Q Q
3
6 7
1 3
SPECIFICATIONS
SAT
Sensitivity: VIDEO 250
mV/SAT 450 mV
Impedance: 50 kilohms
Impedance:
Accepts low-and high-
impedance headphones.
Sensitivity: 1 mV
Impedance: 10 kilohms
Semiconductor laser
(Super Audio CD/DVD:
= 650 nm)
λ
(CD:
= 790 nm)
Emission duration:
continuous
NTSC/PAL
DVD (PCM): 2 Hz to 22
kHz (±1.0 dB)
CD: 2 Hz to 20 kHz (±1.0
dB)
Less than 0.03 %
.
9 4
2 8
HCD-FX999W/FX1000W
Australian Model
NEW
CDM69EH-DVBU101
KHM-310CAB/C2NP
1 5
0 5
8
2 9
9 4
Tuner section
System
PLL quartz-locked digital
synthesizer system
FM tuner section
Tuning range
87.5 – 108.0 MHz (50 kHz
step)
Antenna (aerial)
FM wire antenna (aerial)
Antenna (aerial) terminals 75 ohms, unbalanced
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
Middle Eastern models:
531 – 1,602 kHz (with the
interval set at 9 kHz)
λ
Mexican model:
530 – 1,710 kHz (with the
interval set at 10 kHz)
531 – 1,710 kHz (with the
interval set at 9 kHz)
Other models:
531 – 1,602 kHz (with the
interval set at 9 kHz)
530 – 1,710 kHz (with the
interval set at 10 kHz)
Antenna (aerial)
AM loop antenna (aerial)
Intermediate frequency
450 kHz
— Continued on next page —
m
DVD RECEIVER
co
9 9
E Model
HCD-FX999W
2 8
9 9

Advertisement

Table of Contents
loading

Summary of Contents for Sony HCD-FX999W

  • Page 1 HCD-FX999W/FX1000W Australian Model HCD-FX999W Ver. 1.4 2005.12 Photo : HCD-FX999W HCD-FX999W/FX1000W are the amplifier, DVD/CD and tuner section in DAV-FX999W/FX1000W. This system incorporates with Dolby*1 Digital and Model Name Using Similar Mechanism Dolby Pro Logic (II) adaptive matrix surround decoder...
  • Page 2 COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
  • Page 3: Table Of Contents

    HCD-FX999W/FX1000W Ver. 1.1 3 7 63 1515 0 TABLE OF CONTENTS SERVICING NOTE 7-12. Schematic Diagram – DMB10 Section (1/4) – ....41 ........... 4 7-13. Schematic Diagram – DMB10 Section (2/4) – ....42 7-14. Schematic Diagram – DMB10 Section (3/4) – ....43 GENERAL ..............
  • Page 4: Servicing Note

    To prevent a malfunction, the system has performed the self- (xx is a number) diagnosis function. u163 ,Contact your nearest Sony dealer or local authorized Sony service facility and give the 5- character service number. Example: E 61 10 http://www.xiaoyu163.com...
  • Page 5: General

    HCD-FX999W/FX1000W Ver. 1.1 SECTION 2 3 7 63 1515 0 GENERAL This section is extracted from instruction manual. Front panel A Disc slot (43) H x (stop) (44, 89) I X (pause) (44) (remote sensor) (13) C Front panel display (110)
  • Page 6 HCD-FX999W/FX1000W 3 7 63 1515 0 F TOP MENU (48) Remote G C/X/x/c/ENTER (36, 45, 59, 70, 73, 75, 82, 90) have tactile dots.* C/X/x/c H O RETURN (50) I ALBUM –/+ (44, 80) J ANGLE (74) K AUDIO (68) The AUDIO button has a tactile dot.*...
  • Page 7: Disassembly

    HCD-FX999W/FX1000W Ver. 1.1 SECTION 3 3 7 63 1515 0 DISASSEMBLY 3-1. DISASSEMBLY FLOW • This set can be disassembled in the order shown below. • The dotted square with arrow ( ) prompts you to move to the next job when all of the works within the dotted square ( ) are completed.
  • Page 8: Top Panel Sub Assy

    HCD-FX999W/FX1000W 3 7 63 1515 0 Note: Follow the disassembly procedure in the numerical order given. 3-2. TOP PANEL SUB ASSY top panel sub assy 2 two flat head screws (TP) 1 two flat head screws (TP) 4 three screws 3 ×...
  • Page 9: Front Panel Assy

    HCD-FX999W/FX1000W 3 7 63 1515 0 3-3. FRONT PANEL ASSY 2 three screws 3 × 8) (+BVTP MD cover screw 3 × 8) (+BVTP 4 wire (flat type) 19core(CN801) screw 3 × 8) (+BVTP front panel assy L 13942296513...
  • Page 10: Mib01 Board, Mib01 Power Board (Hcd-Fx1000W Only)

    HCD-FX999W/FX1000W Ver. 1.1 3 7 63 1515 0 3-5. MIB01 BOARD, MIB01 POWER BOARD (HCD-FX1000W ONLY) 1 two screws (+BV 3) 5 wire (flat type) 4 MIB01 POWER board 13core(CN5301) 2 connector (CN9002) 3 connector (CN9001) 7 two screws (+BVTP 3 × 8)
  • Page 11: Dmb10 Board, Tx Board

    11core(CN4501) (HCD-FX1000W only) 7 connector (CN401) 9 two screws 3 wire (flat type) (+BV (13core)(CN301) q; two screws (HCD-FX999W only) (+BV DMB10 board 2 wire (flat type) 24core(CN101) 8 wire (flat type) 11core(CN106) 1 connector (CN201) qs three screws 3 × 8)
  • Page 12: Main Board, H/P Board

    HCD-FX999W/FX1000W 3 7 63 1515 0 3-7. MAIN BOARD, MIC BOARD 0 two screws 7 wire (flat type) (+BV 23core(CN507) screw 8 wire (flat type) 3 × 14) (+BVTP 11core(CN504) 6 wire (flat type) heat sink 27core(CN502) 9 wire (flat type)
  • Page 13: Dvd Mechanism Deck (Cdm69Eh-Dvbu101)

    HCD-FX999W/FX1000W 3 7 63 1515 0 3-9. DVD MECHANISM DECK (CDM69EH-DVBU101) 3 DVD mechanism deck (CDM69EH-DVBU101) 1 two screws 2 two screws (+BV (+BV L 13942296513 3-10. BASE UNIT 1 floating screw (DIA. 12) 2 boss 5 boss 3 boss...
  • Page 14: Optical Pick-Up (Khm-310Cab)

    HCD-FX999W/FX1000W 3 7 63 1515 0 3-11. OPTICAL PICK-UP (KHM-310CAB) 3 insulator screw optical pick-up (KHM-310CAB) 8 insulator 2 insulator screw 4 insulator screw 7 insulator 9 insulator 1 insulator screw 6 insulator L 13942296513 3-12. SW BOARD, BRACKET (TOP) ASSY...
  • Page 15: Relay Board

