Introduction Important service information Important Diskette fixes are customer-installable. The diskette fixes are posted on the IBM support site (http://www.pc.ibm.com/support/). Advise customers to contact the PC Company HelpCenter at 800-772-2227 if they need assistance in obtaining or installing any diskette fixes.
Symptom-to-FRU Index for the computer you are servicing. Diskette compatibility matrix The compatibility of each of the drives with the diskettes for it is as follows: Diskette drive 3.5-inch ThinkPad TransNote Important service information Diskette capacity 1.0 MB 2.0 MB 4.0 MB Compatibility...
Safety notices: multilingual translations In this manual, safety notices appear in English with a page number reference to the appropriate translation in this section. The safety notices are provided in English, French, German, Italian, and Spanish, as follows: Safety notice 1 Before the computer is powered-on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose...
Page 8
Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet, kann geringe Mengen Nickel und Cadmium enthalten. Sie darf nur durch die Verkaufsstelle oder den IBM Kundendienst ausgetauscht werden. Sie darf nicht zerlegt, wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Die Batterie kann schwere Verbrennungen oder Verätzungen...
Page 9
Safety notices Continuation of Safety notice 2 DANGER: Alcune batterie di riserva contengono una piccola quantità di nichel e cadmio. Non smontarle, ricaricarle, gettarle nel fuoco o nell’acqua né cortocircuitarle. Smaltirle secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni locali).
Page 10
Deséchelas tal como dispone la normativa local. Utilice sólo baterías que se encuentren en la lista de piezas al sustituir la batería. La utilización de una batería no apropiada puede provocar la ignición o explosión de la misma. ThinkPad TransNote...
Page 11
Safety notices Safety notice 4 DANGER: The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water.
Page 12
No la recargue, ni quite el conector polarizado, ni la desmonte, ni caliente por encima de los 100°C (212°F), ni la incinere ni exponga el contenido de sus celdas al agua. Deséchela tal como dispone la normativa local. ThinkPad TransNote...
Page 13
Safety notices Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water for at least 15 minutes. Seek medical care if any symptoms from the fluid are present after washing.
Page 14
Aunque las baterías principales tienen un voltaje bajo, una batería cortocircuitada o con contacto a tierra puede producir la corriente suficiente como para quemar material combustible o provocar quemaduras en el personal. ThinkPad TransNote Safety notices...
Page 15
Safety notices Safety notice 8 Before removing any FRU, power off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables. Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension, débranchez tous les cordons d’alimentation des socles de prise de courant, retirez la batterie et déconnectez tous les cordons d’interface.
Safety information The following section contains the safety information that you need to be familiar with before servicing an IBM mobile computer. General safety Follow these rules to ensure general safety: v Observe good housekeeping in the area of the machines during and after maintenance.
Electrical safety Observe the following rules when working on electrical equipment. Important Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges.
This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-IBM features or options not covered by this inspection guide. If any unsafe conditions are present, you must determine how serious the apparent hazard could be and whether you can continue without first correcting the problem.
Insulation must not be frayed or worn. 4. Remove the cover. 5. Check for any obvious non-IBM alterations. Use good judgment as to the safety of any non-IBM alterations. 6. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage.
Laser compliance statement Some IBM Personal Computer models are equipped from the factory with a CD-ROM drive or DVD drive. CD-ROM drives or DVD drives are also sold separately as options.
Page 21
When a CD-ROM drive or DVD drive is installed, note the following: CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure. O uso de controles, ajustes ou desempenho de procedimentos diferentes daqueles aqui especificados pode resultar em perigosa exposição à...
Page 22
Non fissare il fascio, non guardarlo direttamente con strumenti ottici e evitare l’esposizione diretta al fascio. Radiación láser al abrir. No mire fijamente ni examine con instrumental óptico el haz de luz. Evite la exposición directa al haz. ThinkPad TransNote Laser compliance statement...
General descriptions This chapter includes descriptions for any ThinkPad model that has the PC-Doctor DOS diagnostics program. Some descriptions might not apply to your particular computer. Read this first Before you go to the checkout guide, be sure to read this section.
Page 24
Missing parts might be a symptom of unauthorized service or modification. v If the spindle of a hard-disk drive become noisy, it may have been subjected to excessive force, or dropped. ThinkPad TransNote Read this first...
