Gree GWH09ACC-K6DNA1F/I Service Manual page 40

(2) Adjust "▲" a nd "▼" button, could change the corresponding
setting temperature, after adjusted, press "Turbo" button for
confirmation;
(3) At this time, 1hour will be automatically increased at the timer
position on the remote control, (that are "2hours" or "3hours" or "8
hours" ), the place of setting temperature "88" will display the
corresponding temperature of last setting sleep curve and blink;
(4) Repeat the above step (2)~(3) operation, until 8 h
ours tempe rature setting fi nished, sleep,curve setting finished,
at this time, the remote controller will resume the original timer
display; temperature display will resume to original setting
temperature.
●Sleep 3-the sleep curve setting under Sleep mode by DIY could
be inquired:
The user could accord to sleep curve setting method to inquire the
presetting sleep curve, enter into user individuation sleep setting
status, but do not change the temperature, press "Turbo" button
directly for confirmation. Note: In the above presetting or enquiry
procedure, if continuously within 10s, there is no button pressed,
the sleep curve setting within 10s, there is no button pressed , the
sleep curve setting status will be automatically quit and resume
to display the original displaying. In the presetting or enquiry
procedure, press " " button, " Mode " button, " Sleep " button, the
sleep curve setting or enquiry status will quit similarly.
button
Press this button to start I FEEL function and "
displayed on the remote controller. After this function is set, the
remote controller will send the detected ambient temperature
to the controller and the unit will automatically adjust the indoor
temperature according to the detected temperature. Press this
button again to close I FEEL function and " " will disappear.
Please put the remote controller near user when this function
is set. Do not put the remote controller near the object of high
temperature or low temperature in order to avoid detecting
inaccurate ambient temperature. When I FEEL function is turned
on, the remote controller should be put within the area where
indoor unit can receive the signal sent by the remote controller.
/ button
● TIMER ON button
"TIMER ON" button can set the time for timer on. After pressing
this button, " " icon disap-pears and the word "ON" on remote
controller blinks. Press "▲" or "▼" button to adjust TIMER ON
setting. After each pressing of "▲" or "▼"button, TIMER ON
setting will increase or decrease 1min. Holding "▲" or "▼" button,
2s later, the time will change quickly until reaching your required
time.
Press "TIMER ON" to confirm it. The word "ON" will stop blinking.
" " icon resumes displaying. Cancel TIMER ON: Under the
condition that TIMER ON is started up, press "TIMER ON" button
to cancel it.
● TIMER OFF button
"TIMER OFF" button can set the time for timer off. After pressing
this button, " " icon disap-pears and the word "OFF" on remote
controller blinks. Press "▲" or "▼" button to adjust TIMER OFF
setting. After each pressing of "▲" or "▼"button, TIMER OFF
setting will increase or decrease 1min. Holding "▲" or "▼" button,
2s later, the time will change quickly until reaching your required
time.
Press "TIMER OFF" and the word "OFF" will stop blinking. "
icon resumes displaying. Under the condition that TIMER OFF is
started up, press "TIMER OFF" button to cancel it.
Technical Information
*Note:
● Under on and off status, you can set TIMER OFF or TIMER ON
simultaneously.
● Before setting TIMER ON or TIMER OFF, please adjust the
clock time.
● When turning on TIMER ON or TIMER OFF function, set this
function valid all the time and the air condition-er will be turned on
or turned off at set temperature every day. " " button has no affect
to setting. If this function is not required, use the remote controller
to cancel it.
button
Press this button to set clock time. "
will blink. Press "▲" or "▼" button within 5s to set clock time.
Each pressing of "▲" or "▼" button, clock time will increase
or decrease 1 min. If hold "▲" or "▼" button, 2s later, time will
change quickly. Release this button when reaching your required
time. Press "CLOCK" button to confirm the time. "
blinking.
*Note:
● Clock time adopts 24-hour mode.
● The interval between two operations can't exceed 5s. Otherwise,
remote controller will quit setting status. Operation for TIMER ON/
TIMER OFF is the same.
button
" will be
Press this button, the quiet status is under the auto quiet mode
(display " " and "Auto" signal) and quietmode (display "
signal) and quiet off (there is nosignal of "
powered on, the quietoff is defaulted.
*Note:
● The quiet function is only available for some models.
● The Quiet function can be set up in all modes; Under the Quiet
mode,the fan speed is not available.
● When quiet function is selected
Under cooling mode: indoor fan operates at notch 4 speed. 10
minutes later or when indoor ambient temperature ≤ 28
fan will operate at notch 2 speed or quiet mode according to
the comparison between indoor ambient temperature and set
temperature.
Under heating mode: indoor fan operates at notch 3 speed or
quiet mode according to the comparison between indoor ambient
temperature and set temperature.
Under dry, fan mode: indoor fan operates at quiet mode. Under
auto mode: the indoor fan operates at the auto quiet mode
according to actual cooling, heating or fan mode.
button
Press "WiFi" button to turn on WiFi function, "WiFi" icon will be
displayed on the remote controller; Hold "WiFi" button for 5s to
turn off WiFi function and "WiFi" icon will disappear.
Under off status, press "MODE" and "WiFi" buttons simultaneously
for 1s, WiFi module will restore factory settings.
*Note:
● This function is only available for some models.
button
Press this button to turn off display light on indoor unit. "
"
on remote controller disappears. Press this button again to turn on
display light. "
" icon on remote controller
" icon is displayed.
" icon stops
"
" displayed), after
o
C, indoor
" icon
37