Release notes for the baystack instant internet version 7.11.2 (10 pages)
Summary of Contents for Nortel BCM200
Page 1
Small and Medium Business Solutions Overview and Configuration Guide ATTENTION Clicking on a PDF hyperlink takes you to the appropriate page. If necessary, scroll up or down the page to see the beginning of the referenced section. NN47910-200...
Page 2
Users must take full responsibility for their applications of any products specified in this document. The information in this document is proprietary to Nortel Networks.
Page 4
1) 53 Interconnection of peer sites using BSR222 (topology 2 with topology 2) 54 Interconnection of main and remote sites using BSR222 and BCM200/400 (topology 2 with BCM 200/400) 55 Interconnection of BSR222 and an incumbent router (topology 1 with topology...
Getting help over the phone from a Nortel Solutions Center If you do not find the information you require on the Nortel Technical Support Web site, and have a Nortel support contract, you can also get help over the phone from a Nortel Solutions Center.
Page 6
6 How to get help www.nortel.com/erc Getting help through a Nortel distributor or reseller If you purchased a service contract for your Nortel product from a distributor or authorized reseller, contact the technical support staff for that distributor or reseller.
New in this release The following section details what is new in the Nortel Small and Medium Business (SMB) Solutions Overview and Configuration Guide for SMB (Small and Medium Business) portfolio Release 2.0. New products See the following sections for information about new products.
BCM telephony call server cannot be justified. The linked SMB sites described in this guide are verified for small deployment using BCM50 and larger deployment using BCM200/400 in the following interconnected reference topologies: •...
SMB preconfiguration checklist Document title BAP120 1.0 Quick Installation for the Nortel Business Access Point 120 (NN47921-300) Using the Nortel Business Access Point 120 (NN47921-301) Business Access Point 120 Release Notes (NN47921-400) BES50 1.0 Quick Installation for the Nortel Business Ethernet Switch 50 Series...
BES without a DHCP/BOOTP server present and browse to the factory default address for the management interface. Existing products The following existing Nortel products integrate with new SMB portfolio release 2.0 products. SMB Portfolio 1.0 products...
Page 16
Optional Antennas for BAP120 Other Nortel products Business Communications Manager BCM50 BCM50 Expansion and Media Bay Modules BCM400 BCM200 BCM200/400 Expansion and Media Bay Modules Landline IP telephones IP Phone 1120E IP Phone 1140E IP Phone 2001 IP Phone 2002...
Element Manager client window when you double-click the respective devices from the Element Manager navigation panel. A Web management interface also exists for the BCM50 and BCM200/400, making seamless management of a converged SMB network possible. Element Manager software can reside on any local area network (LAN)-connected PC and be launched when required.
IP address using DHCP from the router DHCP server. Personal computers (PC), personal digital assistants (PDA), laptops, and Nortel IP phones obtain private IP addresses from the same DHCP server. Voice support is provided with Nortel IP phones, Voice Soft-Clients, and the BCM communications server.
SNMP client enabled. IP addressing for SMB devices and DHCP Nortel recommends using DHCP to obtain IP addresses for SMB devices and end nodes (such as PCs and IP phones). The SMB reference topologies 2 and 3 rely on a DHCP server running on the BSR222 in the subnet (typically occupying address 192.168.1.1).
DHCP server on the BCM50 to serve IP addresses to IP phones running on laptops and personal digital assistants (PDA) • illustrates a fully managed and converged Nortel subsystem for a mixed environment • provides virtual local area network (VLAN) traffic segregation and Guest...
Page 25
"Installation and configuration workflow for a converged small site (mixed-vendor environment)" (page 26) The installation sequence is a critical component of this minimal configuration scenario. Nortel recommends that you wait a few minutes between configuring and installing each device to allow each device to complete the boot cycle.
Page 34
Leave the remaining default values. Connecting the IP phones Nortel IP phones are fully DHCP-enabled, and require no setup. Each IP Phone receives a DHCP address from the BCM50. After the IP Phones are connected to the BCM50, the details appear in the IP Terminal Details tab in the Telephony Resources window.
Page 39
Configuring a smaller converged site (Greenfield and infrastructure replacement) 39 The installation sequence is a critical component of this minimal configuration scenario. Nortel recommends that you wait a few minutes between configuring and installing each device to allow each device to complete the boot cycle.
BAP120 devices to each BES to provide wireless access capability to node devices on the subnet. A remote BCM50, BCM200, or BCM400 supplies telephony support. See the figure remote site (Greenfield and infrastructure replacement)" (page This reference topology •...
Page 45
Configuring a smaller remote site (Greenfield and infrastructure replacement) 45 The installation sequence is a critical component of this minimal configuration scenario. Nortel recommends that you wait a few minutes between configuring and installing each device to allow each device to complete the boot cycle.
"Interconnection of peer sites using BSR222 (topology 2 with topology 2)" (page 54) • "Interconnection of main and remote sites using BSR222 and BCM200/400 (topology 2 with BCM 200/400)" (page 55) • "Interconnection of BSR222 and an incumbent router (topology 1 with topology 3)" (page 56) •...
Interconnection of main and remote sites using BSR222 and BCM200/400 (topology 2 with BCM This reference interconnection has the following features: • Each site has a BSR222 and BCM50. A branch tunnel connects the sites, and the BCM50 acts as a gateway to each site.
Interconnection of main and remote sites using BSR222 and BCM200/400 This reference interconnection has the following features: • The remote site has one BSR222, and the main site has a BCM200/400 with VPN capability. A branch tunnel connects the sites. •...
The SMB factory security defaults described in defaults" (page 61) deployment. Nortel recommends that you change the factory default user IDs and that you change passwords frequently using strong password methodology. If you have a security policy in place that prevents the use of network management protocols such as SNMP, follow the guidelines in this section to establish your network without SNMP.
BAP120 also supports Wireless Bridging. Wireless bridging can be used to reduce the requirement for wired ports from BES devices and allows you to daisy-chain access points wirelessly. For engineering rules for such deployments, contact Nortel technical support. Port count and device support table Non-PoE BES devices, 48 ports, 24 with PoE Small and Medium Business Solutions Overview and Configuration Guide...
finite list of third-party vendor WiFi client devices. Nortel has augmented this interoperability testing coverage with a longer list of vendors. The following table lists third-party WiFi clients, beyond the standard list used for testing, that have shown successful functional interoperability results.