Table of Contents
Advertisement
Vending-Box COMPANY
Extra
information
on
configuration
is
to
be found
Configuration of net interfaces.
11.2 WLAN
The second step is starting the WLAN
interface. This icon informs about the state
of connection with the net. If the connection
is successful, the icon color will change from
gray to blue. If the WLAN
switched off, this stage is omitted. The wireless net
interface is not supplied with the standard equipment.
Extra information on WLAN connection configuration
is to be found in the chapter: Configuration of net
interfaces.
11.3 Packet data GPRS connection
The last net interface started is the GSM
modem for connection of packet data. This
icon informs about the state of connection
with the GSM net. The status information
shows the signal strength, 0-4 bars and the
state of packet data connection. If the connection is
successful, the edging will change the color from gray
to blue. If the GSM interface is switched off, this stage
is omitted.
Extra information on GSM connection configuration is
to be found in the chapter: Configuration of net
interfaces.
11.4 Time set correctness
Next step is verification of the time set in the
Real Time Clock (RTC). In case of
discharging or damaging the battery, the
device will download the current time from
the configured time server using the
connection with the internet. While downloading the
information on the current time from the internet, the
device informs about it generating three short sound
signals.
If downloading the current time from the server is
necessary, it is essential to set the connection with the
internet with the use of ETHERNET, WLAN or GSM.
If the verification of RTC time is successful, the icon
will change the color from gray to blue.
11.5 VPN connection
Next step is connection with the VPN
(Virtual Private Network). The showed icon
informs about the state of connection with
the net. If the connection is successful, the
icon color will change from gray to blue. If
the VPN connection is switched off, this
stage is omitted.
11.6 Device data reading
Finally, reading and verification of data
recorder in the non-volatile memory of the
device. If the operation is successful, the
showed icon will change from gray to blue.
11.7 Starting the dispensing application
After correct introduction of all the active steps of the
starting screen, dispensing application is started. The
default screen after starting is the screen of waiting for
the user's logging in with the use of the proximity card.
ETHERNET
connection
in
the
chapter:
interface is
After starting the application, the device is ready to
normal work such s dispensing, loading or configuration
described in chapter: Configuration of the device.
12 Switching off the device
To switch off the device, you must turn the main power
supply switch to the 0 position. In the emergency
situation, the machine may be switched off by
unplugging it from the power supply socket, at the back
of the machine.
After disconnecting from the power supply, the
controller of the user's panel is powered from the
battery and produces a sound signal for about a minute,
informing about power disconnection. If the power is
supplied back within this time, the machine will
immediately restore its work.
Switching on the power supply with the opening door
sensor switched on causes automatic rotation of the
drum in order to set its position. . Remember not to
leave protruding elements in the feeder and to move
aside from the feeder after switching the machine on.
If the power is not supplied back, the machine will stop
producing the sound signal and will get switched off. If
the power is supplied when the machine does not
produce the sound signal any longer, all the starting-up
procedure described in the previous chapter will occur.
Emergency power supply is realized with the use of
installed battery. The battery used is able to ensure
maintaining the operation of the controller four times
per day at the minimum, after power disconnection, for
all the cycle of the battery durability.
CONFIGURATION OF THE DEVICE
13 Configuration of the feeder
Product cells may differ in size. The user has a
possibility to individually adjust the size of shelf to the
product even when the machine is already in use. In the
feeder of the 540 dispenser you can set 6 different sizes
of product cells.
Selecting a cell type, you must set it for the whole level
in the feeder. It is not possible to set two or more
different sizes of product cells on one level. Changing
the width of a cell, you
must properly set also the
element
defining
the
opening width of the
sliding flap.
The chart below shows all
available types together
with
dimensions
and
number of cells for each
type setting in the whole
feeder.
Number of
A
cells
540
80mm
270
80mm
270
170mm
180
260mm
135
170mm
90
260mm
It is possible to change the height of product cells
during the use of the device. However, this kind of
reconfiguration can be done only by an authorized
Model 540
B
C
D
75mm 275mm 15mm
150mm 275mm 30mm
75mm 275mm 15mm
75mm 275mm 15mm
150mm 275mm 30mm
150mm 275mm 30mm
Advertisement
Table of Contents