    HCD-FX999W/FX1000W 3 7 63 1515 0 3-13. RELAY BOARD 4 connector (CN710) – bottom view – 5 connector (CN703) RELAY board 2 four screws (+BVTP2.6) 6 RELAY board 1 Remove five solders. L 13942296513 3-14. MOTOR (STOCKER) ASSY (STOCKER)(M761) 3 two screws (+BVTP2.6)
  • Page 16: Motor (Roller) Assy (Roller)(M781)

    HCD-FX999W/FX1000W 3 7 63 1515 0 3-15. MOTOR (ROLLER) ASSY (ROLLER)(M781) 3 two screws (+BVTP2.6) 2 Remove two solders. 4 ROLLER MOTOR board 5 motor (roller) assy (roller)(M781) 1 belt (roller V) L 13942296513 3-16. MOTOR (MODE) ASSY (MODE)(M771) 3 two screws (+BVTP2.6)
  • Page 17: Rubber Roller (Slider) Assy

    HCD-FX999W/FX1000W 3 7 63 1515 0 3-17. RUBBER ROLLER (SLIDER) ASSY 5 step screw 8 step screw 1 step screw 9 tension 7 rubber roller spring 0 rubber roller (slider 1) assy (slider 2) (slider 4) assy 2 rubber roller...
  • Page 18: Cam (Gear)

    HCD-FX999W/FX1000W 3 7 63 1515 0 3-19. CAM (GEAR) qf cam (gear) : Note 6 gear (mode 5) qd screw 5 screw (PTPWH2.6 × 8) 4 gear (mode 5) qs gear(mode cam) 3 screw (PTPWH2.6 × 8) qa screw (PTPWH2.6 ×...
  • Page 19: How To Install The Cam (Eject Lock)

    HCD-FX999W/FX1000W SECTION 4 3 7 63 1515 0 ASSEMBLY • This set can be assembled in the order shown below. 4-1. HOW TO INSTALL THE CAM (EJECT LOCK) 1 Rotate the cam (BU U/D) fully in the direction of arrow.
  • Page 20: How To Install The Gear (Mode C)

    HCD-FX999W/FX1000W 3 7 63 1515 0 4-3. HOW TO INSTALL THE GEAR (MODE C) 1 Align the mark on the rotary encoder (S771) with the projection of the assy. 2 Check that the cam (BU U/D) can not be rotated in the direction of arrow.
  • Page 21: How To Install The Rotary Encorder (S702)

    HCD-FX999W/FX1000W 3 7 63 1515 0 4-5. HOW TO INSTALL THE ROTARY ENCORDER (S702), GEAR (STOCKER COMMUNICATION) 4 gear 5 screw (PTPWH2.6 × 8) (stocker communication) 3 screw 7 two screws (PWH2 × 6) (PTPWH2.6 × 8) 1 rotary encoder...
  • Page 22: Test Mode

    “AM 10 k STEP”, and thus the channel step is changed over. Procedure: 1. When the panel test mode is activated, press the H button, *1 In HCD-FX999W, “GC7GW***” is displayed. to select the key test mode. 2. To enter the KEY test mode, the fluorecent indicator displays “K0”.
  • Page 23 : Ver. x.xxx 5. Default set MIRR time This command will set CD and DVD mirror time to firmware default *1 In HCD-FX999W, “GC7GW***” is displayed. value. The menu above is the Remocon Diagnosis Menu screen which [Open] / [Close] consists of six main function.
  • Page 24 : Ver. xx.xx (xxxx) return to step 7. Syscon : Ver. x.xxx MIRR time Adjust Menu *1 In HCD-FX999W, “GC7GW***” is displayed. 1. CD MIRR time Check: 2. DVD MIRR time Check: XX XX (3) Select “5. MIRR time Adjust”. 3. Threshold: 4.
  • Page 25 : XX.XX (XXXX) Syscon Ver : X.XX (9) Press ORETURN “R” button to return back to previous menu. *1 In HCD-FX999W, “GC7GW***” is displayed. (10) Press 0 “R” button to return to Top Menu and power OFF the DVD Player. u163...
  • Page 26: Electrical Adjustment

    HCD-FX999W/FX1000W Ver. 1.1 SECTION 6 3 7 63 1515 0 ELECTRICAL ADJUSTMENT DIAT SECTION HDMI SECTION *For HCD-FX1000W only DIAT SIGNAL RF LEVEL ADJUSTMENT ADJUSTMENT OF VIDEO SYSTEM This adjustment is performed in order to adjust the transmission distance of RF signal for DIAT communication.
  • Page 27 HCD-FX999W/FX1000W Ver. 1.3 3 7 63 1515 0 Procedure: [RF Level Check] 1. Terminate the COMPONENT VIDEO OUT (Y) connector in Connection: 75 Ω. 2. Connect an oscilloscope across 75 Ω terminator. oscilloscope 3. Turn the power on. DMB10 board 4.
  • Page 28: Diagrams

    HCD-FX999W/FX1000W Ver. 1.2 SECTION 7 3 7 63 1515 0 DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) For Schematic Diagrams. For Printed Wiring Boards.
  • Page 29 HCD-FX999W/FX1000W Ver. 1.1 3 7 6 3 1 5 1 5 0 MEMO • Circuit Boards Location MIB01 POWER board I/O board (HCD-FX1000W only) MIB01 board (HCD-FX1000W only) MAIN board DMB10 board KEY board TX board LED board MIC board...
  • Page 30: Block Diagram - Rf Section

    HCD-FX999W/FX1000W Ver. 1.1 7-1. BLOCK DIAGRAM – RF SECTION – 3 7 6 3 1 5 1 5 0 FX999W RFMON VIDEO SECTION V2REFD CB/B for TEST CB/R FX1000W DVDRFIP YUV0 YUV0 YUV1 YUV1 YUV2 YUV2 DVDA YUV3 DVDB...
  • Page 31: Block Diagram - Mib Section

    HCD-FX999W/FX1000W Ver. 1.1 7-2. BLOCK DIAGRAM – MIB SECTION – 3 7 6 3 1 5 1 5 0 FX1000W • Signal Pash PO2 - PO9 : VIDEO 53-55, 58-62 S(2) - S(9) : CHROMA 33 RESET8 : COMPONENT VIDEO...
  • Page 32: Block Diagram - Video Section

    HCD-FX999W/FX1000W Ver. 1.1 7-3. BLOCK DIAGRAM – VIDEO SECTION – 3 7 6 3 1 5 1 5 0 J601(1/2) VIDEO VIDEO IN VIDEO IN IC201 IC204 VIDEO AMP, 75Ω DRIVER VIDEO SWITCH 14 2B 6 YIN OUT2 YOUT...
  • Page 33: Block Diagram - Amp Section

    HCD-FX999W/FX1000W 7-4. BLOCK DIAGRAM – AMP SECTION – 3 7 6 3 1 5 1 5 0 ALRCK ABCK ASDATA0 ASDATA1 SECTION ASDATA2 IC506 ACLK IC507 DIGITAL AUDIO SD-RAM PROCESSOR 7-10 72-75 J603 13-16 77-80 18-21 D0-D15 98,99 D0 – D15...
  • Page 34: Block Diagram - Audio Section