Service Web site When the latest maintenance diskette and the system program service diskette are available, a notice will be posted on http://www.pc.ibm.com/partner/infotips/ Using Recovery CD To create Service Partition and install the preloaded system from Recovery CD, do the following;...
HDP and master HDP have been forgotten, the password cannot be removed and the hard disk will not be accessible. Supervisor password: A supervisor password (SVP) protects the system information stored in the IBM BIOS Setup Utility so that ThinkPad TransNote Related service information...
5. Reinstall the backup battery and the battery pack. (B) If SVP is installed: 1. Turn on the computer by pressing and holding F1. 2. Enter the SVP. The IBM BIOS Setup Utility menu appears. 3. Select Password, using the cursor keys to move down the menu.
To enter standby mode, do any of the following: v Press Fn + F4. v Close the ThinkPad TransNote computer. (To prevent the computer from entering standby mode when the computer is closed, click Will not suspend even if LCD is closed in the Power Management Properties window.
v If the battery indicator blinks orange, indicating that the battery power is low. (Alternatively, if Hibernate when battery becomes low has been selected in the ″Power Management Properties″ window, the computer goes into hibernation mode.) Note: Even if you don’t set the low-battery alarm, the charge indicator lets you know that the battery is low, and then the computer enters the power-saving mode automatically.
For some possible configurations of the computer, PC-Doctor might not run correctly. To avoid this problem, you need to initialize the computer setup by using the IBM BIOS Setup Utility before you run PC-Doctor. In the IBM BIOS Setup Utility screen, press F9, Enter, F10, then Enter.
Page 31
Interactive Tests. To test it, use the audio device test in the Other Devices (Diagnostics). v Video Adapter test supports only the LCD display on ThinkPad TransNote. Before running PC-Doctor DOS, detach the external monitor. 4. Run the applicable function test.
7. Check that the battery pack supplies power when you power on the computer. If you suspect a power problem, see the appropriate one of the following power supply checkouts: v “Checking the ac adapter” on page 29 v “Checking operational charging” on page 29 ThinkPad TransNote Checkout guide...
v “Checking the battery pack” on page 30 v “Checking the backup battery” on page 31 v “Checking the sub-battery” on page 31 Checking the ac adapter You are here because the computer fails only when the ac adapter is used: v If the power problem occurs only when the port replicator is used, replace the port replicator.
4 to 30 K . If the resistance is not correct, replace the battery pack. If the resistance is correct, replace the system board. ThinkPad TransNote Terminal Voltage (V dc) + 0 to + 16.8 Ground (−)
Checking the backup battery Do the following: 1. Power off the computer, and unplug the ac adapter from it. 2. Remove the battery pack (for the removal procedure, see “1010 Battery pack” on page 56). 3. Remove the backup battery (for the removal procedure, see “1060 Backup battery and sub-battery”...
Retaining serial numbers. Restoring the serial number of the system unit Retaining the UUID . Removing and replacing a FRU. Removing the ThinkPad TransNote 1010 Battery pack. 1020 DIMM 1030 Mini PCI adapter 1040 Hard-disk drive and hard-disk drive cover 1050 Keyboard 1060 Backup battery and sub-battery .
Page 38
Endurimer/leather cover replacing kit . Miscellaneous parts . Optional FRUs . Common parts list . Tools . Power cords (system) . Notices Trademarks . ThinkPad TransNote . 135 . 136 . 136 . 139 . 140 . 140 . 141 .
Universal serial bus (USB) connectors v RJ11 v RJ45 CompactFlash card 56.6 Kbps v Internal microphone v Internal speaker v Software control volume IrDA 1.1 Type-I or II 56-watt type or 72-watt type ThinkPad TransNote Product overview ® III processor ™ SpeedStep...
The system status indicators show the status of the computer, as follows: Indicator 1 Battery 2 Standby status (continued) ThinkPad TransNote Meaning Green: The battery is fully charged. Blinking green: The battery has enough power to operate, but is being charged.
If both the power-on indicator and the standby indicator are on, you can use the computer after it returns from the standby mode and the standby indicator goes off. ThinkPad TransNote Product overview...
(continued) ThinkPad TransNote Applicable test 2. Diagnostics --> Systemboard Diagnostics --> Other Devices --> IBM AC Adapter, IBM Battery 1 1. Diagnostics --> Video Adapter 2. Interactive Tests --> Video 1. Make sure the modem is set up correctly.
