Quick BTQ2512012 User Manual page 27

POS. DESCRIPTION
1 Motor mounting screw
2 Motor mounting washer
3A Motor 10KW
3B Motor 12KW
4 Key 6x6x25
5 Half-joint
6 Even tension device
7 Half-joint
8 Motor flange
9 O-Ring
10 Gearbox gasket
11 Key 6x6x20
12 Gearleg
13 Starboard propeller
14 Port propeller
15 Self-braking nut M18
16 Anode tip
17 Anode tip mounting screw
18 Washer Ø14
19 Gearleg mounting screw M14
20 Clamp reversing contactor unit MMSTBTQ35000
21 Screw M5x06
22 Grower Ø5
23 Washer Ø5
24 Screw M5x10
25 Reversing contactor unit
350A 24V
26 Carter spacer B
27 Fasteners carter
reversing contactor unit
28 Fasteners carter
reversing contactor unit
29 Negative reversing contactor
30 Command wire
BOW THRUSTER BTQ250 - BTQ300 IT GB - REV002A
CODE
MBV1230MXCE0
MBR12X000000
Quick
EMFEL1K24000
ant to the sea environment: In any case, it is indispensable
EMFEL2K24000
to periodically remove salt deposits that form on the outer
MBH0606025X0
MMSGM1900000 surfaces to avoid corrosions and consequent system inef-
P V P R 7 0 0 0 0 0 0 0
ficiency
MMSGM2400000
SLMMEM300000
Dismantle once a year, following the points below:
P G R 0 4 1 7 5 0 0 0 0
• Keep the propeller (13 and 14) and the gearleg (12) clean.
P G R D E L 3 0 0 0 0 0
• Paint the propeller and the gearleg with anti-vegetative
MBH0606020X0
paint before each season.
MREM30000000
P V E L 3 0 R 0 0 0 0 0
P V E L 3 0 L 0 0 0 0 0
MBD18MXET000
MMANBTQ30000
MBV0635MBCE0
MBR14X000000
• Check the zinc anode (16) frequently.
MBV1475MXCE0
• Replace the zinc anode before every season or when it is
more than half consumed.
MBV0506MTCT0
• After any maintenance, make sure that the bolts (19) that
MBG05X000000
lock the flange (8) to the gearleg (12) are well tightened.
MBR051510X00
• After every maintenance, make sure that the propeller (13
MBV0510MXCE0
and 14) is well tightened and that the bolts (1) locking the
E R B T Q 2 4 3 5 0 0 0
electric motor (3) are tight.
MBTCB2600TMM
• Make sure that all electrical connections are clean and
firmly fixed ( 29 and 30).
PCCCBTQB0000
• Make sure that the batteries are in good condition.
PBD04STPN000
SAECCCBTQNG0
SAECCCBTQCM0
MAINTENANCE
WARNING: make sure that the power supply to the
electric motor is not switched on when maintenance
operations are carried out.
® Bow Thrusters are made in materials that are resist-
:
WARNING do not paint the zinc anode (16), the seal-
ings and the propeller shafts. Be careful not to allow
paint to penetrate in the "tracks" of the gearleg (12)
in which the propeller hub moves.
GB
27