Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Intellisystem ThermalTronix TT-1040S-UTCM
Summary of Contents for Intellisystem ThermalTronix TT-1040S-UTCM
- Page 1 ThermalTronix TT-1040S-UTCM TT-1075S-UTCM Thermal Imaging Camera User Manual...
- Page 2 Warnings Please avoid aiming the lens at extreme high temperature radiation source, such as the sun, molten steel or laser in any situation; otherwise the detector may be damaged. Please do not touch the lens to avoid contaminating and damaging. Please pay attention to protect the lens to avoid causing abrasion, scratches even breaches, otherwise, it will affect the device performance badly, even damage the device.
-
Page 3: Table Of Contents
Table of Contents Overview ..................3 Getting started ................4 2.1. How to assembly ....................4 2.2. Control panel....................... 4 2.3. Interfaces & connectors..................6 2.3.1. Video output interface ................6 2.3.2. Multiple interface ..................6 Operation guide ................7 3.1. -
Page 4: Overview
1. Overview The Figure.1.1 shows the overall dimension of the camera. Figure.1.1 Overview of the camera Figure.1.2 Back of the camera... -
Page 5: Getting Started
2. Getting started 2.1. How to assembly 1．Check all units are in accordance with the packing list. 2．Make sure all parts are well-protected in the carry case. 3．Carefully take out the camera and other accessories. 4．Connect the video connector to the monitor. 5．Connect the power adapter and power cable 6．Connect the power cable to the power supply to power on the camera. - Page 6 The five keys have the below functions respectively: UP key. When the menu is activated, press UP to adjust the selected parameters. The parameter value will be increased after pressing. When the menu is not activated, press UP to focus forwards. DOWN key.
-
Page 7: Interfaces & Connectors
2.3. Interfaces & connectors 2.3.1. Video output interface Figure.2.3.1.1 Video output interface The above figure is a BNC video output interface. 2.3.2. Multiple interface Figure.2.3.2.1 Multiple interface The definition of each pin is as below: Pin name Description +12V Positive power input Power ground RS485A RS485+... -
Page 8: Operation Guide
3. Operation guide 3.1. Menu description 3.1.1. Main menu Press MENU button to activate main control menu. Press UP or DOWN button to change the Option value. Press MENU button until Exit: option is selected and press UP button or DOWN button to exit. - Page 9 0: Suitable for observation of big-object under good weather condition 1: Suitable for observation of target within sky-line under good weather condition 2～9: User-defined based on different practical occasions. Note: when Auto 0 and 1, Mode X cannot be adjusted; when Auto 2, Mode X can be adjusted.
-
Page 10: System Menu
In System menu, press M button to select Com: XXX, and press + or – button to enter the password: +-MC+-, will pop up the below interface: BaudRate: Protocol: Exit: Figure.3.1.3.1 Communication menu ID: XXX ID number, range: 0~+255. BaudRate: XXX Set Baud rage value; Protocol: XXX Select the communication protocol. Three options: INTELLISYSTEM, PELCO-D and PELCO-P;... -
Page 11: Mode Menu
Exit: Exit configuration setup. Press MENU button to select the Exit option and press UP button to exit the menu. 3.1.4. Mode menu In System menu, press M button to select Mode: XXX and press + or – button to enter the password: +-MC+-, will pop up the below interface: Mode: Gain: Bright: Save: Exit: Figure.3.1.4.1 Mode menu... -
Page 12: Auto Imaging Mode Setup
If so, the system usually has no need to do single pixel correction. The camera running built-in calibration mechanism can do calibration anytime. Besides, it is normal when you hear some “click” noise during calibration. 3.2.3. Auto imaging mode setup Setup: Press MENU button until Auto: XXX is activated, press UP button or DOWN button to select needed mode. -
Page 13: Gain Setup
3.2.5. Gain setup Setup: Press MENU button until G: XXX option is selected. Press UP button or DOWN button to adjust gain parameter value. Exit: Press MENU button until Exit: option is selected and press UP button or DOWN button to exit. Note: this function is only valid when the auto imaging mode setup is Auto 0 or Auto 1. -
Page 14: Image Enhancement Setup
3.2.8. Image enhancement setup Setup: Press MENU button until E: XXX option is selected. Press UP button or DOWN button to set needed enhancing state. Exit: Press MENU button until Exit: option is selected and press UP button or DOWN button to exit. -
Page 15: Troubleshooting
4. Troubleshooting Please follow the below table to diagnose and solve the problem. If problem is still exited, please contact our service center. Trouble Reasons and solutions Power cable is not connected correctly →Connect the power cable again The camera can not power ... -
Page 16: Technical Specifications
5. Technical specifications ThermalTronix Item TT-1040S-UTCM TT-1075S-UTCM Uncooled FPA micro bolometer Detector type Array 384×288 size/format Pixel size 25um Wave range 8-14um Focal length 40 mm 75mm Detector IFOV 13.7°×10.3° 7.3°×5.5° ≤100mK@30℃ NETD Focus Electric focusing Frame rate 50HZ Special 0.63mrad 0.33mrad resolution... - Page 17 Power ≤6W Power supply consumption External power YES (DC12V±20%) Video output Communication Interface RS485 interface Control PELCO-D/PELCO-P/INTELLISYSTEM protocol...
Need help?
Do you have a question about the ThermalTronix TT-1040S-UTCM and is the answer not in the manual?
Questions and answers