Advertisement
Quick Links
LE-01MR
Electric energy meter,
1-phase
Do not dispose of this device in the trash along with other waste!
According to the Law on Waste, electro coming from households free of charge and can
give any amount to up to that end point of collec� on, as well as to store the occasion of
the purchase of new equipment (in accordance with the principle of old-for-new, regard-
less of brand). Electro thrown in the trash or abandoned in nature, pose a threat to the
environment and human health.
Compliance
MID Directive
Certificate
Purpose
The LE-01MR v2 is a static (electronic), calibrated AC single-pha-
se electricity meter for direct current measurement in a 2-wire
system.
Functioning
The meter provides 4-quadrant energy and power measurement
as well as monitoring of many additional network parameters
such as voltage, current, active power, reactive power, apparent
power, frequency, power factor. The meter has additional, era-
sable active and reactive energy meters. It is also equipped with
RS-485 communication interface with Modbus RTU protocol
support for remote meter reading and configuration. The touch
button located on the front panel of the meter allows you to
select the displayed parameter and change the meter settings.
F&F Filipowski sp. j.
Konstantynowska 79/81, 95-200 Pabianice, POLAND
phone/fax (+48 42) 215 23 83 / (+48 42) 227 09 71
www.fif.com.pl; e-mail: biuro@fif.com.pl
v2
2014/32/EU
0120/SGS0305
- 1 -
Advertisement
Related Manuals for F&F LE-01MR v2
Summary of Contents for F&F LE-01MR v2
- Page 1 MID Directive 2014/32/EU Certificate 0120/SGS0305 Purpose The LE-01MR v2 is a static (electronic), calibrated AC single-pha- se electricity meter for direct current measurement in a 2-wire system. Functioning The meter provides 4-quadrant energy and power measurement as well as monitoring of many additional network parameters such as voltage, current, active power, reactive power, apparent power, frequency, power factor.
- Page 2 The backlit LCD display makes it easy to read the measured values. The parameter is changed by default every 5 seconds or at the frequency set by the user and manually, using the touch button on the front of the casing of the meter. The display is active when the indicator power is on.
-
Page 3: Modbus Registers
Modbus registers Description of measurement and configuration registers availa- ble on the website www.fif.com.pl (on the device’s subpage). Meter address Change of meter address and connection parameters is done via the RS-485 using the touch button on the front of the casing of the meter. - Page 4 Sealing The meter has sealable input and output terminal covers to pre- vent any attempts to bypass the meter. Front panel - 4 -...
-
Page 5: Wiring Diagram
Wiring diagram power input power output N-wire neutral RS-485 output (A) RS-485 output (GND) RS-485 output (B) - 5 -... - Page 6 Mounting 1. Disconnect the power supply. 2. Mount the indicator on the rail in the distribution box. 3. Connect the neutral wire to terminal N. 4. Connect the input phase to terminal 1. 5. Connect the measured circuit or single receiver to terminal 3 (output phase L) and to N.
- Page 7 constant 1000 pulses/kWh communication Modbus address 1*÷245 port RS-485 communication protocol Modbus RTU transmission parameters 9600*, 19200, 38400, 115200 bps parity NONE*, ODD, EVEN stop bits read-out signalling red LED working temperature -25÷55°C terminal 100 A (1, 3 terminals) 25 mm² screw terminals neutral (N terminal) 1 mm²...
-
Page 8: Warranty
Dimensions Warranty F&F products are covered by a 24-month warranty from the date of purchase. The warranty is only valid with proof of purchase. Contact your dealer or contact us directly. CE declaration F&F Filipowski sp. j. declares that the device is in conformity with the essential requirements of The Low Voltage Directive (LVD) 2014/35/EU and the Electromagnetic Compatibility (EMC) Directive 2014/30/UE.