Maintenance - VENDINGBOX 540 Manual

Vending-Box COMPANY

MAINTENANCE

1 Cleaning and conservation
The device contains a battery ensuring its proper
switching off in case of disconnecting from the outer
power supply. If the device is not used for a longer time,
it is recommended to regularly connect it with the outer
power supply (every second month) for 48 hours in
order to charge the battery.
The device does not need any special conservation, but
it should be placed in a clean, dry area. Keeping the
device clean (e.g. dusting) should be done with the use
of a dump piece of cloth with a non-aggressive
detergent. Avoid 'soaking' the machine, especially its
electronic elements. Regularly check if the drum
rotation is fluent. The rotation should be even without
any jamming. Also the movement of flaps should be
checked and rails should smeared occasionally to
decrease friction. The performance quality of the
mechanism blocking the feeder rotation should be
controlled .
2 Periodic inspection
The device needs warranty periodic inspection every 12
months in order to control all the mechanisms not
available to the user, such as drive, transmission,
electromechanical elements. Information on the
warranty periodic inspection can be obtained at the
authorized service.
3 List of spare parts
The producer guarantees full availability of all spare
parts for the dispenser, however during normal use of
the device, only two types of parts might be needed.
One type is parts which get worn out during the use of
the machine, and the second type is parts needed during
re-configuration of the feeder and door with the sliding
flaps.
3.1 Parts being the subject to replacement
Due to the used technical solutions, the machine
contains few elements which are subject to replacement.
Here is the list of such parts:
1. Default power supply battery
2. RTC (Real Time Clock) battery
3. Toothed belt of the drive transmission
4. Pin locking the mechanism of brake
4 Replacement of consumable elements
4.1 Replacement of the battery
In case of losing the power supply, the machine is
maintained by the default power supply battery, which
is fixed behind the main device controller. It allows to
record the machine data onto the micro SD card.
To replace the battery you need a flat key
10mm and a cross-head screwdriver.
Before changing the battery: Switch off the
machine.
Re-start the device. This option is available in
the main interface menu. It is available only for
SERVICEMAN.
While moving the module, be careful not to
damage the controller.
On the front panel, turn out the screws fixing the
module of the main controller and move it gently
forwards to enable moving the battery.
Next, remove the yellow pressure plate by turning out
two fixing screws.
Be careful not to short connectors of the battery
with the yellow pressure plate and the drum.
Now the battery may be moved and the cables
disconnected. There are three cables connected with the
battery: red (+), black (-) and temperature sensor.
1. Pressure plate
2. Screws fixing the module of the main
controller
3. Battery connector
New battery should be firstly connected with the
machine according to the marking: red (+), black (-).
Place the battery on the base and tighten the yellow
pressure of the battery so that the temperature sensor is
in the opening of the pressure.
After finishing the battery replacement, gently insert the
module of the main controller, turn in the fixing screws
and put in the fuse to the socket F3.
4.2 Replacement of the RCT (Real Time Clock)
batteries
To install or replace the SIM card, you need a
flat key 10mm and a head-cross screwdriver.
The battery socket is located on the controller
plate on the user's panel. In order to replace the battery,
turn out the screws fixing the controller cover on the
user's panel.
Before replacing the SIM card you must switch
off the machine. The device produces short
regular sound signals which inform about the
process of data recording. After recording the data, wait
for 30 sec.
While removing the batteries, unlock the batteries first.
The new battery must be put in the socket so that the
battery gets locked.
After installation of the battery, fix carefully the
controller cover on the user's panel.
Model 540