1. Manuals
  2. Brands
  3. Nortel Manuals
  4. Network Hardware
  5. IVR 2.5/S
  6. Manual

Nortel IVR 2.5/S Manual

Aculab-based e1 cas/isdn pri
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
1
Nortel IVR 2.5/S
Aculab-Based E1 CAS/ISDN PRI Signaling
Guide
Product release 2.5/S
Standard 1.0
July 1997

Advertisement

Table of Contents
loading

Related Manuals for Nortel IVR 2.5/S

Summary of Contents for Nortel IVR 2.5/S

  • Page 1 Nortel IVR 2.5/S Aculab-Based E1 CAS/ISDN PRI Signaling Guide Product release 2.5/S Standard 1.0 July 1997...
  • Page 2 IVR and Nortel are registered trademarks of Northern Telecom in the U.S. and Canada. IVR Generator 2.0/S and Meridian 1 are registered trademarks of Northern Telecom. DEC and VT 420 are registered trademarks of Digital Equipment Corporation.
  • Page 3 Publication history July 1997 Standard 1.0 release of the Aculab-Based E1 CAS/ISDN PRI Signaling Guide for Nortel IVR 2.5/S. Nortel IVR 2.5/S Aculab-Based E1 CAS/ISDN PRI Signaling Guide...

  • Page 4: Table Of Contents

    S1 I/O addressing........B-3 Nortel IVR 2.5/S...

  • Page 5: Introduction

    DNIS, ANI, and CLC. This is indicated by 0, 1, and 3 respectively in the CINFO cell. Attempting to retrieve other information forces the application to take the NO_DATA branch from the cell. Nortel IVR 2.5/S Aculab-Based E1 CAS/ISDN PRI Signaling Guide...

  • Page 6: System Requirements

    Chapter 2: System requirements The base Nortel IVR 2.5/S system already includes the system requirements listed here for installing and using the Aculab-based E1 CAS/ISDN PRI Signaling option update for MRS 3.02.02. Specifically, these requirements • MRS 3.02.02 software running on the MRS •...

  • Page 7: E1 Cas/Isdn Pri Enhancements

    Aculab hardware-based options. • MRS 3.02.02 also provides new E1 CAS signaling firmware. MRS currently supports one Aculab E1/ISDN card per system. Both 30-port and 60-port Aculab cards are supported. Nortel IVR 2.5/S Aculab-Based E1 CAS/ISDN PRI Signaling Guide...

  • Page 8: E1 Signaling Systems

    3-2 E1 CAS/ISDN PRI enhancements E1 Signaling Systems MRS 3.02.02 supports E1 CAS signaling systems for the following countries and protocols: • Belgium • Brazil • China #1 • Mexico • Malaysia (Singapore) • Ericsson E&M (EEMA) ISDN PRI MRS 3.02.02 supports the following E1 ISDN PRI network protocol: •...

  • Page 9: Installing The Aculab E1/Pri Signaling Option

    Before installing this option, your MRS system must have MRS version 3.02.02 installed. The base Nortel IVR 2.5/S system includes MRS 3.02.02 software, so it should already be installed on your MRS. This chapter describes how to install the Aculab-based E1/PRI Signaling option hardware and software onto your MRS system.

  • Page 10: Installing The Aculab E1/Pri Signaling Option Hardware

    4-2 Installing the Aculab E1/PRI signaling option Installing the Aculab E1/PRI signaling option hardware Procedure 4-1: Installing the Aculab E1/PRI signaling option hardware Wear an antistatic wrist band when handling the option cards. Unpack the Aculab E1/PRI Signaling option card(s) and remove them from the antistatic bag.
  • Page 11 Processing ACL-30 E1 Module PEB bus Additional Modules (voice processing, fax, TTS, Voice Voice ASR resources, etc.) Processing Processing Module Module ACL-60 E1 PEB 0 PEB 1 t=Internal Terminator T=External Terminator Nortel IVR 2.5/S Aculab-Based E1 CAS/ISDN PRI Signaling Guide...