1. Turn on the computer and check the air turbulence at the louver of the rear side. 2. Run Diagnostics --> Other Devices --> IBM Fan. See “Identifying problems with the FlipTouch display” on page 47. See “Identifying problems with the ThinkScribe digital notepad”...
Page 44
Fn + Fn + ─ Fn + ─ Fn + = Fn + Left shift Gives the same function as pressing the ThinkPad TransNote Description Brightness down. Brightness up. Display output on the computer display, an attached external monitor, or both.
If the symptom is not described there, go to “Intermittent problems” on page 48. Note For an IBM device not supported by diagnostic codes in the ThinkPad notebook computers, see the manual for that device. Numeric error codes...
Page 46
FRU or action, in sequence 1. Charge the battery pack. 2. Battery pack. 1. Reseat the hard-disk drive. 2. Load Setup Defaults in IBM BIOS Setup Utility. 3. Hard-disk drive. 4. System board. Run interactive tests of the keyboard and the auxiliary input device.
Page 47
02F7 Fail-safe timer NMI failure. Symptom-to-FRU index FRU or action, in sequence 1. Load Setup Defaults in IBM BIOS Setup Utility. 2. DIMM. 3. System board. 1. Load Setup Defaults in IBM BIOS Setup Utility. 2. Replace the backup battery.
2. Backup battery. 3. System board. 1. Check that the operating system has no failure and is installed correctly. 2. Enter IBM BIOS Setup Utility and see whether the hard-disk drive and the diskette drive are properly identified. 3. Reseat the hard-disk drive.
A power-on password or a supervisor password is set. Type the password and press Enter. A hard-disk password is set. Type the password and press Enter. Start the ThinkPad Configuration program and set the Screen expansion function. ThinkPad TransNote...
LCD screen unreadable. v Characters missing pixels. v Screen abnormal. v Wrong color displayed. Horizontal or vertical lines displayed on LCD. ThinkPad TransNote Symptom-to-FRU index FRU or action, in sequence System board. 1. Reseat all LCD connectors. 2. LCD assembly.
To analyze a problem with the FlipTouch display, do the following: 1. Make sure that the FlipTouch display is enabled: v IBM BIOS Setup Utility --> Config --> FlipTouch Display 2. Insert the PC-Doctor DOS disk in the diskette drive, and turn on the system unit.
10 times. 2. If no error is detected, do not replace any FRUs. 3. If any error is detected, replace the FRU shown by the FRU code. Rerun the test to verify that no more errors exist. ThinkPad TransNote Symptom-to-FRU index...
2. Visually check each FRU for damage. Replace any damaged FRU. 3. Remove or disconnect all of the following devices: a. Non-IBM devices b. Devices attached to the port replicator c. Printer, mouse, and other external devices d. Battery pack e.
Read this section carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. An IBM ThinkPad computer addresses this problem with special nylon-coated screws that have the following characteristics: v They maintain tight connections.
The Universally Unique Identifier (UUID) is a 128-bit number uniquely assigned to your computer at production and stored in the EEPROM of your system board. The algorithm that generates the number is designed to provide FRU replacement notices ThinkPad TransNote...
Page 56
1. Install the ThinkPad hardware maintenance diskette version 1.61, and restart the computer. 2. From the main menu, select 4. Assign UUID. A new UUID is created and written. If a valid UUID already exists, it is not overwritten. ThinkPad TransNote FRU replacement notices...
Establish personal grounding by touching a ground point with one hand before touching these units. You must use an electrostatic discharge (ESD) strap (P/N 6405959) to establish personal grounding. Removing and replacing a FRU ThinkPad TransNote...
Removing the ThinkPad TransNote Note: There are two models of the ThinkPad TransNote, one is for a right-handed person and the other or a left-handed person. This manual depicts the right-handed model, but all remove and replace processes remain the same, except the one for the pen holder kit (Section 1070).
Page 59
Removing and replacing a FRU Note for FlexFold hinge The external portion of the ThinkPad TransNote cover is made of a Endurimer material. This material can be folded in such a way to allow use of the computer or digital notepad without placing either one face down on a surface.
To avoid possible injury: (1) replace only with a battery of the type recommended by IBM, or an equivalent, (2) keep the battery pack away from fire, (3) do not expose it to water or rain, (4) do not attempt to disassemble it, (5) do not short-circuit it.
