Faults In The Gas Installation/Smell Of Gas; Moving The Appliance By The Gas Line Or Door Handle; Electrical Connection; Levelling The Cooker - Bosch HGV74W323Q Instruction Manual

:
If the gas pressure in your gas supply grid!
for natural gas (G20) is higher than 25 mBar, for LPG (G30) is
higher than 36 mBar, for LPG (G31) is higher than 45 mBar, you
must use your appliance in connection with a suitable gas
regulator, for safety reasons. Connection, maintenance and
configuration of the gas regulator must be performed by an
authorised installation expert. If you do not know the gas pressure
in your gas supply grid, please ask your local supply grid operator.

Faults in the gas installation/smell of gas

If you notice a smell of gas or faults in the gas installation, you
must
immediately shut off the gas supply and/or close the gas
■
cylinder valve
immediately extinguish all naked flames and cigarettes
■
switch off electrical appliances and lights
■
open windows and ventilate the room
■
call the after­sales service or the gas supplier
■
Moving the appliance by the gas line or door
handle
Do not move the appliance while holding the gas line; the gas pipe
could be damaged. There is a risk of a gas leak! Do not move the
appliance while holding it by the door handle. The door hinges
and door handle could be damaged.

Electrical connection

Caution!
Have the appliance set up by your after-sales service. A 16 A
■
fuse is required for connection. The appliance is designed for
operation at 220-240 V.
If the electricity supply drops below 180 V, the electrical ignition
■
system does not work.
Any damage arising from the appliance being connected
■
incorrectly will invalidate the guarantee.
If the supply cord is damaged, it must be replaced by the
■
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
For the after-sales service
Caution!
The appliance must be connected in accordance with the data
■
on the rating plate.
Only connect the appliance to an electrical connection that
■
meets the applicable provisions. The socket must be easily
accessible so that you can disconnect the appliance from the
electricity supply if necessary.
Please ensure the availability of a multi-pin disconnecting
■
system.
Never use extension cables or multiple plugs.
■
For safety reasons, this appliance must only be connected to an
■
earthed connection. If the safety earth terminal does not comply
with regulations, safety against electrical hazards is not
guaranteed.
You must use a H 05 W-F type cable or equivalent for the
■
appliance connection.

Levelling the cooker

Always place the cooker directly on the floor.
1. Pull out the plinth drawer and lift it up and out.
There are adjustable feet at the front and rear on the inside of
the plinth.
2. Use an Allen key to raise or lower the adjustable feet as
necessary until the cooker is level (picture A).
3. Push the plinth drawer back in (picture B).
66
$

Wall fixing

To prevent the cooker from tipping over, you must fix it to the wall
using the enclosed bracket. Please observe the installation
instructions for fixing the oven to the wall.

Setting up the appliance

0LQ



The appliance must be set up directly on the kitchen floor and in
■
line with the specified dimensions. The appliance must not be
set up on any other object.
The distance between the top edge of the oven and the bottom
■
edge of the extractor hood must meet the requirements of the
extractor hood manufacturer.
Ensure that the appliance is not moved again after set up. The
■
distance from the high output burner or wok burner to the fronts
of the adjacent units or the wall must be at least 50 mm.

Measures to be noted during transport

Secure all mobile parts in and on the appliance using an adhesive
tape that can be removed without leaving any traces. Push all
accessories (e.g. baking tray) into the corresponding slots with
cardboard at the edges, in order to avoid damaging the appliance.
Place cardboard or similar between the front and rear side to
prevent knocks against the inside of the glass door. Secure the
door and, if available, the top cover to the appliance sides using
adhesive tape.
Keep the original appliance packaging. Only transport the
appliance in the original packaging. Observe the transport arrows
on the packaging.
If the original packaging is no longer available
pack the appliance in protective packaging to guarantee sufficient
protection against any transport damage.
Transport the appliance in an upright position. Do not hold the
appliance by the door handle or the connections on the rear, as
these could be damaged. Do not place any heavy objects on the
appliance.
%