  • Page 12: Installing The Aculab-Based E1/Pri Signaling Option Software

    4-4 Installing the Aculab E1/PRI signaling option Installing the Aculab-based E1/PRI signaling option software Note: New systems are pre-loaded at the factory with both CAS and Enhanced DPNSS protocols. The software installation procedures discussed in this section are required only for restoring the software or if the signaling option is purchased separately after the initial purchase of the base system.
  • Page 13 At the /sci/install> prompt, type package and press <Enter>. The following prompt is displayed: Insert the floppy - type q to quit or hit ENTER to continue: Nortel IVR 2.5/S Aculab-Based E1 CAS/ISDN PRI Signaling Guide...
  • Page 14 /sci/install> Remove the diskette. Run the Nortel customization script (refer to the section “Nortel Customization Procedure” in Chapter 6 of the Nortel IVR 2.5/S Product Overview Guide ). Continue with Procedure 4-4 on page 4-9. Note: If it is not necessary for you to configure the country parameters, then restart the MRS now as described in steps 10 to 13 on page 4-12.
  • Page 15 Wait until the Ready light on the front panel of the MRS begins flashing before continuing. This step ensures that all MRS processes were stopped. On the MRS/AP, there is no Ready light to observe (just proceed to the next step). Nortel IVR 2.5/S Aculab-Based E1 CAS/ISDN PRI Signaling Guide...
  • Page 16 /sci/install> Remove the diskette. Run the Nortel customization script (refer to the section “Nortel Customization Procedure” in Chapter 6 of the Nortel IVR 2.5/S Product Overview Guide ). Continue with Procedure 4-5 on page 4-13. Note: If it is not necessary for you to configure the country parameters, then restart the MRS now as described in steps 15 to 18 on page 4-16.

  • Page 17: Configuring E1 Cas Country Parameters

    Procedure 4-4: Configuring country parameters for CAS signaling option At the /sci/install> prompt, type country. The system displays the copyright information for the Nortel Internationalization utility. When prompted, press <Enter> to continue. The system displays the present country configuration, followed by this...
  • Page 18 4-10 Installing the Aculab E1/PRI signaling option 1. Australia 18. Morocco 2. Austria 19. Netherlands 3. Belgium 20. New Zealand 4. Brazil 21. Norway 5. China 22. Portugal 6. Denmark 23. South Africa 7. Finland 24. Spain 8. Germany 25. Sweden 9.
  • Page 19 ACL Type = xx port ACL Firmware = xxxxx Number of DNIS (DDI) digits = x Number of ANI (CLI) digits = x Do you wish to continue the installation [y/n]: Nortel IVR 2.5/S Aculab-Based E1 CAS/ISDN PRI Signaling Guide...
  • Page 20 Setting up new kernel environment The system must now be rebooted for the new parameters to take affect The Nortel xxx Country Parameters have now been installed. /sci/install> Make sure that the last installation diskette has been removed from the disk drive.

  • Page 21: Configuring Isdn Pri Country Parameters

    Procedure 4-5: Configuring country parameters for the ISDN PRI signaling option At the /sci/install> prompt, type country. The system displays the copyright information for the Nortel Internationalization utility. When prompted, press <Enter> to continue. The system displays the present country configuration, followed by this...
  • Page 22 4-14 Installing the Aculab E1/PRI signaling option 1. Australia 18. Morocco 2. Austria 19. Netherlands 3. Belgium 20. New Zealand 4. Brazil 21. Norway 5. China 22. Portugal 6. Denmark 23. South Africa 7. Finland 24. Spain 8. Germany 25. Sweden 9.
  • Page 23 Do you wish to continue the installation [y/n]: Type y and press <Enter> to continue. The system displays the following prompt: Do you wish to manually edit the Aculab Space.c file? [y/n] Nortel IVR 2.5/S Aculab-Based E1 CAS/ISDN PRI Signaling Guide...
  • Page 24 Installing new unix on the boot file system Setting up new kernel environment The system must now be rebooted for the new parameters to take affect The Nortel xxx Parameters have now been installed. /sci/install> Make sure that the last installation diskette has been removed from the disk drive.