Page 61
Removing and replacing a FRU ThinkPad TransNote...
Removing and replacing a FRU 1020 DIMM v Battery pack (1010) (continued) ThinkPad TransNote...
Page 63
Removing and replacing a FRU Note: Loosen the screw 3 , but do not remove it. (continued) ThinkPad TransNote...
Page 64
Removing and replacing a FRU ThinkPad TransNote...
Page 65
2 . Make sure that the card is firmly fixed in the slot and does not move easily. DIMM cover installation notice: Attach the latch of the cover firmly by pressing the part shown in the following figure, and then tighten the screw. ThinkPad TransNote...
Removing and replacing a FRU 1030 Mini PCI adapter v Battery pack (1010) Note: Loosen the screw 1 , but do not remove it. (continued) ThinkPad TransNote...
Page 67
Removing and replacing a FRU ThinkPad TransNote...
Page 68
(A) is for the LAN feature and (B) is for the modem feature. This slot also supports a Mini PCI modem card or a Mini PCI network card. Step 7 depends on the card type. Disconnect either (A), (B) or both. ThinkPad TransNote Removing and replacing a FRU...
Page 69
25 degrees. Insert the card into the socket 1 . Pivot the card until it snaps into place 2 . Make sure that the card is firmly fixed in the slot and does not move easily. (continued) ThinkPad TransNote...
Page 70
If the sheet does not stick to the slot on the video card, just leave it and install the Mini-PCI slot cover not to pinch the cable or the black sheet. ThinkPad TransNote Removing and replacing a FRU...
Never remove the drive while the system is operating or is in suspend mode. v Battery pack (1010) Note: Loosen the screw 2 , but do not remove it. (continued) Removing and replacing a FRU ThinkPad TransNote...
Page 72
Note: The hard disk is attached to the cover, but the cover is a separate FRU. When installing: Make sure that the label on the ThinkPad TransNote Removing and replacing a FRU hard-disk drive faces the bottom side of the computer and that the hard-disk...
Removing and replacing a FRU 1050 Keyboard v Battery pack (1010) v DIMM (1020) v Hard-disk drive and hard-disk drive cover (1040) Note: Loosen the screw 2 , but do not remove it. (continued) ThinkPad TransNote...
Page 74
Removing and replacing a FRU (continued) ThinkPad TransNote...
Page 75
Removing and replacing a FRU When installing: Make sure that the keyboard connector is firmly attached. ThinkPad TransNote...
Page 76
2. Push the E key and D keys and O key and L keys 1 to latch the keyboard to the frame; then connect the keyboard connector 2 . ThinkPad TransNote Removing and replacing a FRU follows:...
1060 Backup battery and sub-battery CAUTION: There is a danger of an explosion if the backup battery is incorrectly replaced. The lithium battery (IBM P/N 02K6572 UL-recognized component [file no. MH12210]) contains lithium and can explode if it is not properly handled or disposed of.
Page 78
Removing and replacing a FRU When installing: Make sure that the connector is firmly attached. ThinkPad TransNote...
A ( a ) and then slide A in the direction of the arrow b . Then tighten the screw. (continued) Removing and replacing a FRU Screw cap Torque 39.2 Ncm (4 kgfcm) 39.2 Ncm (4 kgfcm) ThinkPad TransNote...
Page 80
Step Screw (quantity) M2.5 × 3 mm, nylon-coated (1) M2.5 × 3 mm, nylon-coated (1) ThinkPad TransNote Removing and replacing a FRU Screw cap Torque 39.2 Ncm (4 kgfcm) 39.2 Ncm (4 kgfcm)
A ( a ) and then slide A in the direction of the arrow b . Then tighten the screw. (continued) Removing and replacing a FRU Screw cap Torque 39.2 Ncm (4 kgfcm) 39.2 Ncm (4 kgfcm) ThinkPad TransNote...
Page 82
Step Screw (quantity) M2.5 × 3 mm, nylon-coated (1) M2.5 × 3 mm, nylon-coated (1) ThinkPad TransNote Removing and replacing a FRU Screw cap Torque 39.2 Ncm (4 kgfcm) 39.2 Ncm (4 kgfcm)
Removing and replacing a FRU side from the Endurimer or leather cover, remove only the screws marked with ″>″ beside the screw holes. Screw cap none ThinkPad TransNote Torque 39.2 Ncm (4 kgfcm) 39.2 Ncm (4 kgfcm) 39.2 Ncm (4 kgfcm)
Page 84
Removing and replacing a FRU (continued) ThinkPad TransNote...
