Video-inserter compatible with audi vehicles with mmi3g basic/high, mmi3g+ basic/high infotainments vw vehicles with rns850 infotainment and 4pin hsd lvds connector (17 pages)
Video-inserter compatible with chrysler, dodge, jeep vehicles with uconnect 4c nav uav and 8.4inch monitor uconnect nav uax und 12inch monitor with separate head-unit (22 pages)
Video-inserter compatible with vw vehicles with mib3 entry - composition with 8.25inch monitor seat vehicles with mib3 entry - with 8.25inch monitor skoda vehicles with mib3 entry with 8.25inch monitor (24 pages)
Video-inserter vw vehicles with mib2 gp composition color infotainment and 6.5 zoll monitor seat vehicles with mib2 gp media system touch color infotainment and 6.5 zoll monitor skoda vehicles with mib2 gp-radio swing infotainment and 6.5inch monitor (27 pages)
Video inserter compatible with audi vehicles with mmi navigation plus - mib ii infotainment with monitor in instrument lamborghini vehicles with mib infotainment with monitor in instrument (18 pages)
Video-inserter for rear-view camera and two additional video sources, compatible with mazda vehicles with mzd connect infotainment and 7inch monitor (18 pages)
Summary of Contents for NavLinkz RL1-RLK
Page 1
Video-inserter RL1-RLK Compatible with Dacia, Fiat, Smart Renault vehicles with RLink or MediaNav system Opel vehicles with Navi 50 or Navi 80 Video-inserter with 2 video inputs and rear-view camera input Product features • Video-inserter for factory-infotainment systems • 2 video-inputs for after-market devices (e.g. DVD-Player, DVB-T tuner) •...
Legal Information By law, watching moving pictures while driving is prohibited, the driver must not be distracted. We do not accept any liability for material damage or personal injury resulting, directly or indirectly, from installation or operation of this product. This product should only be used while standing or to display fixed menus or rear-view-camera video when the vehicle is moving, for example the MP3 menu for DVD upgrades.
1.2. Checking the compatibility of vehicle and accessories Requirements Brand Compatible vehicles Compatible systems Dokker since 2013-, Duster since 2014, Lodgy since 2012, Dacia MediaNav Logan since 2013, Sandero since 2012 Fiat Talento model year since 2016 MediaNav Navi 50 (MediaNav), Opel Movano since about 2016, Vivaro since about 2016 til 2019 Navi 80 IntelliLink (Rlink)
1.3.1.1. Dip-switch settings Some settings must be selected by the dip-switches on the video-interface. Dip position down is ON and position up is OFF. Function ON (down) OFF (up) No function set to OFF CVBS AV1-input enabled disabled CVBS AV2-input enabled disabled No function...
2. Installation Switch off ignition and disconnect the vehicle’s battery! The interface needs a permanent 12V source. If according to factory rules disconnecting the battery is to be avoided, it is usually sufficient to put the vehicle to “Sleep-Mode”. In case it does not succeed, disconnect the battery with a resistor lead.
2.3. Connection – 6pin interface cable Connect the white female 6pin connector of the 6pin interface cable to the male 6pin connector of the video interface. Connect the green wire of the 6pin interface cable to +12V of the reverse gear signal. (e.g.
2.4. Installation - Ribbon cables into the Monitor panel Remove the factory monitor and open it`s housing. The external daughter PCB is built to be installed into the optical lead between the monitor panel and mainboard of the vehicles monitor. The daughter PCB is equipped with to different ribbon cable options to support two different monitor systems.
2.4.1. Media Nav with 50pin Ribbon cable Disconnect the optical leads housed between the monitor`s mainboard and the monitor- panel. Connect the daughter PCB’s ribbon cable CAR-IN to the ribbon cable base of the monitor`s mainboard. For this procedure you may either use the original ribbon cable or the ribbon cable of the daughter PCB.
Page 11
2.4.2. R-Link with 60pin Flex cable Remove the Ribbon cable between the monitor’s monitor panel and the monitor PCB. Connect the daughter PCB’s ribbon cable CAR-IN to the ribbon cable base of the main PCB. For this procedure you may either use the original ribbon cable or the ribbon cable of daughter PCB.
2.5. Connection - video sources It is possible to connect two after-market video sources and one after-market rear-view camera to the video-interface. Before final installation of the peripheral devices, we recommend a test-run to detect a incompatibility of vehicle and interface. Due to changes in the production of the vehicle manufacturer there’s always a possibility of incompatibility.
2.5.1. After-market rear-view camera Note: Do not forget to set dip5 of video-interface to ON before testing. To switch to the rear-view camera when reverse gear is engaged, an external switching signal from the reverse gear light is required. As the reverse gear light signal contains electronic interference, a traditional open relay (e.g AC-RW-1230 with wiring AC-RS5) or filter (e.g.
2.5.2. Audio Insertion This interface can only insert video signals into the factory infotainment. If an AV-source is connected, audio insertion must be done by factory audio AUX input or FM-modulator. If no factory AUX input is available, the optional audio-AUX cable (item no. AUX-006) can be used for a connection to the factory radio plug (coding required!).The inserted video-signal can be activated simultaneously to each audio-mode of the factory infotainment.
2.7. Picture settings The picture settings are adjusted by the 3 buttons on the video-interface. Press the MENU button to open the OSD settings menu or to switch to the next menu item. Press UP and DOWN change the selected value. The buttons are embedded in the housing to avoid accidental changes during or after installation.
3. Interface operation Press theinterface’s external keypad to switch the video source. Each repetition will switch to the next enabled input. If all inputs are enabled the order is: → → → → Factory video video IN1 video IN2 factory video Disabled inputs will be skipped.
Page 17
FAQ – Trouble shooting Interface functions For any troubles which may occur, check the following table for a solution before requesting support from your vendor. Symptom Reason Possible solution Not all connectors have been reconnected to factory head- Connect missing connectors. unit or monitor after installation.
6pin to 8pin cable and isolate both ends. Technical Support Please note that direct technical support is only available for products purchased directly from NavLinkz GmbH. For products bought from other sources, contact your vendor for technical support. NavLinkz GmbH...