  • Page 25: Activating The Signaling Option

    Activating the signaling option After the signaling option components (hardware and software) are installed, the option must be activated. Contact your Nortel service provider for assistance. Make sure the modem is connected to the system for remote login, as described in Appendix A.

  • Page 26: Appendix A: Accessing The Service Console Interface

    “Using a modem to access the SCI” on page A-3 • “Using the LAN to access the SCI” on page A-5 • “Accessing the SCI on an MRS/AP” on page A-6 Nortel IVR 2.5/S Aculab-Based E1 CAS/ISDN PRI Signaling Guide...

  • Page 27: Using A Terminal To Access The Sci

    Press <Enter> and the following message should display: <system name> MRS Service Access Port Revision 3.02 Copyright 1991-1996, Nortel. All Rights Reserved login: At the login: prompt, enter the appropriate account name. The default passwords for these accounts are as follows:...

  • Page 28: Using A Modem To Access The Sci

    Using a modem to access the SCI In North America, a modem that supports a 9600 kbps baud rate is shipped with every MRS system. Outside North America, a Nortel-recommended modem is provided by the distributor or customer. This modem must be connected to the MRS system when the system is installed.
  • Page 29 Trained Service Personnel admin supervise Site Administrators user nortel Routine Maintenance After you log in, the system prompts you for your terminal type. If the default terminal type displayed is correct, press <Enter>; otherwise, type in the correct terminal type.

  • Page 30: Using The Lan To Access The Sci

    Internet address instead of the default address shown. This address is noted on your equipment list. Note 2: If the host is an X Window-based UNIX workstation, Nortel recommends that this command be issued from an xterm window.

  • Page 31: Accessing The Sci On An Mrs/Ap

    Trained Service Personnel admin supervise Site Administrators user nortel Routine Maintenance After you log in, the system prompts you for your terminal type. If the default terminal type displayed is correct, press <Enter>; otherwise, type in the correct terminal type.

  • Page 32: Appendix B: Card Configurations

    2 3 4 5 6 7 8 Port 1 JP6 JP4 JP16 BNC connectors G100650 Table B-1: S1 I/O addressing for ACL-30 E1 Interface Ports I/O Address Ports 00-29 0x320 - 0x323 Nortel IVR 2.5/S Aculab-Based E1 CAS/ISDN PRI Signaling Guide...
  • Page 33 B-2 Card configurations Notes: The ACL-30 is always a clock master on the PEB. Set the appropriate jumpers to ground the shield for each BNC connector in use. BNC Connector Grounding Jumper Port 1 TX1 JP32 - ON Port 1 RX1 JP31 - ON Each PEB connection requires one D/320-SC card.

  • Page 34: Aculab Acl-60 E1 Interface (75 Ω

    JP10 2 3 4 5 6 7 8 Port 1 JP16 BNC connectors G100651 Table B-2: S1 I/O addressing for ACL-60 E1 Interface Ports I/O Address Ports 00-59 0x320 - 0x323 Nortel IVR 2.5/S Aculab-Based E1 CAS/ISDN PRI Signaling Guide...
  • Page 35 B-4 Card configurations Notes: The ACL-60 is always a clock master on the PEB. Set the appropriate jumpers to ground the shield for each BNC connector in use. BNC Connector Grounding Jumper Port 2 TX2 JP34 - ON Port 2 RX2 JP33 - ON Port 1 TX1 JP32 - ON...
  • Page 36 Telecom reserves the right to make changes in design or components as progress in engineering and manufacturing may warrant. IVR and Nortel are registered trademarks of Northern Telecom in the U.S. and Canada. IVR Generator 2.0/S and Meridian 1 are registered trademarks of Northern Telecom. DEC and VT 420 are registered trademarks of Digital Equipment Corporation.

Table of Contents