Page 85
Removing and replacing a FRU ThinkPad TransNote...
Screw (quantity) M2.5 × 3 mm, nylon-coated (3) M2.5 × 3 mm, nylon-coated (2) (continued) ThinkPad TransNote Removing and replacing a FRU side from the Endurimer or leather cover, remove only the screws marked with ″>″ beside the screw holes.
Page 87
When installing: Align the right edge of the base plate (continued) Removing and replacing a FRU tape ( a ) to the b -part of the base plate, as shown in the following figure. ThinkPad TransNote...
Page 88
Before attaching new digitizer onto the Endurimer, do the followings; 1. Wipe the surface of the digitizer sheet a gently with a dry soft cloth to remove a stain or a dust on it. 2. Stick the digitizer label b onto the digitizer sheet. ThinkPad TransNote...
For the process of changing the cover from right-handed orientation to left-handed orientation, see “4010 Changing the orientation of a left- or right-handed model” on page 124. Removing and replacing a FRU ThinkPad TransNote...
Hard-disk drive and hard-disk drive cover (1040) v Keyboard (1050) v Backup battery and sub-battery (1060) v Digital-pen holder kit (1070) v Computer side (1080) After procedure 2 , lay the LCD unit down and then turn the computer side upside down. (continued) ThinkPad TransNote...
Page 91
Step Screw (quantity) M2.5 × 4 mm, nylon-coated (3) Removing and replacing a FRU Torque 39.2 Ncm (4 kgfcm) ThinkPad TransNote...
Page 92
Removing and replacing a FRU When installing: Make sure that all of the claws of the cover are firmly fixed into place. ThinkPad TransNote...
Mini PCI adapter (1030) v Hard-disk drive and hard-disk drive cover (1040) v Digital-pen holder kit (1070) v Computer side (1080) Step Screw (quantity) M2.5 × 4 mm, nylon-coated (2) (continued) Removing and replacing a FRU Torque 39.2 Ncm (4 kgfcm) ThinkPad TransNote...
Page 94
Note: Pull the black sheet out from the space between the connector cables, but do not strip it off from the video card. (continued) ThinkPad TransNote Removing and replacing a FRU...
Page 95
Removing and replacing a FRU ThinkPad TransNote...
Page 96
Make sure that the connector on the bottom side of the video card is firmly connected. v Make sure that the connector cables are not pinched under the video card as in the following figure. ThinkPad TransNote Removing and replacing a FRU following:...
1130 System board and PC card slot assembly v Battery pack (1010) v DIMM (1020) v Mini PCI adapter (1030) v Hard-disk drive and hard-disk drive cover (1040) v Digital-pen holder kit (1070) v Computer side (1080) v Video card (1120) (continued) ThinkPad TransNote...
Page 98
Removing and replacing a FRU Note: Loosen the screw 2 , but do not remove it. (continued) ThinkPad TransNote...
Page 99
Removing and replacing a FRU (continued) ThinkPad TransNote...
Page 100
Removing and replacing a FRU When installing: Make sure that the keyboard connector is firmly attached. (continued) ThinkPad TransNote...
Page 101
Step Screw (quantity) M2.0 × 3.5 mm, nylon-coated (4) (continued) Removing and replacing a FRU Torque 24.5 Ncm (2.5 kgfcm) ThinkPad TransNote...
Page 102
Step Screw (quantity) M2.5 × 16 mm, nylon-coated (5) M2.5 × 4.0 mm, nylon-coated (11) (continued) ThinkPad TransNote Removing and replacing a FRU Torque 39.2 Ncm (4 kgfcm) 39.2 Ncm (4 kgfcm)
Page 103
Step Screw (quantity) M2.0 × 3.5 mm, nylon-coated (4) M2.5 × 4.0 mm, nylon-coated (1) (continued) Removing and replacing a FRU Torque 24.5 Ncm (2.5 kgfcm) 39.2 Ncm (4 kgfcm) ThinkPad TransNote...
Page 104
Note When removing or installing the system board and the PC card slot assembly, take care not to damage the eject buttons. (continued) ThinkPad TransNote Removing and replacing a FRU...