    HCD-FX999W/FX1000W 7-5. BLOCK DIAGRAM – AUDIO SECTION – 3 7 6 3 1 5 1 5 0 IC301 IC108 HEADPHONE STREAM PROCESSOR J801 HPOUTL1 PHONES HPOUTL2 Q507 HPOUTR1 Q806 - 809 MUTING MUTING HPOUTR2 CONTROL IC101 SPEAKER POWER DRIVER D1 –...
  • Page 35: Block Diagram - Main Section

    HCD-FX999W/FX1000W 7-6. BLOCK DIAGRAM – MAIN SECTION – 3 7 6 3 1 5 1 5 0 IC721 STOCKER MOTOR DRIVE OUT1 M761 (STOCKER) OUT2 IC711 ROLLER MOTOR DRIVE OUT1 M781 OUT2 (ROLLER) IC701 MODE MOTOR DRIVE OUT1 DC/DC...
  • Page 36: Block Diagram - Diat Transmit Section

    HCD-FX999W/FX1000W 7-7. BLOCK DIAGRAM – DIAT TRANSMIT SECTION – 3 7 6 3 1 5 1 5 0 VCC(9V) IC801 IC800 +12V +2.5V +2.5V REG IC804 RF MODULATOR IC802 D/A CONVERTER LEVEL SHIFT 49 LRCK LRCKO 50 BCK BCKO...
  • Page 37: Printed Wiring Board - Changer Section

    HCD-FX999W/FX1000W Ver. 1.1 • See page 29 for Circuit Boards Location. 7-8. PRINTED WIRING BOARD – CHANGER SECTION – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 SW(1) BOARD MAIN BOARD RELAY BOARD CN502 • Semiconductor...
  • Page 38: Schematic Diagram - Changer Section

    HCD-FX999W/FX1000W Ver. 1.1 • See page 76 for IC Block Diagrams. 7-9. SCHEMATIC DIAGRAM – CHANGER SECTION – 3 7 6 3 1 5 1 5 0 RELAY BOARD CN751 CN702 R731 DIODE DIODE I C 7 5 1...
  • Page 39: Printed Wiring Board - Dmb10 Section (Side A)

    HCD-FX999W/FX1000W Ver. 1.1 • See page 29 for Circuit Boards Location. 7-10. PRINTED WIRING BOARD – DMB10 SECTION (SIDE A) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 IC103 (EEP ROM) can not be replaced individually.
  • Page 40: Printed Wiring Board - Dmb10 Section (Side B)

    HCD-FX999W/FX1000W Ver. 1.1 • See page 29 for Circuit Boards Location. 7-11. PRINTED WIRING BOARD – DMB10 SECTION (SIDE B) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 • Semiconductor Location Ref. No. Location...
  • Page 41: Schematic Diagram - Dmb10 Section (1/4)

    HCD-FX999W/FX1000W Ver. 1.1 7-12. SCHEMATIC DIAGRAM – DMB10 SECTION (1/4) – 3 7 6 3 1 5 1 5 0 FL401 CN401 FB402 FB404 MAIN JL4601 JL4602 BOARD (2/8) FL403 JL4603 JL4604 FB403 FB406 CNP506 JL4605 JL4606 SUFFIX-14 Page 48...
  • Page 42: Schematic Diagram - Dmb10 Section (2/4)

    HCD-FX999W/FX1000W Ver. 1.1 • See page 82 for IC Pin Function Description. • See page 70 for Waveforms. 7-13. SCHEMATIC DIAGRAM – DMB10 SECTION (2/4) – 3 7 6 3 1 5 1 5 0 FX999W FX999W CN301 JL4701...
  • Page 43: Schematic Diagram - Dmb10 Section (3/4)

    HCD-FX999W/FX1000W Ver. 1.2 7-14. SCHEMATIC DIAGRAM – DMB10 SECTION (3/4) – 3 7 6 3 1 5 1 5 0 IC103 (EEP ROM) can not be replaced individually. Replace it with DMB10 board assembly for service. (Page 42) (Page 42)
  • Page 44: Schematic Diagram - Dmb10 Section (4/4)

    HCD-FX999W/FX1000W 7-15. SCHEMATIC DIAGRAM – DMB10 SECTION (4/4) – 3 7 6 3 1 5 1 5 0 (Page 42) (Page 41, R225 R223 100k 100k R232 R234 R231 R221 C211 0.033 C209 R230 C233 0.033 0.0047 C212 R233 C215 0.01...
  • Page 45: Printed Wiring Board - Main Section (Side A)

    HCD-FX999W/FX1000W • See page 29 for Circuit Boards Location. 7-16. PRINTED WIRING BOARD – MAIN SECTION (SIDE A) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 refer to SUPPLEMENT-1 about FX999W : E13 and FX1000W •...
  • Page 46: Printed Wiring Board - Main Section (Side B)

    HCD-FX999W/FX1000W • See page 29 for Circuit Boards Location. 7-17. PRINTED WIRING BOARD – MAIN SECTION (SIDE B) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 refer to SUPPLEMENT-1 about FX999W : E13 and FX1000W...
  • Page 47: Schematic Diagram - Main Section (1/8)

    HCD-FX999W/FX1000W • See page 79 for IC Pin Function Description. • See page 70 for Waveform. 7-18. SCHEMATIC DIAGRAM – MAIN SECTION (1/8) – 3 7 6 3 1 5 1 5 0 refer to SUPPLEMENT-1 about FX999W : E13 and FX1000W CN509 FFC-S-1.0...
  • Page 48: Schematic Diagram - Main Section (2/8)

    HCD-FX999W/FX1000W 7-19. SCHEMATIC DIAGRAM – MAIN SECTION (2/8) – 3 7 6 3 1 5 1 5 0 MAIN refer to SUPPLEMENT-1 about FX999W : E13 and FX1000W BOARD (1/8) (Page 47) IC515 ( 2 / 8 ) IC TA7809LS...
  • Page 49: Schematic Diagram - Main Section (3/8)

    HCD-FX999W/FX1000W • See page 72 for IC Block Diagrams. 7-20. SCHEMATIC DIAGRAM – MAIN SECTION (3/8) – 3 7 6 3 1 5 1 5 0 refer to SUPPLEMENT-1 about FX999W : E13 and FX1000W ( 3 / 8 )
  • Page 50: Schematic Diagram - Main Section (4/8)

    HCD-FX999W/FX1000W • See page 72 for IC Block Diagrams. 7-21. SCHEMATIC DIAGRAM – MAIN SECTION (4/8) – 3 7 6 3 1 5 1 5 0 refer to SUPPLEMENT-1 about FX999W : E13 and FX1000W ( 4 / 8 )
  • Page 51: Schematic Diagram - Main Section (5/8)

    HCD-FX999W/FX1000W • See page 72 for IC Block Diagram. • See page 70 for Waveform. 7-22. SCHEMATIC DIAGRAM – MAIN SECTION (5/8) – 3 7 6 3 1 5 1 5 0 refer to SUPPLEMENT-1 about FX999W : E13 and FX1000W...
  • Page 52: Schematic Diagram - Main Section (6/8)

