VENDINGBOX 540 Manual page 9

Vending-Box COMPANY
service or a qualified technician.
For each level of the feeder we can match a product
which will be dispensed from it. Such matching forms a
scheme of loading for a certain level. Thank to matching
a product to a level and forming such a scheme of
loading, we can load this space with products directly to
the feeder through an open left door-leaf.
13.1 Change of the width of the product cell
In order to make the
product cell wider, on the
selected level you must
remove a blocking dowel
(1) of certain partition (2)
and pull it out completely.
To install additional
partition, you must do this
in the reverse order.
If a new partition is installed, set it so as the
blocking dowel prevented it from falling out.
A bigger notch in the front part of the partition
makes it possible to pull out the dowel in the cell below.
Regulation of the width of opening sliding
13.2
flaps
The width of opening of the sliding flaps depends on the
element of the lock limiting
full opening (1). If full
opening of the flap and 15
cells on the level re needed,
the cap covering the lock
must be removed. To set the
width of opening the flap to
the ½ width, the blocking
element must be screwed
and covered with a plastic
cap.
13.3 Configuration of the feeder in the user's
panel/assigning the product
In the menu of configuration of the feeder, it is possible
to set a scheme of loading and size of the product cell
for each level of the feeder.
In the picture below you can see two levels of the
device marked 1 and 2. On the level 1, the width of the
opening of loading window is set to ½, there are 30 cells
on the level. In this case a product for loading scheme
has not been selected so this level can be loaded through
flaps. There is no possibility of product loading directly
to the drum.
For the level 2, the full width, 15 cells for the level and
a certain product matched have been set. Next to the
product icon, its category, defined type and name are
displayed, and we can see the number of items of the
certain product matching this level, here it is 15.
In order to change the width of the product cell, you
must select the proper configuration, pressing the button
on the chosen level on the left side of the panel. To
match or cancel a product for a certain level, you must
press the button on the right side of the panel.
In order to make the dispenser work properly, the width
of cells must be set according to physical configuration
of the feeder, and products must be matched with
certain levels according to the needs.
To install or replace the SIM card, flat key
10mm and cross-head screwdriver are needed.
Before replacing the SIM card, the machine
must be switched off. The device produces
short, regular sounds informing that data is
recorded. After recording the data, you must wait 30
seconds.
During removing the cover, you must be careful not to
damage the controller.
14 Replacement of the SIM card
The SIM card socket is located on the controller plate of
the user's panel. To replace the SIM card, screws fixing
the cover of the controller of the user's panel must be
unscrewed.
Insert the SIM card to the tray. Unlock the tray
moving it slightly towards OPEN and then
move outside of the socket. Insert the SIM
card so that the cut off corner of the card fitted
the cut off corner of the socket. Close the tray with the
installed SIM card and lock , moving it towards LOCK.
1. Cut off corner,
2. SIM card tray
After installation of the SIM card, fix carefully the
cover of the user's panel controller.
To ensure the proper work of the SIM card, configure
the settings of the net interfaces. There is a detailed
description of it in the chapter: 3.3 GSM interface.
15 Configuration of net interfaces
Configuration of the parameters of net interfaces is
possible to be done in the menu of advanced settings,
accessible only for a user like serviceman. The device
may be equipped with maximum three net interfaces:
ETHERNET, WLAN and GSM and the equipment for
connection with the ETHERNET and GSM is standard
one with every device. After introducing changes in the
menu of the advanced settings, the machine should be
updated.
Model 540