Page 105
Removing and replacing a FRU ThinkPad TransNote...
Page 106
When installing: Make sure that all of the claws of the ThinkPad TransNote Removing and replacing a FRU base plate are firmly fixed into place and the plate is firmly attached in the plastic base.
Digital-pen holder kit (1070) v Computer side (1080) v Video card (1120) v System board and PC card slot assembly (1130) Step Screw (quantity) M2.0 × 3.5 mm, nylon-coated (1) (continued) Removing and replacing a FRU Torque 24.5 Ncm (2.5 kgfcm) ThinkPad TransNote...
Page 108
Removing and replacing a FRU ThinkPad TransNote...
Page 109
Removing and replacing a FRU Cable routing: Route the connector cable as shown in the following figure. ThinkPad TransNote...
Digi-pen holder kit (1070) v Computer side (1080) v Video card (1120) v System board and PC card slot assembly (1130) Step Screw (quantity) M2.5 × 4.0 mm, nylon-coated (4) ThinkPad TransNote Removing and replacing a FRU Torque 39.2 Ncm (4 kgfcm)
Page 111
Removing and replacing a FRU When installing: Remove the protective sheet from the thermal rubber on the fan assembly. ThinkPad TransNote...
Removing and replacing a FRU 2010 LCD assembly v Battery pack (1010) v Mini PCI adapter (1030) v Hard-disk drive and hard-disk drive cover (1040) v Digital-pen holder kit (1070) v Computer side (1080) v Video card (1120) (continued) ThinkPad TransNote...
Page 113
Removing and replacing a FRU (continued) ThinkPad TransNote...
Page 114
Removing and replacing a FRU (continued) ThinkPad TransNote...
Page 115
Step Screw (quantity) M2.5 × 3 mm, nylon-coated (4) Removing and replacing a FRU Screw cap Torque 39.2 Ncm (4 kgfcm) ThinkPad TransNote...
Hard-disk drive and hard-disk drive cover (1040) v Digital-pen holder kit (1070) v Computer side (1080) v Video card (1120) v LCD assembly (2010) Step Screw (quantity) M2.5 × 4.0 mm, nylon-coated (4) (continued) ThinkPad TransNote Removing and replacing a FRU Torque 39.2 Ncm (4 kgfcm)
Page 117
Removing and replacing a FRU (continued) ThinkPad TransNote...
Page 118
Removing and replacing a FRU When installing: Before tightening the screws, make sure that all of the latches are firmly latched. ThinkPad TransNote...
The FlipTouch panel that covers the LCD display is made of glass. When removing or replacing the LCD panel, take care not to touch the edge of the FlipTouch display glass to avoid personal injury. (continued) Removing and replacing a FRU ThinkPad TransNote...
Page 120
Step Screw (quantity) M2.5 × 4.0 mm, nylon-coated (4) (continued) ThinkPad TransNote Removing and replacing a FRU Torque 39.2 Ncm (4 kgfcm)
Page 121
Removing and replacing a FRU (continued) ThinkPad TransNote...
Page 122
Step Screw (quantity) M2.5 × 4.0 mm, nylon-coated (1) ThinkPad TransNote Removing and replacing a FRU Torque 39.2 Ncm (4 kgfcm)
Page 123
When installing, do as follows: 1. Attach the connector on the bottom side of the inverter card to the LCD cable connector ( 1 ). (continued) Removing and replacing a FRU ThinkPad TransNote...
Page 124
LCD panel on the rear cover ( 3 ). 3. Align the upper left corner of the LCD panel with the upper left corner of the rear cover ( 4 ). (continued) ThinkPad TransNote Removing and replacing a FRU...
Page 125
( 6 ). Make sure that the other connector, which was connected in the installing procedure 1 , is not disconnected when you lift the inverter card. When routing the cable, do as following figure. ThinkPad TransNote...
Page 126
Removing and replacing a FRU 5. Tighten the screws 7 and 8 . ThinkPad TransNote...
Mini PCI adapter (1030) v Hard-disk drive and hard-disk drive cover (1050) v Digital-pen holder kit (1080) v Computer side (1090) v Video card (1130) v LCD assembly (2010) v LCD front bezel (2020) v LCD panel and Inverter card (2030) ThinkPad TransNote...
