Quick BTQ2512012 User Manual page 25

POS. DESCRIPTION
1 Motor mounting screw
2 Motor mounting washer
3A Motor 6,5KW 12V
3B Motor 6,5KW 24V
3C Motor 8KW 24V
3D Motor 10KW 24V
4 Key 6x6x25
5 Half-joint
6 Even tension device
7 Motor flange
8 O-Ring
9 Gearbox gasket
10 Gearleg
11 Key 6x6x40
12 Starboard propeller
13 Port propeller
14 Self-braking nut M16
15 Anode tip
16 Anode tip mounting screw
17 Grower Ø10
18 Gearleg mounting screw
19 Clamp reversing contactor unit MMSTBTQ35000
20 Screw M5x06
21 Grower Ø5
22 Washer Ø5
23 Screw M5x12
24A Reversing contactor unit
350A 12V
24B Cassetta teleinvertitori
350A 24V
25 Carter spacer B
26 Fasteners carter
reversing contactor unit
27 Fasteners carter
reversing contactor unit
28 Negative reversing contactor
29 Command wire
BOW THRUSTER BTQ250 - BTQ300 IT GB - REV002A
CODE
MBV1230MXCE0
MBR12X000000
Quick
E M F E L 6 5 1 2 0 0 0
ant to the sea environment: In any case, it is indispensable
E M F E L 6 5 2 4 0 0 0
to periodically remove salt deposits that form on the outer
E M F E L 8 0 2 4 0 0 0
EMFEL1K24000 surfaces to avoid corrosions and consequent system inef-
MBH0606025X0
ficiency.
MMSGM1900000
P V P R 7 0 0 0 0 0 0 0
Dismantle once a year, following the points below:
SLMMEM250000
• Keep the propeller (12 and 13) and the gearleg (10) clean.
P G R 0 4 1 7 5 0 0 0 0
• Paint the propeller and the gearleg with anti-vegetative
P G R D E L 2 5 0 0 0 0
paint before each season.
MREM25000000
MBH0606040X0
P V E L 2 5 R 0 0 0 0 0
P V E L 2 5 L 0 0 0 0 0
MBD16MXET000
MMANBTQ25000
MBV0635MBCE0
• Check the zinc anode (15) frequently.
MBG10X000000
• Replace the zinc anode before every season or when it is
MBV1050MXCE0
more than half consumed.
MBV0506MTCT0 • After any maintenance, make sure that the bolts (18) that
MBG05X000000
lock the flange (7) to the gearleg (10) are well tightened.
MBR051510X00
• After every maintenance, make sure that the propeller (12
MBV0512MXCE0
and 13) is well tightened and that the bolts (1) locking the
electric motor (3) are tight.
E R B T Q 1 2 3 5 0 0 0
• Make sure that all electrical connections are clean and
firmly fixed (28 and 29).
E R B T Q 2 4 3 5 0 0 0
• Make sure that the batteries are in good condition.
MBTCB2600TMM
PCCCBTQB0000
PBD04STPN000
SAECCCBTQNG0
SAECCCBTQCM0
MAINTENANCE
WARNING: make sure that the power supply to the
electric motor is not switched on when maintenance
operations are carried out.
® Bow Thrusters are made in materials that are resist-
:
WARNING do not paint the zinc anode (15), the seal-
ings and the propeller shaft Be careful not to allow
paint to penetrate in the "tracks" of the gearleg (10)
in which the propeller hub moves.
GB
25