    HCD-FX999W/FX1000W • See page 72 for IC Block Diagrams. 7-23. SCHEMATIC DIAGRAM – MAIN SECTION (6/8) – 3 7 6 3 1 5 1 5 0 MAIN BOARD refer to SUPPLEMENT-1 about FX999W : E13 and FX1000W (4/8) (Page 50)
  • Page 53: Schematic Diagram - Main Section (7/8)

    HCD-FX999W/FX1000W 7-24. SCHEMATIC DIAGRAM – MAIN SECTION (7/8) – 3 7 6 3 1 5 1 5 0 refer to SUPPLEMENT-1 about FX999W : E13 and FX1000W TX BOARD CN902 CN802 ( 7 / 8 ) (Page 69) L946...
  • Page 54: Schematic Diagram - Main Section (8/8)

    HCD-FX999W/FX1000W • See page 71, 73 for IC Block Diagrams. • See page 70 for Waveform. • See page 77 for IC Pin Function Description. 7-25. SCHEMATIC DIAGRAM – MAIN SECTION (8/8) – 3 7 6 3 1 5 1 5 0...
  • Page 55: Printed Wiring Board - Fl/Key Section

    HCD-FX999W/FX1000W Ver. 1.1 • See page 29 for Circuit Boards Location. 7-26. PRINTED WIRING BOARD – FL/KEY SECTION – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 • Semiconductor Location Ref. No. Location D801 D802...
  • Page 56: Schematic Diagram - Fl/Key Section

    HCD-FX999W/FX1000W Ver. 1.1 • See page 73, 74 for IC Block Diagrams. 7-27. SCHEMATIC DIAGRAM – FL/KEY SECTION – 3 7 6 3 1 5 1 5 0 R852 R855 R857 R858 R851 R853 R856 2.2k 2.2k 4.7k 2.2k 4.7k...
  • Page 57: Printed Wiring Board - Led / Mic Section

    HCD-FX999W/FX1000W Ver. 1.1 • See page 29 for Circuit Boards Location. 7-28. PRINTED WIRING BOARD – LED / MIC SECTION – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 MAIN BOARD CN309 SUFFIX-14 Page 46 •...
  • Page 58: Schematic Diagram - Led / Mic Ssection

    HCD-FX999W/FX1000W Ver. 1.1 7-29. SCHEMATIC DIAGRAM – LED / MIC SECTION – 3 7 6 3 1 5 1 5 0 R833 TP843 R834 R835 R836 R837 R838 R839 TP841 2.2k 2.2k 4.7k CN803 S810 S815 S816 S809 S811...
  • Page 59: Printed Wiring Board - I/O Section (Side A)

    HCD-FX999W/FX1000W • See page 29 for Circuit Boards Location. 7-30. PRINTED WIRING BOARD – I/O SECTION (SIDE A) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 • Semiconductor Location Ref. No. Location IC201 IC203...
  • Page 60: Printed Wiring Board - I/O Section (Side B)

    HCD-FX999W/FX1000W Ver. 1.1 • See page 29 for Circuit Boards Location. 7-31. PRINTED WIRING BOARD – I/O SECTION (SIDE B) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 AUDIO IN MONITOR VIDEO IN COMPONENT...
  • Page 61: Schematic Diagram - I/O Section

    HCD-FX999W/FX1000W Ver. 1.1 • See page 74 for IC Block Diagrams. • See page 70 for Waveform. 7-32. SCHEMATIC DIAGRAM – I/O SECTION – 3 7 6 3 1 5 1 5 0 CN602 TP634 R640 L603 TP635 TP636...
  • Page 62: Printed Wiring Board - Mib01 Section (Side A)

    HCD-FX999W/FX1000W Ver. 1.1 • See page 29 for Circuit Boards Location. 7-33. PRINTED WIRING BOARD – MIB01 SECTION (SIDE A) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 FX1000W HD MI CN601 (DVD ONLY) •...
  • Page 63: Printed Wiring Board - Mib01 Section (Side B)

    HCD-FX999W/FX1000W Ver. 1.1 • See page 29 for Circuit Boards Location. 7-34. PRINTED WIRING BOARD – MIB01 SECTION (SIDE B) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 FX1000W • Semiconductor Location IC607 Ref. No.
  • Page 64: Schematic Diagram - Mib01 Section (1/3)

    HCD-FX999W/FX1000W Ver. 1.1 • See page 87 for IC Pin Function Description. 7-35. SCHEMATIC DIAGRAM – MIB01 SECTION (1/3) – 3 7 6 3 1 5 1 5 0 FX1000W IC509 HY57V161610ETP-7 CL502 C516 0.01 R5452 4.7k C520 C512...
  • Page 65: Schematic Diagram - Mib01 Section (2/3)

    HCD-FX999W/FX1000W Ver. 1.1 • See page 76for IC Block Diagrams. • See page 90 for IC Pin Function Description. 7-36. SCHEMATIC DIAGRAM – MIB01 SECTION (2/3) – 3 7 6 3 1 5 1 5 0 FX1000W C543 0.033...
  • Page 66: Schematic Diagram - Mib01 Section (3/3)

    HCD-FX999W/FX1000W Ver. 1.1 • See page 70 for Waveform. 7-37. SCHEMATIC DIAGRAM – MIB01 SECTION (3/3) – 3 7 6 3 1 5 1 5 0 FX1000W R696 C627 0.01 C620 0.01 R612 R664 C611 0.01 R690 C607 0.01...
  • Page 67: Printed Wiring Board - Mib01 Power Section

    HCD-FX999W/FX1000W Ver. 1.1 • See page 29 for Circuit Boards Location. 7-38. PRINTED WIRING BOARD – MIB01 POWER SECTION – 7-39. SCHEMATIC DIAGRAM – MIB01 POWER SECTION – 3 7 6 3 1 5 1 5 0 :Uses unleaded solder.
  • Page 68: Printed Wiring Board - Tx Section

    HCD-FX999W/FX1000W Ver. 1.1 • See page 29 for Circuit Boards Location. 7-40. PRINTED WIRING BOARD – TX SECTION – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 I/O BOARD CN603 (Page 60) (CHASSIS) CN803 IC804...
  • Page 69: Schematic Diagram - Tx Section

