Coarse Adjustment Mode (Coarse) - Panasonic PT- 65WX51E Service Manual

Raster Setup:
1. Enter to service mode (red CHK).
2. In SET-UP (Roller
CONVERGENCE 1 set all values to 0.
3. Cover Red & Blue lens with caps.
4. Apply an NTSC monoscope pattern.
5. Select DAC COARSE, then press ACTION to enter
to "CONVERGENCE ADJ" mode.
6. Press "0" key on remote.
7. Press ACTION key on remote to enter to
"TEST_POS" mode.
8. Move pattern by pressing VOL right - left and CH
up - down so that the cursor center overlap
monoscope pattern center.
30
Figure 35. Aligning cross-hair
cursor with monoscope pattern
9. Press "5" key on remote to exit superimpose mode
(monoscope pattern disappear).
10. Press "TV/VIDEO" key to enter "DATA_POS" mode
11. Adjust by pressing VOL right - left so that peak of
curve is the same position as center of cursor.
Figure 36. Symmetrical shape
12. Press "TV/VIDEO" key on remote to enter
"OSD_POS" mode.
13. Press "5" key on remote so that monoscope
pattern appears (superimpose mode)
14. Move cursor by pressing VOL right - left and CH
up - down so that
monoscope pattern center
15. Press "0" key to go back to "CONVERGENCE
ADJ" mode.
16. Press "TV/VIDEO" key to cycle through "COARSE
ADJ. MODE" options.
Static Size
C orner
Figure 37. Coarse modes cycle
17. To change to "FINE ADJUSTMENT MODE"
options (DAC FINE), press "TV/VIDEO" key on
remote for at least 3 seconds, to go back to
Service Manual
Guide menu)
cursor center overlap
Skew Linear
Pin K ey
"COARSE ADJ MODE" options press "TV/VIDEO"
on remote again for 3 seconds.
18. In "FINE ADJUSTMENT MODE" options, press
"MUTE" key on remote to switch between "cursor"
mode and "data" mode.
• Cursor mode: Allows cursor movement by
pressing VOL right - left and CH up - down.
• Data mode: Allows making adjustment by
pressing VOL right - left and CH up - down.
19. Either "COARSE ADJUSTMENT MODE" options
or "FINE ADJUSTMENT MODE" options, press "R-
TUNE" repeatedly key on remote to cycle through
different color adjustments (R,G,B,White)
20. To store adjustments press "7", then "ACTION" key
on remote, otherwise press "POWER" then
"ACTION" to exit adjustments without saving.
21. Remote Functions:
• 1, 3. . . . . . . . . . .change color view adj
• 2. . . . . . . . . . . . . . . . . . change pattern
• 7. . . . . . . . . . . . . . . . . . . . . . . save data
• 5. . . . . . . . . . . . . . . . . . . . . . . . . overlap
• POWER . . . . . . . . . . . . . . . . . . . . to exit
• RECALL . . . . . . . . . . . . display values
• R-TUNE . . . . . . . . . . . . . . . cycle colors
• TV/VIDEO . . . . . . . . . . . . change mode
3 secs. . . . . . . change options

Coarse Adjustment Mode (COARSE)

Note: It is strongly recommended to first read and
understand the following section prior to
make any adjustment.
Procedure:
1. Enter to "G-SIZE" mode:
• DAC COARSE
• Press ACTION on remote
• TV/VIDEO (repeatedly)
• R-TUNE (repeatedly)
2. Press "2" repeatedly and apply the pattern of
border and cross.
3. Press RECALL to display values
4. Adjust size so that the line of the border closes to
the screen frame at top, bottom, left and right by
pressing CH up-down and VOL right-left.
Figure 38. H & V Size Adjustment
- 20 -