(See “1070 Digital-pen holder kit” on page 75.) 3. Remove the computer side. (See “1080 Computer side” on page 79.) 4. Remove the ThinkScribe digital notepad. (See “1090 ThinkScribe digital notepad assembly” on page 82.) (continued) ThinkPad TransNote Removing and replacing a FRU...
Page 129
5. Paste new velcro tapes 1 on the bottom side of the computer side and remove the old tapes 2 as shown in the following figures. Right-handed model to left-handed model Left-handed model to right-handed model (continued) Removing and replacing a FRU ThinkPad TransNote...
Page 130
6. Paste new base plate tape 1 on the bottom side of the computer side, and then remove the other one 2 . Right-handed model to left-handed model Left-handed model to right-handed model (continued) ThinkPad TransNote Removing and replacing a FRU...
Page 131
7. Paste new velcro tapes 1 on the bottom side of ThinkScribe digital notepad and remove the old tapes 2 as shown in the following figures. Right-handed model to left-handed model Left-handed model to right-handed model (continued) Removing and replacing a FRU ThinkPad TransNote...
Page 132
Note: When replacing the Endurimer or the system-digi cable, make sure that the black connector of the system-digi cable is attached to the computer and the white connector is attached to the digital notepad assembly. (continued) ThinkPad TransNote Removing and replacing a FRU...
Page 133
Connect the system-digi cable to the computer side and then paste new system board plate. b. Paste the new tape (Tape for digitizer 2) aligning the ″┌″ marks on the base plate. (continued) Removing and replacing a FRU ThinkPad TransNote...
Page 134
Tighten the screws and paste the screw caps. Screw holes for a left-handed model. Screw holes for a right-handed model. Screw hole for both models. (continued) ThinkPad TransNote Removing and replacing a FRU...
Page 135
Connect the system-digi cable 1 to the digital notepad and then paste the digitizer plate 2 . b. Paste the new tape (Tape for digitizer 2) 3 aligning the ┌ marks on the digitizer base plate. (continued) Removing and replacing a FRU ThinkPad TransNote...
Page 136
Tighten the screws and paste the screw caps. Screw holes for a left-handed model. Screw holes for a right-handed model. 12. Install the digital-pen holder kit. (See “1070 Digital-pen holder kit” on page 75.) ThinkPad TransNote Removing and replacing a FRU...
FlipTouch control button Mute button Battery pack Battery pack latch TrackPoint buttons Microphone jack Infrared port Built-in monaural speaker Built-in microphone Stereo line-in jack Stereo headphone jack Digital pen ThinkScribe digital notepad (see “ThinkScribe digital notepad” on page 135.) ThinkPad TransNote Locations...
Parts list Overall ThinkPad TransNote Parts list...
Page 141
Pen holder kit for right-handed for left-handed System-Digi cable Plate for audio card Audio card DIMM* (see “Optional FRUs” on page 142) Top cover WW (continued) ThinkPad TransNote Parts list 08K6466 08K6468 08K6481 05K9286 08K6594 08K3158 08K3338 08K3252...
Page 142
Optional port replicator* (see “Optional FRUs” on page 142) Label of digitizer for non-English models for GDL (French) for EMEA (German and French) for FUJI (Japanese) Telephone cable* Form holder ThinkPad TransNote Parts list 02K6684 02K6682 08K6576 08K6574 08K6578 02K6686...
Tape for base plate v Tape for digi-base v Tape for digi-base3 v Velcro tape v Screw caps (small) v Screw caps Endurimer for right-handed Leather cover for right-handed ThinkPad TransNote Parts list 02K5498 02K5496 02K5501 02K5503 02K5493 02K5492...
Shield tape v Shield tape 2 v Spring protection sheet v Screw, M2.5 x 4 mm v System board plate v Screw caps, small v Screw caps, large v Screw caps (continued) ThinkPad TransNote Parts list 04P3291 04P3293 04P3292...
ThinkPad hardware maintenance diskette version 1.61 Note: Download the file from the Web site. Power cords (system) IBM power cords for a specific region are usually available only in that region: For 2-pin power cords: Region Canada, Taiwan, United States of America...
Notices References in this publication to IBM products, programs, or services do not imply that IBM intends to make these available in all countries in which IBM operates. Any reference to an IBM product, program, or service is not intended to state or imply that only that IBM product, program, or service may be used.
Need help?
Do you have a question about the TransNote and is the answer not in the manual?
Questions and answers