    HCD-FX999W/FX1000W Ver. 1.1 • See page 75 for IC Block Diagrams. • See page 70 for Waveform. 7-41. SCHEMATIC DIAGRAM – TX SECTION – 3 7 6 3 1 5 1 5 0 IC B/D IC800 CN802 TA7809LS TP803...
  • Page 70 HCD-FX999W/FX1000W Ver. 1.1 • Waveforms 3 7 6 3 1 5 1 5 0 – DMB10 Board – – MAIN Board – – I/O Board – – TX Board – IC804 tl (OSCO) IC102 6 (DVDRFIP) IC102 <x// (YUV4)
  • Page 71 HCD-FX999W/FX1000W 3 7 63 1515 0 • IC Block Diagrams – MAIN Board – IC505 LC89056W-E AUDIO C BIT PA/PB DETECT DETECT EMPHA SAMPLING FREQUENCY MICROCOMPUTER INTERFACE XSEL LOCK XOUT CLOCK DETECT XMCK 19 DVDD MODE0 MODE 18 DGND...
  • Page 72 HCD-FX999W/FX1000W 3 7 63 1515 0 IC101,102,105,106,107 CXD9775M GVDD B GVDD GVDD B BST B DVDD DREG DREG GND 1 PVDD B GATE PWM BP 2 PVDD B RECEIVER DRIVE OUT B TIMING GND 3 OUT B CONTROL DGND &...
  • Page 73 HCD-FX999W/FX1000W 3 7 63 1515 0 IC514 SN74LV157APWR STROEE SELECT – FL Board – IC803 ML9208-03MBZ03B 64 VDD 63 DA 8 BIT SHIFT 62 CP REGISTER 61 CS L 13942296513 60 RESET COMMAND PORT DECODER DRIVER CONTROL CIRCUIT DRIVER ADRAM ×...
  • Page 74 HCD-FX999W/FX1000W 3 7 63 1515 0 IC802 BU2099FV 12BIT SHIFT REGESTER 12BIT STORAGE RAGESTER OUTPUT BUFFER (Open Drain) – I/O Board – IC203 NJM2235V (TE2) IC601 MC14052BDR2 IN 1 BUFFER SW 1 IN 2 BIAS SW 2 L 13942296513...
  • Page 75 HCD-FX999W/FX1000W 3 7 63 1515 0 – TX Board – IC801 TK11225CMCL-G CONTROL CIRCUIT CONSTANT OVER HEAT & CURRENT OVER CURRENT SOURCE PROTECT BANDGAP REFERENCE IC804 CXD4016R L 13942296513 48 47 46 45 44 41 40 39 38 37 36...
  • Page 76 HCD-FX999W/FX1000W Ver. 1.1 3 7 63 1515 0 – RELAY Board – IC701, 711, 721 BA6956AN IC701, 711, 721 BA6956AN CONTROL LOGIC – MIB01 Board – IC506 ADV7300AKST 48 S_BLANK 47 RSET1 TIMING DEMUX 46 VREF GENERATOR 45 COMP1...
  • Page 77 HCD-FX999W/FX1000W 3 7 63 1515 0 • IC Pin Function Description MAIN BOARD IC506 CXD9862R (DIGITAL AUDIO PROCESSOR) Pin No. Pin Name Description — Ground terminal XRST System reset signal input from the system controller “L”: reset EXTIN Master clock signal input terminal (connected to ground)
  • Page 78 HCD-FX999W/FX1000W 3 7 63 1515 0 Pin No. Pin Name Description WMD0 External memory wait mode setting terminal (connected to +3.3V) PAGE2 External memory page selection signal output terminal (not used) — Ground terminal 52, 53 PAGE1, PAGE0 External memory page selection signal output terminal (not used)
  • Page 79 HCD-FX999W/FX1000W 3 7 63 1515 0 MAIN BOARD IC509 M30622MGP-A14FPU0 (SYSTEM CONTROLLER) Pin No. Pin Name Description DAMP SCDT/ Digital amp (IC108, 110) data output DIAT_SDATA DAMP SHIFT/ Digital amp (IC108, 110) data output DIAT_SCLK XSCEN Voltage control for amp...
  • Page 80 HCD-FX999W/FX1000W 3 7 63 1515 0 Pin No. Pin Name Description DRIVE_RST(EN) Driver signal reset DRIVE_OCP(DIAG) Digital amp (power driver) diag OVERFLOW1 Over flow status1 of digital amp (IC110) OVERFLOW2 Over flow status2 of digital amp (IC108 to 110)
  • Page 81 HCD-FX999W/FX1000W 3 7 63 1515 0 Pin No. Pin Name Description — Ground KEY0 Key input 0 VREF Reference Voltage (+3.3V) Power supply (+3.3V) M-ST/WMUTE WMUTE signal output L 13942296513 u163 http://www.xiaoyu163.com...
  • Page 82 HCD-FX999W/FX1000W 3 7 63 1515 0 DMB10 BOARD IC102 CXD9804R (CD/DVD RF AMP, FOCUS/TRACKING ERR AMP, DVD SYSTEM PROCESSOR, DIGITAL SERVO PROCESSOR) Pin No. Pin Name Description AGND — Terminal Ground DVDA AC coupled input path A DVDB AC coupled input path B...
  • Page 83 HCD-FX999W/FX1000W 3 7 63 1515 0 Pin No. Pin Name Description Connected to +3.3V Connected to +3.3V Connected to +3.3V MAMUTE MAMUTE signal output to System Controller (IC509)(not used) DVDD18 — Power Supply (+1.8V) 53 to 58 IOA 2 to 7...
  • Page 84 HCD-FX999W/FX1000W 3 7 63 1515 0 Pin No. Pin Name Description DQMO DQM0 signal output to SD-RAM (IC104) MREQ MREQ signal input Data bus 7 from SD-RAM (IC104) DVSS — Terminal Ground 117, 118 RD 6, 5 Data bus 6, 5 from SD-RAM (IC104) DVSS —...
  • Page 85 HCD-FX999W/FX1000W 3 7 63 1515 0 Pin No. Pin Name Description LIMSW LIMSW signal output to Optical pick-up OCSW SEN signal input from System Controller (IC509) (not used) VCLK System clock output CKSW — Not Used Reset signal output to VIDEO DAC...
  • Page 86 HCD-FX999W/FX1000W 3 7 63 1515 0 Pin No. Pin Name Description SDPIF SPDIF output RFGND18 — Terminal Ground RFVDD18 — Power Supply (+1.8V) ZTALO Oscillator output signal ZTALI Oscillator input signal JITFO RF jitter meter output JITFN Negative input of operation amplifier for RF jigger meter PLLVSS —...
  • Page 87 HCD-FX999W/FX1000W 3 7 63 1515 0 MIB01 BOARD IC503 CXD9837R (PROGRESSIVE SCAN CONVERTER) Pin No. Pin Name Desciption OVDD — Positive supply voltage (+3.3V) for Pad Ring CLKI System clock input (27MHz) TEST7 Test purpose only (must be connected to ground)
  • Page 88 HCD-FX999W/FX1000W 3 7 63 1515 0 Pin No. Pin Name Desciption OVSS — Digital ground for Pad Ring Address output port for SDRAM Address output port for SDRAM Address output port for SDRAM Address output port for SDRAM OVSS —...
  • Page 89 HCD-FX999W/FX1000W 3 7 63 1515 0 Pin No. Pin Name Desciption RFFO MPEG flag output port (not used) Data input/output of MPU interface Clock inputt of MPU interface System reset input (negative) OVSS — Digital ground for Pad Ring CVDD —...
  • Page 90 HCD-FX999W/FX1000W Ver. 1.1 3 7 63 1515 0 MIB01 BOARD IC507 CXD9836R (PIXEL RESOLUTION CONVERTER) Pin No. Pin Name Desciption — Digital ground XTCK1 Test purpose only (must be connected to ground) Test purpose only (must be connected to +3.3V) XTST Test purpose only (must be connected to +3.3V)
  • Page 91 HCD-FX999W/FX1000W Ver. 1.1 3 7 63 1515 0 Pin No. Pin Name Desciption — Digital ground OVDDE2 — Digital positive supply voltage (+3.3V) for Pad Ring 93 to 95 QR7 to QR9 R data output Vertical sync output Horizontal sync output...
  • Page 92: Exploded Views

