Murata LBEE5PK2AE User Manual

Murata LBEE5PK2AE User Manual

Wlan+bluetooth module

Advertisement

WLAN+Bluetooth Module User Manual
Part Number: LBEE5PK2AE
LBEE5PK2AE has been FCC/ISED certified as Single Modular Approval with the following IDs.
FCC ID: VPYLB2AE
The module is limited to OEM installation ONLY. The OEM integrator is responsible for ensuring
that the end-user has no manual instruction to remove or install module.
Therefore, the final host product must be submitted to Murata for confirmation that the
installation for the module into the host is in compliance with regulations of FCC and IC Canada.
Specially, if an antenna other than the model documented in the Filing is used, a Class 2
Permissive Change must be filed with the FCC.
Changes or modifications not expressly approved by the manufacturer could void the user's
authority to operate the equipment.
This module has been approved by FCC to operate with the antenna types with the maximum
permissible gain indicated. Antenna types not included in this list, having a gain greater than the
maximum gain indicated for that type, are strictly prohibited for use with this device. The
following antennas have been certified in combination with the module. Refer to next pages for
the antenna application guidance.
(a) Monopole PCB antenna with peak gains of 3.0dBi (2.4GHz) and 3.3dBi (5GHz);
(b) External dipole antenna with peak gains of 3.4dBi (2.4GHz) and 4.75dBi (5GHz);
temperature is -40°C~85°C.
The operational
Antenna Application Guidance – Monopole PCB antenna
IC ID: 772C-LB2AE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LBEE5PK2AE and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Murata LBEE5PK2AE

  • Page 1 WLAN+Bluetooth Module User Manual Part Number: LBEE5PK2AE LBEE5PK2AE has been FCC/ISED certified as Single Modular Approval with the following IDs. FCC ID: VPYLB2AE IC ID: 772C-LB2AE The module is limited to OEM installation ONLY. The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module.
  • Page 2 Antenna Application Guidance – External dipole antenna FCC Statements Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause...
  • Page 3 Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC ID: VPYLB2AE”...
  • Page 4 Utilisez les types d'antennes énumérés ci - dessous et indiquez le gain maximal admissible. Le gain du type d'antenne non inclus dans cette liste est supérieur au gain maximal de l'un des types énumérés et ne doit pas être utilisé avec cet équipement. Le contenu spécifique de l'inspection comprend les trois points suivants.
  • Page 5 (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
  • Page 6 Le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et5 470-5 725 MHz doit se conformer à la limite de p.i.r.e.; Le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz)doit se conformer à...
  • Page 7 External Dipole Antenna 4.75 PCB Antenna UNII-3 External Dipole Antenna 4.75 The PCB Antenna is permanently attached, can’t be replaced. There is only one antenna port, which is shared by all the radios by time divided. The module doesn’t have a permanent antenna. The following antennas are certified to be FCC/ISED regulatory conformity.
  • Page 8 fabricant est fortement recommandé de confirmer la conformité avec les exigences de la fcc / (é metteur lorsque le module est installé dans l'hôte. le dispositif d'accueil doivent avoir une é tiquette indiquant contient FCC ID: VPYLB2AE,IC:772C-LB2AE...

Table of Contents