Page 1
ORDER No.ACED001211C3 AUTOMOTIVE CONSUMER ELECTRONICS CY-TV7000W In-Dash 7.0 Wide Color LCD Monitor SPECIFICATIONS Specifications*...
Page 2
General Power Supply DC 12V (11V - 16V), Test Voltage 14.4V Negative Ground Less than 3A Current Consumption 0.5 Vrms (VTR) Audio Input Sensitivity Pre-output Voltage 0.5 Vrms Video input signal Composite video signal 1.0 Vp-p (75 Video output signal Composite video signal 1.0 Vp-p (75 Display Unit...
1. FEATURES - 7-inch wide LCD color display - Fully powered display positioning mechanism - The speaker for the car navigation system - Equipped with Auto Dimmer - RGB Input Terminals - Video Input Terminals - Video Output Terminals 2. REPLACING THE FUSE Use fuses of the same specified rating (3A).
8. ADJUSTMENT PROCEDURES Note : The following Adjustment Procedures are used Adjustment Remote Controller, with TEST switch. Adapt the Remote Controller to add the TEST Switch (Remote Controller : for CQ-VA707W and so on). 1. Remove the surface sheet. 2. Remove 3 screws. 3.
Page 10
8.1. MONITOR BLOCK [E-8711B] Test Point Adjustment Method Remarks Adjustment No.Adjustment Item Point DC/DC 1 VR761 Adjust VR761 to 5.2V+0.05V, -0V at TP751 TP751 / (+ Color Bar Signal Voltage 5.2V) Generator / Chroma Signal:OFF / White TP984 Level:100% / Unit (VGND) Mode 2 VR901...
Page 11
Test Point Adjustment Method Remarks Adjustment No.Adjustment Item Point 1. Press the TEST button of remote-controller over 2 sec to set Test 3 Remote Setting in test mode. Mode Controller Menu 2. Select a desired adjustment item by up or down button, and press ENTER button to decide, as shown in below.
Page 12
Test Point Adjustment Method Remarks Adjustment No.Adjustment Item Point 1. Adjust BP(Black Level Positive) level to 1.2V. BRIGHT 5 Remote TP982 (G) Color Baar Sinal 2. Confirm that BN(Black Level Negative) is within 3.8V +0.1, - Controller / TP952 Generator / Chroma 0.1V.
Page 13
Test Point Adjustment Method Remarks Adjustment No.Adjustment Item Point 7 Remote TP982 (G) Adjust the remote-controller so that BP of Color Bar Signal BRIGHT B Controller / TP981 (B) each color is same. Generator / Chroma / TP952 Signal:OFF / White (VGL) / Level:100% / Apply TP984...
Page 14
Test Point Adjustment Method Remarks Adjustment No.Adjustment Item Point TINT 10 Remote TP982 (G) Adjust the remote-controller so that Color Bar Signal Controller / TP952 amplitude of four waveforms is same. / If the Generator / Chroma (VGL) / TINT adjustment is no satisfied, readjust Signal:ON / White TP984 step 9.
Page 15
Test Point Adjustment Method Remarks Adjustment No.Adjustment Item Point Prepara 1 IN/Out ANT1 Befor adjustment, perform the following tion Sttings Fixed procedures. 1. Press the TEST button of remote-controller over 2 sec to set in test mode. 2. Select a desired adjustment item by up or down button, and press ENTER button to decide, as shown in below.
Page 16
Test Point Adjustment Method Remarks Adjustment No.Adjustment Item Point 4 L101 TP101A (B) Adjust L101 to obtain for 0V+0.1,-0.1V FM Signal Generator / TP102A between TP101A(B) and TP102A (B). 59.75MHz / Input V / Modulation 7.5kHz / Tuner VCONT 5 VR102 TP104A (B) Adjust VR102 to obtain for 3.2V+0.1V, -0V at FM Signal Generator TP104A (B).
Page 18
PinNo. Name Description I/O Volt 1 VCC1 +5V power supply (5V) 2 VREF Reference voltage 3 R CLAMP Rch clamp detection 4 G CLAMP Gch clamp detection 5 B CLAMP Bch clamp detection 6 DEC.R OUT(NC) 7 DEC.G OUT(NC) 8 DEC.B OUT (NC) 9 ANALOG Rch analog signal input...
Page 19
PinNo. Name Description I/O Volt 31 /VD OUT(NC) 32 /HD OUT(NC) 33 PWM(NC) 34 /RESET Power-on reset signal 35 /VD IN Vertical sync.signal input 36 POL IN 1H reverse pulse input 37 VSS (Connecting to ground) 38 CP IN Horizontal sync. signal input 39 DAC MON(NC)
Page 20
PinNo. Name Description I/O Volt 62 B-Y OUT(NC) 63 R-Y(NC) 64 B-Y(NC) 9.2. Tuner Block IC601 : C2BBGF000203 Name Description Volt(V) 1 KEY1 A/D key 1 signal input I 5.2 2 KEY2 A/D key 2 signal input I 5.2 3 KEY3 A/D key 3 signal input I 5.2 4 LIGHT...
Page 21
Name Description Volt(V) 22 VDDPORT +5V power supply (for I/O port) - 5.2 23 MAIN Main power control signal O 5.2 output 24 SYS System mute signal output MUTE 25 SP MUTE Speaker mute signal output 26 TRANS FM transmit control signal O 5.2 output 27 V NAVI...
Page 22
Name Description Volt(V) 52 TV ANT4 TV Antenna 4 change the signal output 53 TV LOCK TV PLL lock detect 54 TV COM TV PLL data output 55 TV CLK TV PLL clock signal output 56 TV CE TV PLL enable signal output 57 VD TV Vertical Sync selection signal O 5.2...
IC703 : YEAMPQ1CZ1T IC704 : YEAMPC2905E1 11. REPLACEMENT PARTS LIST Notes: 1. Be sure to make your orders of replacement parts according to this list. 2. Important safety notice: Components, identified by mark have special characteristics important for safety. / When replacing any...
Page 31
of these components, use only manufacturer’s specified parts. 3. Location keys in the remarks column indicates the general location of the parts shown in the exploded drawing, as in a load map. 4. The marking (RTL) indicates that Retention Time is limited for this item.After the discontinuation of assembly in production, the item will continue to be available for a specific period of time.
Ref. No. Part No. Part Name & Description Remarks YEFV03542 Magnetic Shield YEFV011987 Magnetic Shield YEFX007565 Cord Clamper YEFR04187 Illumination Cap YEFX0214765 Bracket, LCD YEFS01976 YEFA131562 Case YEFS011578 YEFM021702 Seal YEFA011823 Chassis YEFS011619 YEFX0052443 Spring YEFX0052442 Spring YEP9FX094C Loading Mechanism Ass'y YEFX0214767 Bracket, Connector YEJS06238...