    HCD-FX999W/FX1000W Ver. 1.2 SECTION 8 3 7 63 1515 0 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • Abbreviation The components identified by mark 0 or may have some difference from the original : Australian model dotted line with mark 0 are critical for safety.
  • Page 93: Front Panel Assy Section

    HCD-FX999W/FX1000W Ver. 1.2 3 7 63 1515 0 8-2. FRONT PANEL ASSY SECTION supplied supplied supplied not supplied L 13942296513 supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 2-585-417-51 WINDOW (FL) X-2050-544-1 PLAY BUTTON SUB ASSY...
  • Page 94: Chassis Section-1

    HCD-FX999W/FX1000W Ver. 1.2 3 7 63 1515 0 8-3. CHASSIS SECTION-1 not supplied not supplied chassis section-2 L 13942296513 not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1074-641-A TUNER UNIT (DTP-005 SP) 0 106...
  • Page 95: Chassis Section-2

    HCD-FX999W/FX1000W New part of EEPROM (IC103) on the DMB10 board cannot be used. Ver. 1.4 Therefore, if the mounted DMB10 board (A-1111-270-A, etc. ) is replaced, exchange new EEPROM (IC103) with that used before the replacement. 3 7 63 1515 0 8-4.
  • Page 96: Dvd Mechanism Deck Section-1 (Cdm69Eh-Dvbu101)

    HCD-FX999W/FX1000W 3 7 63 1515 0 8-5. DVD MECHANISM DECK SECTION-1 (CDM69EH-DVBU101) S702 M761 L 13942296513 DVD mechanism deck section-2 not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-686-725-13 STOCKER MOTOR BOARD 4-239-699-01 PULLEY 3-087-053-01 +BVTP2.6 (3CR)
  • Page 97: Dvd Mechanism Deck Section-2 (Cdm69Eh-Dvbu101)

    HCD-FX999W/FX1000W 3 7 63 1515 0 8-6. DVD MECHANISM DECK SECTION-2 (CDM69EH-DVBU101) DVD mechanism deck section-3 DVD mechanism deck section-4 L 13942296513 optical pick-up section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-686-727-13 SW (1) BOARD 3-087-053-01 +BVTP2.6 (3CR)
  • Page 98: Dvd Mechanism Deck Section-3 (Cdm69Eh-Dvbu101)

    HCD-FX999W/FX1000W 3 7 63 1515 0 8-7. DVD MECHANISM DECK SECTION-3 (CDM69EH-DVBU101) not supplied supplied not supplied supplied supplied L 13942296513 not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-240-040-01 SPRING (DISC STOPPER), TORSION 4-240-039-01 LEVER (DISC STOPPER) 4-992-069-01 SCREW (+PTPWH) (M2) (DIA.
  • Page 99: Dvd Mechanism Deck Section-4 (Cdm69Eh-Dvbu101)

    HCD-FX999W/FX1000W 3 7 63 1515 0 8-8. DVD MECHANISM DECK SECTION-4 (CDM69EH-DVBU101) supplied L 13942296513 M781 DVD mechanism deck section-5 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-4954-626-1 LEVER (ROLLER) ASSY 4-240-041-01 SPRING (SLIDER 2), TENSION 4-239-666-01 GEAR 3-087-053-01 +BVTP2.6 (3CR)
  • Page 100: Dvd Mechanism Deck Section-5 (Cdm69Eh-Dvbu101)

    HCD-FX999W/FX1000W 3 7 63 1515 0 8-9. DVD MECHANISM DECK SECTION-5 (CDM69EH-DVBU101) L 13942296513 DVD mechanism deck section-6 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-240-020-01 GEAR (TIMING) 4-239-699-01 PULLEY 4-239-708-02 BELT (FRONT), TIMING...
  • Page 101: Dvd Mechanism Deck Section-6 (Cdm69Eh-Dvbu101)

    HCD-FX999W/FX1000W 3 7 63 1515 0 8-10. DVD MECHANISM DECK SECTION-6 (CDM69EH-DVBU101) M771 not supplied L 13942296513 supplied S771 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-239-693-02 CAM (GEAR) 4-239-694-01 GEAR (MODE CAM) 1-686-723-13 SENSOR BOARD...
  • Page 102: Optical Pick-Up Section (Khm-310Cab)

    HCD-FX999W/FX1000W 3 7 63 1515 0 8-11. OPTICAL PICK-UP SECTION (KHM-310CAB) L 13942296513 not supplied Ref. No. Part No. Description Remark 0 601 8-820-291-02 OPTICAL PICK-UP (KHM-310CAB/C2RP) 3-087-599-01 INSULATOR SCREW 3-088-372-01 INSULATOR u163 http://www.xiaoyu163.com...
  • Page 103: Electrical Parts List

