Advertisement
Quick Links
Pneumatic Arm Single Monitor Desk Mount
Instruction Manual
SKU: STAND-V101H
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
https://vivo-us.com/products/stand-v101h
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
help@vivo-us.com
www.vivo-us.com
Chat live with an agent!
309-278-5303
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Vivo STAND-V101H
Summary of Contents for Vivo STAND-V101H
- Page 1 Pneumatic Arm Single Monitor Desk Mount Instruction Manual SKU: STAND-V101H Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. https://vivo-us.com/products/stand-v101h GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST help@vivo-us.com...
-
Page 2: Package Contents
WARNING! If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. -
Page 3: Tools Needed
TOOLS NEEDED DO NOT EXCEED WEIGHT CAPACITY. 4-26.4lbs Failure to do so may result in serious injury. (1.81-11.97kg) Phillips Wrench Screwdriver ASSEMBLY STEPS STEP 1 STEP 2 Slide Base Cover (F) onto Pole (E). Stick Rubber Pads (J) to the underside of Clamp Brace (C). - Page 4 STEP 3 (Option B) Grommet Base Installation Thread Pole (E) onto Grommet Base (D), tighten pre-installed set screws with 3mm Allen Wrench (T-A), and press Base Cover (F) into place. Stick Rubber Pads (J) to the underside of Grommet Base (D). Remove screw from end of Hand Bolt (B1) on Clamp (B) and separate parts.
- Page 5 STEP 5 OPTION A: Flat Back Monitor For flat back monitors, install VESA Plate (G) to monitor using Screws (M-A) or (M-C) and M5 Washers (M-E). OPTION B: Curved Back Monitor For curved back monitors, install VESA Plate (G) to monitor using Screws (M-B) or (M-D), M5 Washers (M-E), and Spacers (M-F).
- Page 6 STEP 6 Slide VESA Plate (G) over bracket on Monitor Arm (A). Secure using Thumbscrew (S-B). STEP 7 Remove bottom cover from Monitor Arm (A) by sliding cover forward and off. STEP 8 Run cables through bottom of Monitor Arm (A). Reattach cover.
- Page 7 STEP 9 Adjust tension in Monitor Arm (A) and angle of monitor using 6mm Allen Wrench (T-C). Clockwise reduces tension, counterclockwise increases tension. The tension should be just enough to hold your monitor in place without lifting itself up. STEP 10 Adjust monitor to desired position and store Allen Wrenches (T-A, T-B, T-C) in Cable Clip (I) for future adjustments.
- Page 8 AVG. RESPONSE TIME (within office hrs) - 23% within < 15m - 38% within < 30m - 61% within < 1hr - 83% within < 2hr - 92% within < 3hr FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com...
Need help?
Do you have a question about the STAND-V101H and is the answer not in the manual?
Questions and answers