Chasing M2 User Manual page 4

Remote controller
EN
The Chasing M2 remote controller had integrated communication and control. It
connects directly to the drone via the included tether and connects wirelessly to
your mobile phone/tablet via Wi-Fi. It allows the drone to display a live video feed on
your phone/tablet, which enables users to control the drone in real-time. The base
station's HDMI output can also be used to display a live video feed to a larger screen.
9
5
2
4
3
1. Power switch: Turns controller on/off
2. Power Indicator: Green (High power), Blue
(Medium power), Red (Low power)
3. Wi-Fi switch button: Short press to switch
5Ghz/2.4Ghz Wi-Fi
4. Signal Indicator:
2.4G : 2.4Ghz Wi-Fi indicator, always on
when working
5G: 5Ghz Wi-Fi indicator, always on when
working
ROV(drone): Indicates the communication
status between the controller and the
drone (Steady light indicates successful
connection; Blinking light indicates
disconnection.)
5. One-key reset: Short press to reposition
the ROV return to a horizontal state/
Long press to switch control mode
6. Unlock: Unlock/Lock，current state of
the Thruster will show on the App
7. Led Control: On/off led light (0%50%100%)
8. Safety Buckle: Can be used with a safety rope
9. Control Sticks: Used to control the
naviga-tion of the ROV
* Note: Do not put the controller in the water to avoid damaging the device, damages
caused by water ing-ress are not covered by the warranty.
05
17
18
9
8
15
7
14
6
10
1
12
10.Robotic Arm Control: Press and hold to
enable/disable the grabber claw function;
press to change the floodlight brightness
level
11. Photo/Video: Short press to take
photos, long press to start / end
recording video
12. Right Angel Adjustment: Adjust the roll
angle or control the opening and
closing of the grabber claw
13. Left Angel Adjustment: Adjust the pitch
angle
14. Type-c Port: Direct connection with
mobile phone/tablet device
15. HDMI Socket: 1080P HD image
real-time output
16. Tether Connection Socket/Charging
socket
17. Phone/Tablet Clamp: Used to attach
phone/tablet mount to mounting
bracket
18. Clamp Button: Pull apart the two ends
and put in the phone/tablet, then
press this button to tighten
Handle indicators introduction
Battery：
Red： 10%↓ Red light flashes quickly； 10-29% Red light always on.
Blue： 30-69% Blue light always on.
Green： 70-100% Green light always on.
Signal Indicator:
2.4G： 2.4Ghz Wi-Fi indicator， always on when working.
5G： 5Ghz Wi-Fi indicator， always on when working.
ROV： Indicates the communication status between the controller and the
ROV (Steady light indicates successful connection, Blinking light
indicates disconnection.)
Gesture back Button：
16
The blue light is always on when the ROV is in a non-horizontal position.
11
13
Unlock Button：
Locking: No lights ； Unlocking: Blue light on.
Led Control Button：
Bright light： Blue light always on; Low light: Blue light flash; No light:
Blue light off.
100/200 meters Tether & Winder
The tether is used to connect the drone and the remote controller The winder is
used to store the tether.
1. Tether connectors
2. Tether
3. Winder
4. Fastener
* Warning： ·Do not put exposed (unconnected) tether into the water or plashing
liquid to the tether.
·Check whether the O-ring on the tether connector pre-dive, make a
replacement when it is missed or damaged.
3
2
4
EN
1
1
06