    HCD-FX999W/FX1000W Ver. 1.3 SECTION 9 DMB10 3 7 63 1515 0 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • RESISTORS When indicating parts by reference number, parts list may be different from the parts All resistors are in ohms.
  • Page 104 HCD-FX999W/FX1000W Ver. 1.2 DMB10 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C189 1-128-934-91 CERAMIC CHIP 0.33uF FB114 1-414-226-21 INDUCTOR, FERRITE BEAD C190 1-126-205-11 ELECT CHIP 47uF 6.3V FB115 1-414-226-21 INDUCTOR, FERRITE BEAD...
  • Page 105 HCD-FX999W/FX1000W Ver. 1.1 DMB10 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R221 1-218-889-11 METAL CHIP 0.5% 1/10W R113 1-211-977-11 METAL CHIP 0.5% 1/10W R223 1-218-895-11 METAL CHIP 100K 0.5%...
  • Page 106 HCD-FX999W/FX1000W Ver. 1.1 DMB10 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < VIBRATOR > R1522 1-216-864-11 SHORT CHIP 0 (FX1000W) R1523 1-216-864-11 SHORT CHIP 0 (FX1000W) X101 1-781-867-21 VIBRATOR, CRYSTAL (27MHz)
  • Page 107 HCD-FX999W/FX1000W Ver. 1.1 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D802 6-501-193-01 DIODE 1SS355WTE-17 C103 1-104-662-91 ELECT 22uF D803 8-719-069-56 DIODE UDZSTE-176.2B (FX999W) D804 6-501-193-01 DIODE 1SS355WTE-17 C103 1-124-234-00 ELECT...
  • Page 108 HCD-FX999W/FX1000W Ver. 1.1 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C242 1-500-284-21 INDUCTOR, FERRITE BEAD (FX999W) CN201 1-779-281-11 CONNECTOR, FFC (LIF (NON-ZIF)) 13P C601 1-126-933-11 ELECT 100uF CN601 1-779-291-11 CONNECTOR, FFC (LIF (NON-ZIF)) 23P...
  • Page 109 HCD-FX999W/FX1000W 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R230 1-218-285-11 METAL CHIP 1/10W KEY BOARD R231 1-218-285-11 METAL CHIP 1/10W ********* R232 1-218-285-11 METAL CHIP 1/10W < RESISTOR >...
  • Page 110 HCD-FX999W/FX1000W Ver. 1.2 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark S812 1-786-763-11 SWITCH, TACTILE (DISC4) C182 1-115-185-11 CERAMIC CHIP 0.033uF S813 1-786-763-11 SWITCH, TACTILE (DISC3) C185 1-115-185-11 CERAMIC CHIP 0.033uF...
  • Page 111 HCD-FX999W/FX1000W MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C290 1-162-966-11 CERAMIC CHIP 0.0022uF 10% C402 1-162-927-11 CERAMIC CHIP 100PF C403 1-162-927-11 CERAMIC CHIP 100PF C291 1-162-966-11 CERAMIC CHIP 0.0022uF 10%...
  • Page 112 HCD-FX999W/FX1000W MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C570 1-107-826-11 CERAMIC CHIP 0.1uF 0 C912 1-117-693-11 CERAMIC 100PF 250V (EXCEPT FX999W:MX) C571 1-107-826-11 CERAMIC CHIP 0.1uF 0 C912 1-113-907-51 CERAMIC 0.0022uF 20%...
  • Page 113 HCD-FX999W/FX1000W MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * CN309 1-568-954-11 PIN, CONNECTOR 5P EB905 1-537-770-21 TERMINAL BOARD, GROUND CN502 1-784-384-11 CONNECTOR, FFC/FPC 27P CN504 1-784-370-21 CONNECTOR, FFC/FPC 11P...
  • Page 114 HCD-FX999W/FX1000W MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < TERMINAL BOARD > Q112 8-729-600-22 TRANSISTOR 2SA1235-F Q301 8-729-120-28 TRANSISTOR 2SC1623-L5L6 J202 1-780-203-11 TERMINAL BOARD (SP) (2P) (SPEAKER) Q302...
  • Page 115 HCD-FX999W/FX1000W MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R205 1-220-942-11 METAL CHIP 1/4W R345 1-216-833-11 METAL CHIP 1/10W R346 1-216-817-11 METAL CHIP 1/10W R206 1-220-942-11 METAL CHIP 1/4W...
  • Page 116 HCD-FX999W/FX1000W MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R475 1-216-864-11 SHORT CHIP R553 1-216-809-11 METAL CHIP 1/10W R554 1-216-809-11 METAL CHIP 1/10W R478 1-216-864-11 SHORT CHIP R555 1-216-830-11 METAL CHIP 5.6K...
  • Page 117 HCD-FX999W/FX1000W MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R612 1-216-833-11 METAL CHIP 1/10W R700 1-216-809-11 METAL CHIP 1/10W R613 1-216-864-11 SHORT CHIP R701 1-216-809-11 METAL CHIP 1/10W R614...
  • Page 118 HCD-FX999W/FX1000W Ver. 1.4 MAIN MIB01 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 0 R903 1-215-929-11 METAL OXIDE 100K R955 1-216-817-11 METAL CHIP 1/10W (EXCEPT FX999W:MX) 0 R904 1-215-926-00 METAL OXIDE...
  • Page 119 HCD-FX999W/FX1000W Ver. 1.1 MIB01 3 7 63 1515 0 Ref. No. Ref. No. Part No. Part No. Description Description Remark Remark Ref. No. Part No. Description Remark C517 1-162-970-11 CERAMIC CHIP 0.01uF C613 1-162-970-11 CERAMIC CHIP 0.01uF C518 1-107-826-11 CERAMIC CHIP 0.1uF...
  • Page 120 HCD-FX999W/FX1000W Ver. 1.1 MIB01 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < IC > R612 1-216-864-11 SHORT CHIP R615 1-216-821-11 METAL CHIP 1/10W IC111 6-550-008-01 TRANSISTOR UM6K1N-TN R617 1-216-821-11 METAL CHIP...
  • Page 121 HCD-FX999W/FX1000W Ver. 1.1 MIB01 MIB01 POWER 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R5547 1-216-864-11 SHORT CHIP R5102 1-216-833-11 METAL CHIP 1/10W R5548 1-216-864-11 SHORT CHIP R5202 1-216-864-11 SHORT CHIP...
  • Page 122 HCD-FX999W/FX1000W Ver. 1.1 MIB01 POWER MODE MOTOR RELAY 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark TK9002 1-537-770-21 TERMINAL BOARD, GROUND < TRANSISTOR > ************************************************************ Q807 6-550-889-01 TRANSISTOR 2SC5938-T112-1B MIC BOARD...
  • Page 123 HCD-FX999W/FX1000W RELAY ROLLER MOTOR SENSOR ST ENCODER 3 7 63 1515 0 STOCKER MOTOR SW (1) SW (2) SW (3) SW (4) Ref. No. Ref. No. Part No. Part No. Description Description Remark Remark Ref. No. Part No. Description Remark <...
  • Page 124 HCD-FX999W/FX1000W 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C834 1-107-826-11 CERAMIC CHIP 0.1uF L812 1-456-509-11 INDUCTOR 10uH C835 1-162-966-11 CERAMIC CHIP 0.0022uF 10% C836 1-164-156-11 CERAMIC CHIP 0.1uF < TRANSISTOR >...
  • Page 125 HCD-FX999W/FX1000W Ver. 1.2 3 7 63 1515 0 Ref. No. Part No. Description Remark MISCELLANEOUS ************** 1-828-336-11 WIRE (FLAT TYPE) (15 CORE) 1-828-952-11 WIRE (FLAT TYPE) (9 CORE) 1-787-331-11 FAN, D.C. 0 106 1-696-847-22 CORD, POWER (FX999W:AUS) 0 106...
  • Page 126 HCD-FX999W/FX1000W 3 7 63 1515 0 MEMO L 13942296513 u163 http://www.xiaoyu163.com...
  • Page 127 SERVICE MANUAL HCD-FX999W Ver. 1.2 2005.10 SUPPLEMENT-1 Subject: MAIN board changed to suffix-15 from suffix-14 * HCD-FX999W : E13 model (220-230V AC area in E model), Taiwan model and HCD-FX1000W used suffix-15 of MAIN board. L 13942296513 u163 9-879-743-81 http://www.xiaoyu163.com...
  • Page 128 HCD-FX999W/FX1000W 3 7 63 1515 0 Part number of printed wiring board changed to suffix-15 from suffix-14. It has any difference between suffix-14 and suffix-15. This supplement-1 describes the difference in the two boards. Refer to original service manual (9-879-743-0[]) for other information.
  • Page 129 HCD-FX999W/FX1000W Ver. 1.2 PRINTED WIRING BOARD – MAIN SECTION (SIDE A) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 • Semiconductor Location Ref. No. Location D503 D914 D915 D923 D925 D932 IC101 IC102 IC105...
  • Page 130 HCD-FX999W/FX1000W Ver. 1.2 PRINTED WIRING BOARD – MAIN SECTION (SIDE B) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 SPEAKER FRONT:ONLY FOR SS-TS47 CENTER:ONLY FOR SS-CT46 WOOFER:ONLY FOR SS-WS 43 • Semiconductor Location FRONT R...
  • Page 131 HCD-FX999W/FX1000W Ver. 1.2 SCHEMATIC DIAGRAM – MAIN SECTION (1/8) – 3 7 6 3 1 5 1 5 0 CN509 FFC-S-1.0 ( 1 / 8 ) SKIP DSP_SKIP DSP_DO DSP_DO DSP_DIN DSP_BST DSP_BST DSP_GP9 DSP_PM DSP_PM DSP_ACK DSP_XRST DSP_XRST...
  • Page 132 HCD-FX999W/FX1000W SCHEMATIC DIAGRAM – MAIN SECTION (2/8) – 3 7 6 3 1 5 1 5 0 MAIN BOARD SUPPLEMENT-1 (1/8) Page 5 ( 2 / 8 ) IC515 IC TA7809LS TP517 C595 C596 C597 R704 0.33 47 35V...
  • Page 133 HCD-FX999W/FX1000W SCHEMATIC DIAGRAM – MAIN SECTION (3/8) – 3 7 6 3 1 5 1 5 0 ( 3 / 8 ) R345 R468 R347 R469 EB910 TERMINAL BOARD TP331 R317 R316 EB907 TERMINAL BOARD R319 TP334 C324 25V F...
  • Page 134 HCD-FX999W/FX1000W SCHEMATIC DIAGRAM – MAIN SECTION (4/8) – 3 7 6 3 1 5 1 5 0 ( 4 / 8 ) R384 R480 R383 C137 IC106 R120 R128 25V F EXCEPT E32: CXD9775M C116 1 16V F E32: CXD9774M...
  • Page 135 HCD-FX999W/FX1000W SCHEMATIC DIAGRAM – MAIN SECTION (5/8) – 3 7 6 3 1 5 1 5 0 MAIN BOARD (3/8) SUPPLEMENT-1 Page 7 ( 5 / 8 ) L107 10uH Q303 2SC3243-TP-E CN300 C108 C307 MAIN BOARD (4/8) R428...
  • Page 136 HCD-FX999W/FX1000W SCHEMATIC DIAGRAM – MAIN SECTION (6/8) – 3 7 6 3 1 5 1 5 0 MAIN BOARD SUPPLEMENT-1 Page 8 (4/8) ( 6 / 8 ) C110 0.001 MAIN BOARD (3/8) SUPPLEMENT-1 Page 7 TP383 TP382 J203...
  • Page 137 HCD-FX999W/FX1000W Ver. 1.2 SCHEMATIC DIAGRAM – MAIN SECTION (7/8) – 3 7 6 3 1 5 1 5 0 TX BOARD CN902 CN802 ( 7 / 8 ) (Page 69) L946 TP919 10uH EXCEPT MAIN BOARD R930 0 TP920...
  • Page 138 HCD-FX999W/FX1000W SCHEMATIC DIAGRAM – MAIN SECTION (8/8) – 3 7 6 3 1 5 1 5 0 R543 R528 SUPPLEMENT-1 Page 7 R527 R538 L503 C541 C542 C538 C535 0.01 0.01 SUPPLEMENT-1 Page 5 IC507 R516 IC61LV6416-15TG R517 R519...
  • Page 139 HCD-FX999W/FX1000W Ver. 1.2 ELECTRICAL PARTS LIST MAIN 3 7 63 1515 0 NOTE: • Due to standardization, replacements in the • RESISTORS When indicating parts by reference number, parts list may be different from the parts All resistors are in ohms.
  • Page 140 HCD-FX999W/FX1000W MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C262 1-162-966-11 CERAMIC CHIP 0.0022uF 10% C361 1-126-947-11 ELECT 47uF C265 1-162-966-11 CERAMIC CHIP 0.0022uF 10% C362 1-104-658-91 ELECT 100uF...
  • Page 141 HCD-FX999W/FX1000W Ver. 1.2 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C546 1-107-726-91 CERAMIC CHIP 0.01uF C547 1-162-923-11 CERAMIC CHIP 47PF 0 C903 1-112-333-11 ELECT (BLOCK) 330uF 450V (EXCEPT FX999W:MX, TW/FX1000W)
  • Page 142 HCD-FX999W/FX1000W Ver. 1.2 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 0 D914 C953 1-117-214-11 CERAMIC 0.001uF 6-501-193-01 DIODE 1SS355WTE-17 C954 1-100-566-91 CERAMIC CHIP 0.1uF 0 D915 8-719-977-28 DIODE DTZ10B...
  • Page 143 HCD-FX999W/FX1000W Ver. 1.2 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark IC504 6-707-095-01 IC BH2210FV-E2 IC505 8-759-825-15 IC LC89056W-E L946 1-414-398-11 INDUCTOR 10uH IC506 6-707-754-01 IC CXD9862R L947 1-414-398-11 INDUCTOR...
  • Page 144 HCD-FX999W/FX1000W MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R147 1-216-864-11 SHORT CHIP R320 1-216-864-11 SHORT CHIP R151 1-216-864-11 SHORT CHIP R152 1-216-864-11 SHORT CHIP R321 1-216-864-11 SHORT CHIP...
  • Page 145 HCD-FX999W/FX1000W MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R410 1-216-845-11 METAL CHIP 100K 1/10W R530 1-216-809-11 METAL CHIP 1/10W R411 1-216-845-11 METAL CHIP 100K 1/10W R412 1-216-845-11 METAL CHIP...
  • Page 146 HCD-FX999W/FX1000W Ver. 1.2 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R595 1-216-809-11 METAL CHIP 1/10W R662 1-216-841-11 METAL CHIP 1/10W R596 1-216-821-11 METAL CHIP 1/10W R664 1-216-813-11 METAL CHIP...
  • Page 147 HCD-FX999W/FX1000W Ver. 1.2 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 0 R925 R756 1-216-821-11 METAL CHIP 1/10W 1-216-797-11 METAL CHIP 1/10W R760 1-216-809-11 METAL CHIP 1/10W 0 R926...
  • Page 148 HCD-FX999W/FX1000W Ver. 1.2 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark < THERMISTOR > 0 TH901 1-805-841-21 THERMISTOR, NTC 3.0 (FX999W:MX, E32, TW) 0 TH901 1-805-842-21 THERMISTOR, NTC 6.0 (FX999W:E3, E13, SP, AUS/FX1000W) < VARISTOR >...
  • Page 149 HCD-FX999W/FX1000W 3 7 63 1515 0 MEMO L 13942296513 u163 http://www.xiaoyu163.com...
  • Page 150 Ver. Date Description of Revision 2005.06 2005.08 Addition of HCD-FX999W:E13 model (220-230V AC area in E model) and HCD-FX1000W MAIN board changed to Suffix -15 from Suffix -14 (Supplement-1) 2005.10 Addition of HCD-FX999W: Taiwan model 2005.11 Addition of Note on DMB10 board replacement...

This manual is also suitable for:

Hcd-fx1000w

Table of Contents